ANSI ASTM F2880-2014 Standard Specification for Lap-Joint Type Flange Adapters for Polyethylene Pressure Pipe in Nominal Pipe Sizes 3 4 in to 65 in..pdf

1、Designation: F2880 14 An American National StandardStandard Specification forLap-Joint Type Flange Adapters for Polyethylene PressurePipe in Nominal Pipe Sizes34 in. to 65 in.1This standard is issued under the fixed designation F2880; the number immediately following the designation indicates the ye

2、ar oforiginal adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope*1.1 This specification covers the polyethylene material a

3、nddimensions applicable to flange adapters (FAs) used to connectpolyethylene pipes to other flanged pipe and components suchas valves and flanged fittings. This standard describes outsidediameter controlled polyethylene (PE) pipe flange adapters(FAs) in diameters ranging from34 in. through 65 in. (1

4、2 mmthrough 1600 mm). The flange adapters may be manufacturedby various methods including injection molding, compressionmolding, and machining from billet or thick-wall polyethylenepipe.1.2 The flange adapter (FA) is the principal component ofthe lap-joint flanged assembly widely used for several de

5、cadesin low-pressure to high-pressure polyethylene pipe systems forall types of pressurized flow (gas and liquid) applications. Theflange adapters physical shape consists of the pipe-like Neckwhich is monolithic with its Hub. The Neck is intended to bebutt-fused or fusion coupled to the pipe-line; w

6、hile the Hubface is intended to affect the seal when subjected to thedistributed load from the back up ring with its properly torquedbolt-studs and nuts.NOTE 1Polyethylene pipe flange adapters with slip on bolt rings areintended for use being bolted to each other or to be bolted to metal flangeshavi

7、ng (primarily) Class 150 bolt hole patterns such as those presented inmetal flange standards ASME B16.5, ASME B16.47 and AWWA C207.1.3 The values stated in inch-pound units are to be regardedas standard. The values given in parentheses are mathematicalconversions to SI units that are provided for in

8、formation onlyand are not considered standard.1.4 The use of gaskets and gasket selection are often anintegral component of the flange adapter assembly. See thePlastic Pipe Institute Technical Note TN-38 for more informa-tion regarding HDPE flanged joints.1.5 This standard does not purport to addres

9、s all of thesafety concerns, if any, associated with its use. It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use.2. Referenced Documents2.1 ASTM Standards:2D2122 Test Metho

10、d for Determining Dimensions of Ther-moplastic Pipe and FittingsD2513 Specification for Polyethylene (PE) Gas PressurePipe, Tubing, and FittingsD2837 Test Method for Obtaining Hydrostatic Design Basisfor Thermoplastic Pipe Materials or Pressure Design Basisfor Thermoplastic Pipe ProductsD3035 Specif

11、ication for Polyethylene (PE) Plastic Pipe (DR-PR) Based on Controlled Outside DiameterD3261 Specification for Butt Heat Fusion Polyethylene (PE)Plastic Fittings for Polyethylene (PE) Plastic Pipe andTubingD3350 Specification for Polyethylene Plastics Pipe and Fit-tings MaterialsF714 Specification f

12、or Polyethylene (PE) Plastic Pipe (DR-PR) Based on Outside DiameterF2206 Specification for Fabricated Fittings of Butt-FusedPolyethylene (PE)F3034 Specification for Billets made by Winding MoltenExtruded Stress-Rated High Density Polyethylene(HDPE)2.2 ASME Standards:3B16.5 “Pipe Flanges and Flanged

13、Fittings”B16.47 “Large Diameter Steel Flanges: NPS 26 throughNPS 60” Class #150 Series A1This specification is under the jurisdiction of ASTM Committee F17 on PlasticPiping Systems and is the direct responsibility of Subcommittee F17.10 on Fittings.Current edition approved May 1, 2014. Published Jun

14、e 2014. Originallyapproved in 2011. Last previous edition approved in 2011 as F288011a. DOI:10.1520/F2880-14.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the sta

15、ndards Document Summary page onthe ASTM website.3Available from American Society of Mechanical Engineers (ASME), ASMEInternational Headquarters, Three Park Ave., New York, NY 10016-5990, http:/www.asme.org.*A Summary of Changes section appears at the end of this standardCopyright ASTM International,

16、 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United StatesThis international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for theDevelopment of International Standards, Guides an

17、d Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.1B36.10M Welded and Seamless Wrought Steel PipeB36.19M Stainless Steel Pipe2.3 AWWA Standards:4C207 “Standard for Steel Pipe Flanges for WaterworksService, Sizes 4 In. Through 144 In. (100 mm Through

18、3,600 mm) ; Class #150 /Series B,D the outside diameter(OD) of plastic pipe that matches the nominal standarddiameters of metal ductile iron, or, cast-iron pipes; alsocommonly referred to as DIOD, Ductile Iron OutsideDiameter, previously known as CIOD or cast-iron OD.3.1.4 flange adapterOne componen

19、t of the two piecelap-joint flange assembly; It is a one piece polyethylene devicewhose geometry consists of two shapes: the wide, circular,seal-face disk, with central hole, which transitions along itslength into pipe of smaller diameter and wall thickness,matched to the pipe-main to which it is to

20、 be joined. (Refer toFig. 1).3.1.5 HubThe disk ring, or collar, extending radiallyoutward from the pipe OD at the pipe termination.3.1.6 Hydrostatic design stress (HDS)The maximum al-lowable hoop stress in the pipe wall for pipe that is subjectedto sustained long-term hydrostatic pressure. The hydro

21、staticdesign stress is determined by multiplying the hydrostaticdesign basis by the PPI recommended design factor for waterservice. HDS ratings for PE materials are published by PPI inTR-4.3.1.7 IPSIron Pipe Size (steel pipe) outside diameters;replaced with nominal pipe sizes (NPS) per as listed wit

22、h theplastic pipe standards and B36.10M and B36.19M.3.1.8 lap-joint flange ringthe loose metal ring that trans-fers the load from the bolts through the hub to the seal face.4Available from American Water Works Association (AWWA), 6666 W. QuincyAve., Denver, CO 80235, http:/www.awwa.org.5Available fr

23、om NSF International, P.O. Box 130140, 789 N. Dixboro Rd., AnnArbor, MI 48113-0140, http:/www.nsf.org.6Available from Plastics Pipe Institute (PPI), 105 Decker Court, Suite 825,Irving, TX 75062, http:/www.plasticpipe.org.FIG. 1 Polyethylene Flange Adapter GeometryF2880 1423.1.9 neckThe long barrel o

24、f the flange adapter with ODand wall thickness matched to the pipeline dimensions. Theneck length must be sufficient for fusion joining in the fusionmachine used.3.1.10 seal faceThe front of the Hub, which contacts themating flange, which radially confines fluid pressure by com-pressive stress when

25、subjected to distributed load from torquedbolts.3.1.11 residual sealing stressThe long-term compressivestress intensity from the load distributed over the seal face areawhich is in contact with a mating flange.3.1.12 pressure rating (PR)maximum sustained internalwater pressure at 80F (27C) and lower

26、 service temperaturewith specified maximum allowances for pressure surges.PR 52 3HDS 3FTDR 2 1!(1)where:HDS = hydrostatic design stress for water at 73F, psi (kPa)FT= temperature factor (1.00 for 80F (27C) and lowerwater service temperature)DR = dimension ratio. Surge pressure allowances are ap-plie

27、d above the sustained internal pressure and areintegral to the working pressure rating.4. Polyethylene Materials for Flange4.1 GeneralTable 1 contains the list of polyethylenematerials that are acceptable for use in manufacture of theflange adapters. Usually, the flange adapter material has thesame

28、material designation as the specified polyethylene pipe-line material, for the purpose of chemical resistance andheat-fusion joining. Commercial virgin PE material com-pounds shall meet Table 1 physical properties, SpecificationD3350 requirements and shall be classified per SpecificationD3350 as sho

29、wn in Table 1. The PE material compound shallhave HDB ratings at 73F (23C) and at 140F (60C) andHDS ratings at 73F (23C) determined in accordance withTest Method D2837 and PPI TR-3.4.2 ColorThe PE material in the pipe shall contain colorand ultraviolet (UV) stabilizer meeting the requirements ofCode

30、 C or E per Specification D3350. Code C material shallcontain between 2 to 3 percent carbon black by weight.4.3 ReworkClean rework pipe-grade polyethylene mate-rial derived from pipe and or fittings production by the samemanufacturer are acceptable as part of a blend with virginmaterial for the prod

31、uction of flange adapters provided that (a)the cell classification or materials designation code of therework material is the same as the virgin material compound towhich it is added, and (b) the rework materials complied withapplicable requirements as virgin materials.4.4 Potable WaterMaterials use

32、d for products intended foruse in the transport of potable water shall be evaluated andcertified as safe for this purpose by a testing agency acceptableto the local health authority. The evaluation shall be inaccordance with requirements for chemical extraction, taste,and odor that are no less restr

33、ictive than those included inNSF/ANSI Standard No. 14 or NSF/ANSI Standard No. 61.The seal or mark of the laboratory making the evaluationshould be included on the piping per 7.1.3.7.5. Flange Adaptor Dimensions and Working PressureRatings5.1 GeneralThis standard describes 10 dimension ratios(DRs) f

34、or nominal flange adapter sizes ranging from34 in.through 65 in. (12 mm through 1 600 mm). Flange adapteroutside diameters (ODs) conform to the outside diameterdimensions of iron pipe sizes (IPS), or to equivalent outsidediameters for ductile-iron (DI) pipe (DIPS). Polyethyleneflange adapters are cl

35、assified by dimension ratios (DRs)ranging from 7.0 to 32.5. The resultant combinations of PEmaterial designations and DRs define flange adapters withpressure ratings ranging from 40 to 333 psig (276 to 2 299 kPa)when conveying water at 80F (27C) and lower temperatures.Use at temperatures above 80F (

36、27C) up to 140F (60C) isacceptable at pressure ratings that are appropriately reduced forthe service temperature.5.2 Outside diametersThe neck Outside Diameter (OD) ofthe flange adapter measured at 73.4 6 3.6F (23 6 2C) shallconform to the applicable OD dimension requirements speci-fied in the relat

37、ed polyethylene pipe standards : SpecificationsTABLE 1 Property Values and Specification D3350 Cell Classification for MaterialsPropertyMaterials Designation CodePE2606 PE2706 PE2708APE3608APE3708 PE3710 PE4608 PE4708 PE4710AProperty ValuesHDB at 140F (60C) per ASTM D 2837 and PPI TR-3, psi(MPa)CCCC

38、CCCCCHDS at 73F (23C) per ASTM D 2837 and PPI TR-3, psi(MPa)630 (4.6) 630 (4.6) 800 (5.5) 800 (5.5) 800 (5.5) 1000(6.9)800 (5.5) 800 (5.5) 1000(6.9)Specification D3350 Cell ClassificationBValuesDensity (natural base resin) 2 2 2 3 3 3 4 4 4Melt Index 3-4 3-4 3-4 4 4 4 4 4 4Flexural Modulus 3-4 3-4 3

39、-4 $4 $4 $4 $4 $4 $5Tensile Strength at Yield $3 $3 $3 $4 $4 $4 $4 $4 $4SCG Resistance 6 7 7 6 7 7 6 7 7Hydrostatic Strength Classification 3 3 3 4 4 4 4 4 4ColorandUVStabilizer CorE CorE CorE CorE CorE CorE CorE CorE CorEAHDB at 140F (60C) per ASTM D2837 and PPI TR-3 at 140F required; contact manuf

40、acturer for listed value.BSpecification D3350 cell classification values reflect typical property values for numerous lots of the material and do not include variability in testing or manufacturingtolerances. Values for individual material lots can vary from typical values. Contact the manufacturer

41、for information about variability in testing and material manufacturingtolerances.F2880 143F714, D2513, D3035, and AWWA C901 and C906. Measure-ments shall be made according to the methods specified in TestMethod D2122. The tolerance on outside diameter shall notexceed 60.45 percent of the average ou

42、tside diameter, aspresented in the tables for NPS 4-in. and larger.5.2.1 Special SizesWhere existing system conditions orspecial local requirement make other diameters or dimensionratios necessary, other sizes or dimension ratios, or both, shallbe acceptable for engineered applications when mutually

43、agreed upon by the customer and the manufacturer, if theflange adapter is manufactured from plastic compounds meet-ing the material requirements of this specification, and thestrength and design requirements are calculated on the samebasis as those use in this specification. For diameters not showni

44、n Table 2, Table 3 or Table 4, the tolerance shall be the samepercentage as that shown in the corresponding tables for thenext smaller listed size.5.3 Neck Wall thicknessThe flange adapter manufacturermay provide extra wall thickness to compensate for PE pipetoe-in, out of round, and pipe over-wall.

45、 Wall thicknesstolerance above minimum wall as measured and calculatedaccording to Test Method D2122 in any diametrical crosssection of the pipe shall not exceed 17 percent. The flangeadapters minimum neck wall thickness measured at 73.4 63.6F (23 6 2C) shall conform to the applicable pipe stan-dard

46、s tabulated wall DR dimension, with a wall thicknesstolerance of - zero, + 17% min. wall. The minimum wallthickness by pipe OD and sizing system (IPS consult Flange Adapter manufacturer.Minimum Neck LengthNominal Pipe Size IPS DIPS DR 7 DR 9 DR 11 -DR 32.534 in. X 2.88 2.88 2.881 in X 3.75 3.75 3.75

47、114 in. X 3.88 3.88 3.88112 in. X 4.00 4.00 4.002 in. X 4.25 4.25 4.253 in. X 4.50 4.50 4.504 in. X X 5.38 5.38 6.005 in. X 6.50 6.50 6.506 in. X X 6.75 6.75 6.758 in. X X 6.50 613 6.1310 in. X X 6.50 6.13 6.1312 in. X X 7.38 7.38 7.7514 in. X X 8.13 7.75 7.7516in. X X 8.44 8.00 8.0018 in. X X 8.50

48、8.13 8.1320 in. X X 8.94 8.38 8.3822 in. X 9.03 8.63 8.6324 in. X X 9.50 8.69 8.6926 in. X 10.38 10.13 10.1328 in. X 10.63 10.25 10.1330 in. X X 10.88 10.38 10.2532 in. X 11.13 10.88 10.7534 in. X 12.13 11.50 10.8836 in. X X 13.13 12.19 11.311000mm / 40 in. X * * 12.6342 in. X X * * 12.6348 in. X X

49、* * 12.8854 in. X * * 20.131400mm /55 in. * * 20.5063 in. X * * 20.5065 in. X * * 21.50F2880 144Hub Wall shall be sufficiently dimensioned to provide a DRpressure rating at least equal to that of the pipe DR to which thebutterfly flange adapter will be joined by heat fusion. If thetapered Hub Wall at the seal face is not sufficiently thick tomatch the pipe pressure rating, then a sufficiently thickcorrosion resistant metal collar shall be snug-fit over the hubstaper transition section to reinforce the taper porti