ANSI ASTM F2983-2013 Standard Guide for Manufacturers for Labeling and Care Instructions for Wrestling Mats《摔跤垫标签和清洁养护用制造商指南》.pdf

1、Designation: F2983 13 An American National StandardStandard Guide forManufacturers for Labeling and Care Instructions forWrestling Mats1This standard is issued under the fixed designation F2983; the number immediately following the designation indicates the year oforiginal adoption or, in the case o

2、f revision, the year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope1.1 This guide sets forth labeling and instruction guidelinesfor manufacturers of wrestling mats.1

3、.2 This guide applies only to wrestling mats whose stan-dard specifications are under auspices of ASTM CommitteeF08.1.3 This standard does not purport to address all of thesafety concerns, if any, associated with its use. It is theresponsibility of the user of this standard to establish appro-priate

4、 safety and health practices and determine the applica-bility of regulatory limitations prior to use.2. Referenced Documents2.1 ASTM Standards:2F1081 Specification for Competition Wrestling Mats3. Terminology3.1 Definitions:3.1.1 accompanying literature, nprinted material that ac-companies the produ

5、ct when it is sold or distributed.3.1.2 caution, nsignal word used to indicate a potentiallyhazardous situation that, if not avoided, may result in injury ordeath.3.1.3 contact information, ninformation that allows theuser to contact the manufacturer of the product, such as name,telephone number, we

6、bsite address.3.1.4 danger, nsignal word used to alert the user to animminently hazardous situation that, if not avoided, will resultin serious injury or death and this signal word is to be limitedto the most extreme situations.3.1.5 label, nprinted material that is physically attached tothe wrestli

7、ng mat in a durable fashion.3.1.6 label material, nsubstrate paper, fabric, ink, paint orother material from which the label is made.3.1.7 manufacturer, nentity responsible for marketing theproduct.3.1.8 mat, nshock absorbing material that meets Specifi-cation F1081.3.1.8.1 DiscussionMay or may not

8、be coated or incorpo-rate a cover (example: fabric).3.1.9 mounting location, nposition on the mat in whichinformation may be affixed.3.1.10 pictogram, ngraphic representation that depicts orillustrates an act or condition without the use of accompanyingwriting.3.1.11 signal word, nword that conveys

9、a level of dangercommensurate with the risk of injury.3.1.12 warning, nsignal word used to indicate a poten-tially hazardous situation that, if not avoided, could result indeath or serious injury.3.2 Definitions of Terms Specific to This Standard:3.2.1 date of manufacture, nuncoded four-digit year d

10、ur-ing which the wrestling mat was manufactured.3.2.2 durable, adjlabel should be designed to be legible aslong as the manufacturers logo remains legible.4. Significance and Use4.1 This guide gives guidelines for labels and instructions tomanufacturers that manufacture wrestling mats.4.2 The purpose

11、 of the labels and instructions is to help alertand remind users of important issues related to wrestling matsand their use.4.3 LimitationThis guide applies only to wrestling matswhose standard specifications are under auspices of ASTMCommittee F08.5. Wrestling Mat Labeling Requirements5.1 Required

12、information shall be on one or more labels thatare affixed to the wrestling mat in a durable fashion. The labelsshall have:5.1.1 Manufacturer IdentificationFull name.1This guide is under the jurisdiction of ASTM Committee F08 on SportsEquipment, Playing Surfaces, and Facilities and is the direct res

13、ponsibility ofSubcommittee F08.12 on Gymnastics and Wrestling Equipment.Current edition approved July 1, 2013. Published August 2013. DOI: 10.1520/F2983-13.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of AST

14、MStandards volume information, refer to the standards Document Summary page onthe ASTM website.Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States15.1.2 Manufacturer Contact InformationAt least one ofthe following shall be provided: (1) t

15、oll-free phone number, (2)mailing address, (3) website, or (4) e-mail address for customerservice.5.1.3 Instruct user that the mat is only to be used under thesupervision of trained and qualified instructors.5.1.4 Warn users that they should follow progressive wres-tling training practices.5.1.5 War

16、n users and instructors of this mat to make surethat they have allowed enough space to properly and safelyperform the chosen maneuvers on the mat.5.1.6 Perform all maneuvers so as to avoid contact withinstructors, bystanders or other users, and to avoid goingoutside the perimeter of this mat.5.1.7 M

17、at protection may vary according to room tempera-ture and age.5.1.8 Tape or secure mats properly prior to every use tominimize movement during use.5.1.9 Instruction to read owners manual/manufacturersinstructions.6. Accompanying Literature Requirements6.1 Accompanying literature can be on product pa

18、ckaging,in instructions included with the product, and so forth. Theaccompanying literature shall have:6.1.1 Care instructions such as:6.1.1.1 Cleaning instructions.6.1.1.2 When to replace or recondition.6.1.1.3 What materials can damage the mat.6.1.1.4 Pre-use inspection.6.1.1.5 Proper storage and

19、handling of the mat.6.1.2 Warranty or where warranty can be accessed (websiteor equivalent).6.1.3 Manufacturer IdentificationFull name of manufac-turer including any other information needed to identify theresponsible entity.6.1.4 Manufacturer Contact InformationWebsite address,mailing address, and

20、e-mail address for customer service.6.1.5 Statement to read and always comply with manufac-turers instructions.6.1.6 Statement to always comply with rules of applicablesports or activities.7. Keywords7.1 wrestling matsBibliography(1) ASTM F381, Standard Safety Specification for Components,Assembly,

21、Use, and Labeling of Consumer Trampolines(2) ASTM F1749, Standard Specification for Fitness Equipment andFitness Facility Safety Signage and Labels(3) ASTM F2041, Standard Specification for Paintball Marker Warn-ings(4) ANSI Z535.6, American National Standard for Product Safety(5) CPSC: 16 CFR Part

22、1203, Safety Standard for Bicycle Helmets(6) NOCSAE: ND-001, Standard Drop Test Method and EquipmentUsed in Evaluating the Performance Characteristics of ProtectiveHeadgear(7) FMVSS 218: Federal Motor Vehicle Safety Standard No. 218(Motorcycle Helmets)(8) ISO 3864-2, Graphical symbols - Safety colou

23、rs and safety signs- Part 2: Design principles for product safety labelsASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentionedin this standard. Users of this standard are expressly advised that determination of the validity of

24、 any such patent rights, and the riskof infringement of such rights, are entirely their own responsibility.This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years andif not revised, either reapproved or withdrawn. Your comments ar

25、e invited either for revision of this standard or for additional standardsand should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of theresponsible technical committee, which you may attend. If you feel that your comments have not rec

26、eived a fair hearing you shouldmake your views known to the ASTM Committee on Standards, at the address shown below.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies)

27、of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org). Permission rights to photocopy the standard may also be secured from the ASTM website (www.astm.org/COPYRIGHT/).F2983 132