ANSI ASTM F420-2004 Standard Test Method for Access Depth Under Furniture of Vacuum Cleaners.pdf

1、Designation: F420 04 (Reapproved 2014) An American National StandardStandard Test Method forAccess Depth Under Furniture of Vacuum Cleaners1This standard is issued under the fixed designation F420; the number immediately following the designation indicates the year of originaladoption or, in the cas

2、e of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A superscriptepsilon () indicates an editorial change since the last revision or reapproval.1. Scope1.1 This test method covers the measurement of the opera-tional ability of the vacuum cleaner,

3、expressed as the accessdepth for a given furniture clearance above the floor.1.2 This test method can be used in testing household andcommercial vacuum cleaners.1.3 The values stated in inch-pound units are to be regardedas standard. The values given in parentheses are mathematicalconversions to SI

4、units that are provided for information onlyand are not considered standard.1.4 This standard does not purport to address all of thesafety concerns, if any, associated with its use. It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and determi

5、ne the applica-bility of regulatory limitations prior to use.2. Summary of Test Method2.1 The carpet nozzle is inserted under a horizontal rod andthe access depth is measured from the front of the rod.3. Significance and Use3.1 This test method is intended to provide a means ofevaluating the effecti

6、ve cleaning depth under furniture.3.2 Results of testing by this test method can be used as abasis for specifications on cleaning under furniture.4. Apparatus4.1 A 0.75-in. (19-mm) diameter rod, mounted horizontallyin a suitable supporting device to provide heights under the rodfrom 0 to 10.0 in. (0

7、 to 254 mm) in increments of 0.5 in. (12.7mm).4.2 A device for measuring access depth, (in inches ormillimetres) horizontally from the face of the horizontal bar in4.1.4.3 Voltage Regulator System, to control the input voltage tothe vacuum cleaner. The regulator system must be capable ofmaintaining

8、the vacuum cleaners rated voltage 61 % andrated frequency having a wave form that is essentially sinusoi-dal with 3 % maximum harmonic distortion for the duration ofthe test.4.4 Voltmeter, to measure input voltage to the vacuumcleaner, to provide measurements accurate to within 61%.5. Sampling5.1 Th

9、e access depth under furniture shall be established onthree samples.6. Preparation of Apparatus6.1 Prepare the apparatus as shown in Figs. 1-3.7. Procedure7.1 Upright Vacuum Cleaners (Fig. 1):7.1.1 Place the upright vacuum cleaner in its most advanta-geous position for cleaning under furniture. Oper

10、ate thevacuum cleaner at the vacuum cleaners nameplate ratedvoltage 61 % and rated frequency 61 Hz with the nozzleheight in the lowest cleaning position on a bare floor surface.7.1.1.1 For vacuum cleaners with dual nameplate voltageratings, conduct the test method at the highest voltage.7.1.2 The ac

11、cess depth is the distance (in inches or milli-metres) measured from the front of the 0.75-in. (19-mm)diameter rod (when in contact with the highest component ofthe vacuum cleaner) to the most advanced point of the inlet ofthe nozzle.NOTE 1If the access depth is influenced by the cleaner bag, nopres

12、sure is to be applied to the handle or the bag to reduce the height.NOTE 2The vacuum cleaner must be energized, if a soft bag ispresent, as the inflation changes the working height of the handle when itis in its lowest position. If there is no soft bag, or no inflation possible,there is no reason to

13、 energize the cleaner as the test is conducted on a barefloor surface and the nozzle suction will be at a minimum and have littleeffect on the nozzle down-force.7.1.3 Measure the access depth for heights from 0 to 10 in.(0 to 254 mm) in 0.5-in. (12.7-mm) increments. If full insertionof the cleaning

14、mechanism occurs before 10.0 in. (254 mm),record this height. Cleaning mechanism refers to all of the partsfrom the vacuum cleaner nozzle to and including the handlegrip.1This test method is under the jurisdiction of ASTM Committee F11 on VacuumCleaners and is the direct responsibility of Subcommitt

15、ee F11.20 on Performance(Test Methods).Current edition approved Nov. 1, 2014. Published November 2014. Originallyapproved in 1975. Last previous edition approved in 2009 as F420 04 (2009).DOI: 10.1520/F0420-04R14.Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA

16、 19428-2959. United States17.2 Combination and Canister Vacuum Cleaners (Fig. 2 andFig. 3):7.2.1 Place the combination or canister vacuum cleanernozzle in its most advantageous position for cleaning underfurniture. Operate the vacuum cleaner at the vacuum cleanersnameplate rated voltage 61 % and rat

17、ed frequency 61 Hz withthe nozzle in full contact with the bare floor surface or thelowest nozzle setting.7.2.2 Vacuum Cleaner Nozzle Perpendicular to VacuumCleaner (Fig. 2)The access depth is the distance (in inches ormillimetres) measured from the front of the 0.75-in. (19-mm)diameter rod (when in

18、 contact with the highest component ofthe cleaning system) to the most advanced point of the inlet ofthe nozzle when the front edge of the nozzle is perpendicularto the vacuum cleaner in its most advantageous position forcleaning under furniture.7.2.3 Vacuum Cleaner Nozzle Not Perpendicular to Vacuu

19、mCleaner (Fig. 3)The access depth is the distance (in inches ormillimetres) measured from the front of the 0.75-in. (19-mm)diameter rod (when in contact with the highest component ofthe cleaning system) to a line parallel to the rod and through thecenter line of the nozzle and front opening.7.2.4 Me

20、asure the access depth for heights from 0 to 10 in.(0 to 254 mm) in 0.5-in. (12.7-mm) increments. If full insertionof the cleaning mechanism occurs before 10.0 in. (254 mm),record this height. Cleaning mechanism refers to all of the partsfrom the vacuum cleaner nozzle to and including the hose orwan

21、d grip.8. Report8.1 The report shall include a table and a plotted curveindicating the clearance above the floor (in inches or millime-tres) and the access depth (in inches or millimetres).9. Precision and Bias9.1 No justifiable statements can be made on precision (orbias) of this test method since

22、the method determines whetheror not an attribute is present.FIG. 1 Access Depth for Upright Vacuum CleanersFIG. 2 a, b Access Depth for Combination and Canister Vacuum Cleaners (Nozzle Perpendicular to Vacuum Cleaner)FIG. 3 Access Depth for Combination and Canister Vacuum Cleaners (Nozzle Not Perpen

23、dicular to Vacuum Cleaner)F420 04 (2014)210. Keywords10.1 access depth; furniture; vacuum cleanerASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentionedin this standard. Users of this standard are expressly advised that determi

24、nation of the validity of any such patent rights, and the riskof infringement of such rights, are entirely their own responsibility.This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years andif not revised, either reapproved or wi

25、thdrawn. Your comments are invited either for revision of this standard or for additional standardsand should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of theresponsible technical committee, which you may attend. If you feel that y

26、our comments have not received a fair hearing you shouldmake your views known to the ASTM Committee on Standards, at the address shown below.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (si

27、ngle or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org). Permission rights to photocopy the standard may also be secured from the Copyright Clearance Center, 222Rosewood Drive, Danvers, MA 01923, Tel: (978) 646-2600; http:/ 04 (2014)3