ANSI ASTM D4730-2013 Standard Specification for Flooding Compounds for Telecommunications Wire and Cable《电信电线和电缆浸渍化合物规格》.pdf

1、Designation: D4730 13Standard Specification forFlooding Compounds for Telecommunications Wire andCable1This standard is issued under the fixed designation D4730; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the year of last revi

2、sion. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope*1.1 This specification covers a variety of compounds usedfor flooding the shields and armors of telecommunicationswires and cables

3、 (both electrical and fiber optic) for thepurpose of preventing water and other undesirable fluids fromentering or migrating along or through the cable sheath. (Forrelated standards see Specifications D4731 and D4732.)2. Referenced Documents2.1 ASTM Standards:2D6 Test Method for Loss on Heating of O

4、il and AsphalticCompoundsD92 Test Method for Flash and Fire Points by ClevelandOpen Cup TesterD482 Test Method for Ash from Petroleum ProductsD1321 Test Method for Needle Penetration of PetroleumWaxesD3236 Test Method for Apparent Viscosity of Hot MeltAdhesives and Coating MaterialsD4565 Test Method

5、s for Physical and Environmental Per-formance Properties of Insulations and Jackets for Tele-communications Wire and CableD4568 Test Methods for Evaluating Compatibility BetweenCable Filling and Flooding Compounds And PolyolefinWire and Cable MaterialsD4731 Specification for Hot-Application Filling

6、Com-pounds for Telecommunications Wire and CableD4732 Specification for Cool-Application Filling Com-pounds for Telecommunications Wire and CableE28 Test Methods for Softening Point of Resins Derivedfrom Pine Chemicals and Hydrocarbons, by Ring-and-Ball Apparatus3. Terminology3.1 Definitions of Term

7、s Specific to This Standard:3.1.1 flooding compoundsany of several materials used tofill the air spaces between the sheath elements of single andmulti-conductor insulated wires and cables or optical cables forthe purpose of excluding water and other undesirable fluids;especially with regard to telec

8、ommunications wire and cable,including optical cable, intended for outside aerial or under-ground installations.3.1.2 producerthe primary manufacturer of the material.3.1.3 suppliersjobbers and distributors as distinct fromproducers.4. Ordering Information4.1 Orders for material under this specifica

9、tion shall includethe following information:4.1.1 Quantity (mass or volume) of each item,4.1.2 Generic name of the material, such as cable floodingcompound,4.1.3 How furnished (drums or barrels, blocks, etc.),4.1.4 Certification, if required (see Section 11).4.1.5 This specification designation, and

10、4.1.6 Any special requirements, as listed in 8.2 and 9.2, thatapply.5. Materials and Manufacture5.1 The material and manufacturing methods used shall besuch that the resulting products conform to the properties andcharacteristics prescribed in this specification.6. Compatibility with Other Materials

11、6.1 It is the responsibility of the purchaser to ensure that theflooding compound ordered is suitable for the intended appli-cation and is compatible with any other components that maycome into contact with the flooding compound.6.2 The purchaser shall specify the materials that the com-pound must b

12、e compatible with when tested in accordance withTest Method D4568.7. Chemical Composition7.1 The chemical composition of these materials is notspecified. The material shall be of a chemical composition1This specification is under the jurisdiction of ASTM Committee D09 onElectrical and Electronic Ins

13、ulating Materials and is under the direct responsibilityof Subcommittee D09.07 on Electrical Insulating Materials.Current edition approved May 1, 2013. Published June 2013. Originallyapproved in 1987. Last previous edition approved in 2008 as D4730 02 (2008).DOI: 10.1520/D4730-13.2For referenced AST

14、M standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.*A Summary of Changes section appears at the end of this standardCopyright ASTM

15、International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States1suitable for the intended purpose and which meets the require-ments of this specification as hereinafter stated.7.2 Once established, the producer shall not change thecomposition of the compound in suc

16、cessive lots of materialwithout prior approval of the purchaser.8. Physical Properties8.1 Flooding compound furnished under this specificationshall inhibit the corrosion of any metallic wire and cableelements with which it comes in contact, while serving as aradial and longitudinal barrier to moistu

17、re transmission. Con-tact of the flooding compound with any cable component shallnot cause degradation of performance of the cable component.The flooding compound shall display adhesive properties toprovide adhesion between metallic sheath elements and theouter jacket materials of wire and cable.8.2

18、 Other Properties:8.2.1 Other physical properties requirements such as Vis-cosity (for example, Test Method D3236), Flash Point (forexample, Test Method D92), Needle Penetration (for example,Test Method D1321), Ring-and-Ball Softening Point (forexample, Test Method E28), and Heat Stability/Viscosity

19、Change (for example, Test Method D3236), are specified, ifneeded, and shall be as agreed-upon between the producer andthe purchaser.8.3 The purchaser (individual cable manufacturer or other)shall specify any other expected requirements needed to ensurecompliance with such end-product requirements as

20、 cold-bend,low-temperature flexibility, and the like (for example, TestMethods D4565).9. General Requirements9.1 All flooding compounds manufactured in conformanceto this specification shall meet the following requirements:9.1.1 HomogeneityThe compound shall be homogeneousand uniformly mixed.9.1.2 F

21、oreign MaterialThe compounds shall be free ofdirt, metallic particles, and other foreign matter.9.2 Other Properties:9.2.1 Other raw material requirements such as Volatility (forexample, Test Method D6), Metals Content (for example, TestMethod D482), adhesive property measurements, and corro-sion in

22、hibiting characteristics are specified, if needed, and shallbe as agreed-upon between the producer and the purchaser.9.3 The purchaser (individual cable manufacturer or other)shall specify any other expected requirements needed to ensurecompliance with such end-product requirements as cabledrip-out

23、temperature and jacket slip.10. Quality Assurance10.1 Responsibility for Inspection and TestsUnless other-wise specified in the contract or purchase order, the producer isresponsible for the performance of all inspection and testrequirements specified herein. The producer shall use his ownor any oth

24、er suitable facilities for the performance of theinspection and test requirements specified herein, unless oth-erwise stated by the purchaser in the order or at the time of thecontract signing. The purchaser shall have the right to performany of the inspections and tests set forth in this specificat

25、ionwhere such inspections are deemed necessary to assure that thematerial conforms to prescribed requirements.10.2 Each producer shall establish written nominal valuesand tolerances for the material properties routinely checked.For properties not routinely checked, typical values shall bespecified.

26、Once these values have been accepted by thepurchaser, the producer shall not ship material which deviatesfrom these limits without prior notification to and approval bythe purchaser.10.3 An inspection lot shall consist of an identifiable quan-tity of the same material subjected to inspection at one

27、time.11. Certification11.1 The producer or supplier shall, on request, furnish tothe purchaser a certificate stating that each lot has beensampled, tested, and inspected in accordance with thisspecification, and has met the requirements.12. Packaging and Package Marking12.1 PackagingThe flooding com

28、pound shall be packagedin a manner that protects the material from contaminationduring shipment.12.2 Package MarkingShipping containers shall bemarked with the name of the manufacturer, trade name, type ofmaterial, lot number, mass or volume, and date of manufacture.13. Keywords13.1 adhesive; compat

29、ibility; flooding compound; moisturebarrier; telecommunications wire and cableD4730 132SUMMARY OF CHANGESCommittee D09 has identified the location of selected changes to this standard since the last issue(D4730 02R08) that may impact the use of this standard. (Approved May 1, 2013.)(1) Deleted “will

30、” in 5.1.(2) Changed “that may come” to “that come” in 6.1.(3) Changed “may” to “shall” and “any” to “a” in 7.1.(4) Changed “may be” to “are” in 8.2.1 and 9.2.1.(5) Changed “The producer may” to “The producer shall” in10.1.ASTM International takes no position respecting the validity of any patent ri

31、ghts asserted in connection with any item mentionedin this standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the riskof infringement of such rights, are entirely their own responsibility.This standard is subject to revision at an

32、y time by the responsible technical committee and must be reviewed every five years andif not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional standardsand should be addressed to ASTM International Headquarters. Your comments w

33、ill receive careful consideration at a meeting of theresponsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you shouldmake your views known to the ASTM Committee on Standards, at the address shown below.This standard is copyrighted by A

34、STM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org). Permission rights to photocopy the standard may also be secured from the Copyright Clearance Center, 222Rosewood Drive, Danvers, MA 01923, Tel: (978) 646-2600; http:/ 133