ANSI ASTM F1199-1988 Standard Specification for Cast (All Temperatures and Pressures) and Welded Pipe Line Strainers (150 psig and 150 Degrees F Maximum)《铸造(所有温度和压力)和焊接管线滤网(150 psi.pdf

1、Designation: F1199 88 (Reapproved 2015) An American National StandardStandard Specification forCast (All Temperatures and Pressures) and Welded PipeLine Strainers (150 psig and 150F Maximum)1This standard is issued under the fixed designation F1199; the number immediately following the designation i

2、ndicates the year oforiginal adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope1.1 This specification covers all cast stra

3、iners and weldedstrainers in services up to 150 psig and 150F (1 MPa and65C). For welded strainers used in services above 150 psigand 150F, see Specification F1200.1.2 This standard provides the minimum requirements forthe design, fabrication, rating, marking, and testing of cast andwelded pipe line

4、 strainers for services above 0F (18C).1.3 Strainers manufactured to this specification are accept-able for use in the marine environment.1.4 The values stated in inch-pound units are to be regardedas standard. The values given in parentheses are mathematicalconversions to SI units that are provided

5、 for information onlyand are not considered standard.1.5 The following safety hazards caveat pertains only to thetest methods portion, Section 8, of this specification. Thisstandard does not purport to address all of the safety concerns,if any, associated with its use. It is the responsibility of th

6、e userof this standard to establish appropriate safety and healthpractices and determine the applicability of regulatory limita-tions prior to use.2. Referenced Documents2.1 ASTM Standards:2F1200 Specification for Fabricated (Welded) Pipe LineStrainers (Above 150 psig and 150F)2.2 ANSI Standards:3B2

7、.1 Pipe ThreadsB16.1 Cast Iron Pipe Flanges and Flanged FittingsB16.3 Malleable Iron Threaded FittingsB16.4 Cast Iron Threaded FittingsB16.5 Steel Pipe Flanges and Flanged FittingsB16.11 Forged Steel Fittings, Socket-Welding and ThreadedB16.15 Cast Bronze Threaded FittingsB16.24 Bronze Pipe Flanges

8、and Flanged FittingsB16.25 Buttwelding EndsB31.1 Power Piping2.3 MSS Standards:4SP-51 150 lb Corrosion Resistant Cast Flanges and FlangedFittingsSP-63 High Strength Wrought Welding Fittings2.4 ASME Standards:5ASME Boiler and Pressure Vessel Code Section VIII, Divi-sion 1, Pressure Vessels3. Terminol

9、ogy3.1 Definitions:3.1.1 basket or elementthe replaceable part in a strainerthat performs the barrier separation of solid particles fromflowing fluid. It is normally removable for cleaning andservicing and can be furnished in a wide variety of materials,particle size removal capability, straining ar

10、ea, and types ofconstruction. Interchangeable baskets or elements are normallyavailable for a given make, model, and size strainer.3.1.2 maximum allowable working pressure (MAWP)thehighest internal pressure that the strainer can be subjected to inservice. The maximum nonshock working pressure for wh

11、ich astrainer is rated by the manufacturer.3.1.3 maximum design temperaturethe maximum tem-perature for which a strainer is rated by the manufacturer.3.1.4 strainera device which, when installed in a pipeline, provides a mechanical means of removing solids from aflowing liquid or gas by using a barr

12、ier element.3.1.5 straining open areathe net effective open area of theclean element through which the fluid can pass.1This specification is under the jurisdiction of ASTM Committee F25 on Shipsand Marine Technology and is the direct responsibility of Subcommittee F25.11 onMachinery and Piping Syste

13、ms.Current edition approved May 1, 2015. Published June 2015. Originallyapproved in 1988. Last previous edition approved in 2010 as F1199 88 (2010).DOI: 10.1520/F1199-88R15.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For A

14、nnual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.3Available from American National Standards Institute (ANSI), 25 W. 43rd St.,4th Floor, New York, NY 10036, http:/www.ansi.org.4Available from Manufacturers Standardization Society of the

15、Valve and FittingsIndustry (MSS), 127 Park St., NE, Vienna, VA22180-4602, http:/www.mss-hq.org.5Available from American Society of Mechanical Engineers (ASME), ASMEInternational Headquarters, Two Park Ave., New York, NY 10016-5990, http:/www.asme.org.Copyright ASTM International, 100 Barr Harbor Dri

16、ve, PO Box C700, West Conshohocken, PA 19428-2959. United States14. Classification4.1 Strainers may be classified into three general construc-tion categories, simplex, duplex (or multiplex), and automatic(self-cleaning), as follows:4.1.1 SimplexA strainer consisting of a single basket orelement cham

17、ber that normally requires the flow through theunit to be shut down before cleaning.4.1.1.1 Classifications of simplex strainers based on portalignment relative to basket or element chamber are Y, T, Z, andothers.4.1.2 Duplex (or Multiplex)A strainer usually consistingof at least two basket or eleme

18、nt chambers separated by a valve(or valving) that permits continuous flow of fluid through onechamber while the other is accessible for cleaning.4.1.3 Automatic (Self-Cleaning)Astrainer providing somemeans for back-flushing or cleaning of the straining elementwhile the unit is in service. It can hav

19、e one or more elementsand may require periodic shutdown for maintenance andinspection.4.2 Strainers may be further classified by pressure ratingsand types of port connections, port alignments relative to unitcenter lines, cover closures, valve types (in duplex), types ofbaskets or elements, material

20、s of construction, and otherfeatures of design.5. Ordering Information5.1 Orders for products under this specification shall includethe following information as applicable. If a manufacturersstandardized product is being ordered, include all data neededby the manufacturer to define the product.5.1.1

21、 Make.5.1.2 Model (simplex or duplex).5.1.3 Port size.5.1.4 Port connections.5.1.5 Maximum allowable pressure/temperature rating.5.1.6 Body and cover material.5.1.7 Type of cover closure.5.1.8 Basket (element) material.5.1.9 Basket hole size.5.1.10 Optional design features.5.1.11 Certification (see

22、8.1.2.1 and Section 9).5.1.12 This ASTM standard designation number.5.1.13 Additional requirements or testing as contracted bythe manufacturer and purchaser.5.2 If a product is to be specified by performance criteriarather than model description, then the following should bespecified:5.2.1 Maximum a

23、llowable clean pressure loss at a givenflow capacity of a given liquid at a given velocity.5.2.2 Temperature and pressure.5.2.3 Straining area.5.2.4 Minimum basket rupture differential pressure (see7.4).5.2.5 Maximum valve seepage rates (see 7.3).5.2.6 Certification (see 6.2, 8.1.2.1, and Section 9)

24、.5.2.7 For self-cleaning strainers, specify basket cleaningeffectiveness and endurance testing.5.3 In general, the standard product description should notbe mixed with the performance criteria because conflictingspecifications can result (for example, maximum allowablepressure loss inconsistent with

25、 product size).6. Materials and Manufacture6.1 Strainer housings, as well as any pressure-retainingparts, including bolting used for pressure retention, shall beconstructed of materials listed in SectionVIII, Division 1 of theASME Boiler and Pressure Vessel Code (hereafter calledASME Code) or ANSI/A

26、SME B31.1. Bolts, screws, andfasteners in contact with interior fluid shall be of appropriatecorrosion-resistant material.6.2 The pressure ratings established under this specificationare based on materials of high quality produced under regularcontrol of chemical and mechanical properties by a recog

27、nizedprocess. The manufacturer shall be prepared to submit acertificate of compliance verifying that his product has been soproduced and that it has been manufactured from materialwhose chemical and mechanical properties are at least equal tothe requirements of the appropriate standard or specificat

28、ion.6.3 For materials not having values of allowable stresstabulated in Section VIII, Division 1 of the ASME Code,allowable stresses shall be determined in accordance with theprocedures outlined in Subsection C and Appendix P of thatsection. Where it can be shown that the values of allowablestress l

29、isted for a particular material in one product form(because of similar chemistry, mechanical properties, heattreatment, and so forth) are applicable to the same material inan unlisted product form, the listed values of allowable stressmay be used.6.4 Seals and parts, other than pressure-retaining pa

30、rts andbolting used for pressure retention, shall be of materialssuitable for the service.6.5 Users are cautioned against applications with fluidswhich may react chemically with any materials used in theseproducts in contact with the fluid.6.6 Cast iron shall be limited to services below 450F(232C).

31、 Cast iron fittings conforming to B16.1 and B16.4 arelimited to Class 125 and Class 250.7. Other Requirements7.1 The maximum allowable working pressure (MAWP)and maximum design temperature (MAT) rating of strainerscovered under this specification shall be established by at leastone of the following

32、methods:7.1.1 Proof test in accordance with the requirements pre-scribed in paragraph UG-101 of Section VIII of the ASMECode. If burst-type tests as outlined in paragraph UG-101(m)are used, it is not necessary to rupture the component. In thiscase, the value of B to be used in determining the MAWP s

33、hallbe the maximum pressure to which the component wassubjected without rupture. Safety of personnel shall be givenserious consideration when conducting proof tests. Compo-nents that have been subjected to a proof test shall not beoffered for sale.F1199 88 (2015)27.1.2 Design calculations in accorda

34、nce with the require-ments prescribed in Section VIII, Division 1 of the ASMECode.7.1.3 Extensive and successful performance experience un-der comparable service conditions with similar materials maybe used as a basis for rating provided all other provisions ofthis specification are met.7.2 Pipe end

35、 connections for strainers shall be in accordancewith one of the standards listed in 2.2 and 2.3 or as agreed uponbetween the purchaser and manufacturer (see 5.1.13).Threaded pipe connections shall be limited to the followingpressures:34 in. (19 mm) NPS and below . . . 1500 psig (10.3 MPa) max1 in.

36、(25 mm) NPS and below . . . 1200 psig (8.27 MPa) max2 in. (50 mm) NPS and below . . . 600 psig (4.14 MPa) max3 in. (76 mm) NPS and below . . . 400 psig (2.76 MPa) max7.3 Duplex (or multiplex) strainer valve seepage rates shallbe minimized to prevent undue spillage of fluid under normaloperating cond

37、itions while the element is being serviced orcleaned in accordance with the manufacturers procedures.Maximum seepage rates with a specified liquid at a specifiedpressure and temperature may be as contracted by the manu-facturer and purchaser (see 5.2.5), and provision may be madeto include a test to

38、 determine acceptability before acceptancefor a given application.7.4 Baskets or elements shall withstand a minimum of10-psi (0.069-MPa) differential pressure without rupturing orsuch other differential pressure as contracted by the manufac-turer and purchaser (see 5.2.4) for the application involve

39、d.8. Test Methods8.1 Test all strainers by one of the following methods:8.1.1 Conduct a hydrostatic test at 112 times the 100F(37C) rated MAWPof the strainer. Perform the test with wateror other liquid having a maximum viscosity of 40 SSU at125F (52C) with a maximum pressure test temperature of125F.

40、 The minimum duration of the test shall be 15 s forstrainers less than 2-in. (50-mm) nominal pipe size (NPS), 1min for strainers 212 through 8 in. (63 through 203 mm), and3 min for larger sizes. The purpose of this test is to detect leaksand structural imperfections. No visible leakage is permitted.

41、8.1.2 Strainers 2-in. (50-mm) NPS and smaller with otherthan flanged connections may, at the option of themanufacturer, be air tested to the lesser of 1.2 times the MAWPor 80 psig (0.55 MPa). The minimum duration of the test shallbe 15 s. Visually detectable leakage is not acceptable.8.1.2.1 If this

42、 option is exercised, the manufacturer shall beable to certify that a prototype of the same size strainer wassubjected to a hydrostatic test in accordance with 8.1.1.9. Certification9.1 When specified in the purchase order or contract, themanufacturers certification shall be furnished to the purchas

43、erstating that samples representing each lot have beenmanufactured, tested, and inspected in accordance with thisspecification and the requirements have been met. Whenspecified in the purchase order or contract, a report of the testresults shall be furnished.10. Product Marking10.1 Each strainer sha

44、ll have a securely attached name plateor other permanent marking indicating:10.1.1 Manufacturers name or trademark.10.1.2 Maximum allowable working pressure.10.1.3 Size (end connection NPS size).10.1.4 Direction of flow (by an arrow or the word “inlet,”“outlet,” or both).10.1.5 ASTM designation of t

45、his specification.11. Quality Assurance11.1 The strainer manufacturer shall maintain the quality ofthe strainers that are designed, tested, and marked in accor-dance with this specification.At no time shall a strainer be soldindicating that it meets the requirements of this specification ifit does n

46、ot meet the requirements herein.12. Keywords12.1 automatic strainer; cast pipe line strainers; cast strain-ers; duplex strainer; simplex strainer; strainer; welded pipe linestrainers; welded strainersASTM International takes no position respecting the validity of any patent rights asserted in connec

47、tion with any item mentionedin this standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the riskof infringement of such rights, are entirely their own responsibility.This standard is subject to revision at any time by the responsib

48、le technical committee and must be reviewed every five years andif not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional standardsand should be addressed to ASTM International Headquarters. Your comments will receive careful con

49、sideration at a meeting of theresponsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you shouldmake your views known to the ASTM Committee on Standards, at the address shown below.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or servi