ANSI ASME A112.3.4-2013 Plumbing fixtures with pumped waste and macerating toilet systems《带泵送废物和浸渍盥洗系统的浴间设备》.pdf

1、ASME A112.3.4-2013/CSA B45.9-13Plumbing fixtures with pumped waste and macerating toilet systemsLegal Notice for Harmonized StandardJointly Developed by ASME and CSA GroupIntellectual property rights and ownershipAs between American Society of Mechanical Engineers (ASME) and Canadian Standards Assoc

2、iation (Operating as “CSA Group) (collectively ASME and CSA Group) and the users of this document (whether it be in printed or electronic form), ASME and CSA Group are the joint owners of all works contained herein that are protected by copyright, all trade-marks (except as otherwise noted to the co

3、ntrary), and all inventions and trade secrets that may be contained in this document, whether or not such inventions and trade secrets are protected by patents and applications for patents. The unauthorized use, modification, copying, or disclosure of this document may violate laws that protect the

4、intellectual property of ASME and CSA Group and may give rise to a right in ASME and CSA Group to seek legal redress for such use, modification, copying, or disclosure. ASME and CSA Group reserve all intellectual property rights in this document.Disclaimer and exclusion of liabilityThis document is

5、provided without any representations, warranties, or conditions of any kind, express or implied, including, without limitation, implied warranties or conditions concerning this documents fitness for a particular purpose or use, its merchantability, or its non-infringement of any third partys intelle

6、ctual property rights. ASME and CSA Group do not warrant the accuracy, completeness, or currency of any of the information published in this document. ASME and CSA Group make no representations or warranties regarding this documents compliance with any applicable statute, rule, or regulation.IN NO E

7、VENT SHALL ASME AND CSA GROUP, THEIR RESPECTIVE VOLUNTEERS, MEMBERS, SUBSIDIARIES, OR AFFILIATED COMPANIES, OR THEIR EMPLOYEES, DIRECTORS, OR OFFICERS, BE LIABLE FOR ANY DIRECT, INDIRECT, OR INCIDENTAL DAMAGES, INJURY, LOSS, COSTS, OR EXPENSES, HOWSOEVER CAUSED, INCLUDING BUT NOT LIMITED TO SPECIAL

8、OR CONSEQUENTIAL DAMAGES, LOST REVENUE, BUSINESS INTERRUPTION, LOST OR DAMAGED DATA, OR ANY OTHER COMMERCIAL OR ECONOMIC LOSS, WHETHER BASED IN CONTRACT, TORT (INCLUDING NEGLIGENCE), OR ANY OTHER THEORY OF LIABILITY, ARISING OUT OF OR RESULTING FROM ACCESS TO OR POSSESSION OR USE OF THIS DOCUMENT, E

9、VEN IF ASME OR CSA GROUP HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES, INJURY, LOSS, COSTS, OR EXPENSES.In publishing and making this document available, ASME and CSA Group are not undertaking to render professional or other services for or on behalf of any person or entity or to perform any

10、 duty owed by any person or entity to another person or entity. The information in this document is directed to those who have the appropriate degree of experience to use and apply its contents, and ASME and CSA Group accept no responsibility whatsoever arising in any way from any and all use of or

11、reliance on the information contained in this document. ASME and CSA Group have no power, nor do they undertake, to enforce compliance with the contents of the standards or other documents they jointly publish. Authorized use of this documentThis document is being provided by ASME and CSA Group for

12、informational and non-commercial use only. The user of this document is authorized to do only the following:If this document is in electronic form:. load this document onto a computer for the sole purpose of reviewing it;. search and browse this document; and. print this document if it is in PDF for

13、mat.Limited copies of this document in print or paper form may be distributed only to persons who are authorized by ASME and CSA Group to have such copies, and only if this Legal Notice appears on each such copy.In addition, users may not and may not permit others to. alter this document in any way

14、or remove this Legal Notice from the attached standard;. sell this document without authorization from ASME and CSA Group ; or. make an electronic copy of this document.If you do not agree with any of the terms and conditions contained in this Legal Notice, you may not load or use this document or m

15、ake any copies of the contents hereof, and if you do make such copies, you are required to destroy them immediately. Use of this document constitutes your acceptance of the terms and conditions of this Legal Notice.Standards Update ServiceASME A112.3.4-2013/CSA B45.9-13December 2013Title: Plumbing f

16、ixtures with pumped waste and macerating toilet systemsPagination: 19 pages (xii preliminary and 7 text), each dated December 2013To register for e-mail notification about any updates to this publication go to shop.csa.caclick on CSA Update ServiceThe List ID that you will need to register for updat

17、es to this publication is 2422100.If you require assistance, please e-mail techsupportcsagroup.org or call 416-747-2233.Visit CSA Groups policy on privacy at csagroup.org/legal to find out how we protect your personal information.TMA trade-mark of the Canadian Standards Association, operating as “CS

18、A Group”Published in December 2013 by CSA GroupA not-for-profit private sector organization5060 Spectrum Way, Suite 100, Mississauga, Ontario, Canada L4W 5N61-800-463-6727 416-747-4044Visit our Online Store at shop.csa.caASME A112.3.4-2013/CSA B45.9-13Plumbing fixtures with pumped waste and macerati

19、ng toilet systemsPublished in December 2013 by CSA GroupA not-for-profit private sector organization5060 Spectrum Way, Suite 100Mississauga, Ontario, CanadaL4W 5N61-800-463-6727 g120 416-747-4044Visit the CSA Online Store at shop.csa.caISBN 978-1-77139-031-6 2013 CSA GroupAll rights reserved. No par

20、t of this publication may be reproduced in any form whatsoever without the prior permission of the publisher.Commitment for AmendmentsThis Standard is issued jointly by the American Society of Mechanical Engineers (ASME) and the Canadian Standards Association (Operating as “CSA Group”). Amendments t

21、o this Standard will be made only after processing according to the Standards writing procedures of both ASME and CSA Group.The American Society of Mechanical Engineers (ASME) Two Park AvenueNew York, NY 10016-5990USAwww.asme.orgISBN 978-0-7918-6917-8 Copyright 2013The 2013 edition of this Standard

22、is being issued with an automatic addenda subscription service. The use of addenda allows revisions made in response to public review comments or committee actions to be published as necessary.December 2013 iiiContents The American Society of Mechanical Engineers 2013 CSA GroupPlumbing fixtures with

23、 pumped waste and macerating toilet systemsASME A112 Standards Committee on Plumbing Materials and Equipment vASME A112.19.2 Project Team on Vitreous China Plumbing Fixtures (A112) viiCSA Technical Committee on Plumbing Fixtures (B45) viiiCSA/ASME Harmonization Task Group on Plumbing Fixtures (B45-J

24、HTG) xPreface xi1Scope 12 Reference publications 23 Definitions and abbreviations 33.1 Definitions 33.2 Abbreviations 34 Material requirements and general requirements 34.1 Materials 34.1.1 Pumps 34.1.2 Gaskets 34.1.3 Electrical requirements 44.1.4 Water closets 44.1.5 Lavatories and sinks 44.1.6 Ba

25、thtubs 44.1.7 Showers 44.1.8 Macerating system housing 44.1.9 Clamps 44.2 General requirements 44.2.1 Fastening 44.2.2 Return of discharged wastes 44.2.3 Accessibility 44.2.4 Function 54.2.5 Hydrostatic pressure integrity 54.2.6 Minimum size 54.2.7 Venting 54.3 Pumped waste components 54.3.1 Pump 54

26、.3.2 Discharge pipe 54.3.3 Backflow prevention 54.3.4 Venting not required 55 Performance tests 55.1 Cycle testing 55.1.1 Test method 55.1.2 Acceptance criteria 65.2 Paper test of the assembled unit 65.2.1 Set-up 65.2.2 Test procedure 65.2.3 Performance requirement 6 The American Society of Mechanic

27、al EngineersASME A112.3.4-2013/CSA B45.9-13 2013 CSA Groupiv December 20135.3 Hydrostatic pressure test of the check valve 65.3.1 Test method 65.3.2 Performance requirement 65.4 Hydrostatic pressure test of the holding tank assembly 75.4.1 Test method 75.4.2 Performance requirement 75.5 Discharge te

28、st 75.5.1 Test method 75.5.2 Performance 76 Marking and instruction requirements 76.1 Marking 76.2 Instructions 76.2.1 Installation 76.2.2 Owner/operator instructions 7 The American Society of Mechanical Engineers 2013 CSA GroupPlumbing fixtures with pumped waste and macerating toilet systemsDecembe

29、r 2013 vASME A112 Standards Committee on Plumbing Materials and EquipmentD.W. Viola IAPMO,Mokena, Illinois, USAChairS. Rawalpindiwala Kohler Co.,Kohler, Wisconsin, USAVice-ChairR.K. Adler City of San Jose,San Jose, California, USAS.F. Aridi NSF International,Ann Arbor, Michigan, USAJ.A. Ballanco JB

30、Engineering however, they should not contain proprietary names or information.ASME procedures provide for reconsideration of any interpretation when or if additional information that might affect an interpretation is available. Further, persons aggrieved by an interpretation may appeal to the cogniz

31、ant ASME Committee.Interpretations are published on the ASME Web site under the Committee Pages at http:/www.asme.org/codes/ as they are issued.CSA Notes: (1) Use of the singular does not exclude the plural (and vice versa) when the sense allows.(2) Although the intended primary application of this

32、Standard is stated in its Scope, it is important to note that it remains the responsibility of the users of the Standard to judge its suitability for their particular purpose. The American Society of Mechanical EngineersASME A112.3.4-2013/CSA B45.9-13 2013 CSA Groupxii December 2013(3) This publicat

33、ion was developed by consensus, which is defined by CSA Policy governing standardization Code of good practice for standardization as “substantial agreement. Consensus implies much more than a simple majority, but not necessarily unanimity”. It is consistent with this definition that a member may be

34、 included in the Technical Committee list and yet not be in full agreement with all clauses of this publication.(4) CSA Standards are subject to periodic review, and suggestions for their improvement will be referred to the appropriate committee.(5) All enquiries regarding this Standard, including r

35、equests for interpretation, should be addressed to Canadian Standards Association, 5060 Spectrum Way, Suite 100, Mississauga, Ontario, Canada L4W 5N6. Requests for interpretation should(a) define the problem, making reference to the specific clause, and, where appropriate, include an illustrative sk

36、etch;(b) provide an explanation of circumstances surrounding the actual field condition; and(c) be phrased where possible to permit a specific “yes” or “no” answer.Committee interpretations are processed in accordance with the CSA Directives and guidelines governingstandardization and are published

37、in CSAs periodical Info Update, which is available on the CSA Web site atwww.csa.ca.Attention is drawn to the possibility that some of the elements of this Standard may be the subject of patent rights. CSA is not to be held responsible for identifying any or all such patent rights. Users of this Sta

38、ndard are expressly advised that determination of the validity of any such patent rights is entirely their own responsibility. The American Society of Mechanical Engineers 2013 CSA Group Plumbing fixtures with pumped waste and macerating toilet systemsDecember 2013 1ASME A112.3.4-2013/CSA B45.9-13Pl

39、umbing fixtures with pumped waste and macerating toilet systems1 Scope1.1This Standard establishes physical, performance, and testing requirements applicable to plumbing fixtures with pumped waste, macerating toilet systems, and related components. Such systems are intended to collect waste from a s

40、ingle fixture such as a water closet, lavatory, shower, or bathtub and pump these wastes to some point in the sanitary drainage system.1.2The purpose of this Standard is to establish a generally acceptable performance standard for pumped waste systems, macerating systems and related components for d

41、irectly affixed water closets and other fixtures designed for above the-floor or in-floor installations.1.3A water closet connects to a macerating toilet system. Macerating toilet systems collect the waste from a single water closet, plus a lavatory, shower, bathtub, or a combination of these in the

42、 same room. Macerating systems grind and pump these macerated wastes to some point in the sanitary drainage system.1.4Pumped waste systems consist of three major components:(a) an automatic activation of the pumped waste system;(b) a drainage connection to the pump; and(c) a pump that pumps the wast

43、e to the gravity drainage system.1.5The macerating system comprises three major components:(a) a container that houses the operating mechanisms;(b) a pressure chamber that automatically or manually activates and deactivates the induction motor; and(c) an induction motor that drives the shredder blad

44、es and pump assembly, which is permitted to be combined into a single unit.1.6The use of alternate materials or methods is permitted, provided it can be demonstrated that such alternatives comply with the performance requirements of this Standard.1.7In this Standard, “shall” is used to express a req

45、uirement, i.e., a provision that the user is obliged to satisfy in order to comply with the standard; “should” is used to express a recommendation or that which is advised but not required; “may” is used to express an option or that which is permissible within the limits of the standard; and “can” i

46、s used to express possibility or capability. The American Society of Mechanical EngineersASME A112.3.4-2013/CSA B45.9-13 2013 CSA Group2 December 2013Notes accompanying clauses do not include requirements or alternative requirements; the purpose of a note accompanying a clause is to separate from th

47、e text explanatory or informative material. Notes to tables and figures are considered part of the table or figure and may be written as requirements. Annexes are designated normative (mandatory) or informative (non-mandatory) to define their application.1.8 Units of measurementSI units are the unit

48、s of record in Canada. In this Standard, the inch/pound units are shown in parentheses.The values stated in each measurement system are equivalent in application; however, each system is to be used independently. Combining values from the two measurement systems can result in non-conformance with th

49、is Standard.All references to gallons are to U.S. gallons.2 Reference publicationsThis Standard refers to the following publications, and where such reference is made, it shall be to the edition listed below, including all amendments published thereto.ASTM International (American Society for Testing and Materials)C1173-10Flexible Transition Couplings for Underground Piping SystemsCSA GroupCAN/CSA-C22.2 No. 108-01 (R2010)Liquid pumpsCAN/CSA B602-10Mechanical couplings for drain, waste, and vent pipe and sewer pipeCSA Group/IAPMO (International Associatio