ANSI ASTM F823-1993 Standard Specification for Desk Log Marine Steel with Cabinet《带客舱的甲板和计程仪的船用钢规范》.pdf

1、Designation: F823 93 (Reapproved 2017) An American National StandardStandard Specification forDesk, Log, Marine, Steel, with Cabinet1This standard is issued under the fixed designation F823; the number immediately following the designation indicates the year of originaladoption or, in the case of re

2、vision, the year of last revision. A number in parentheses indicates the year of last reapproval. A superscriptepsilon () indicates an editorial change since the last revision or reapproval.1. Scope1.1 This specification covers the construction of marine logdesks of steel construction with cabinets.

3、1.2 The values stated in inch-pound units are to be regardedas standard. The values given in parentheses are mathematicalconversions to SI units that are provided for information onlyand are not considered standard.2. Referenced Documents2.1 ASTM Standards:2A366/A366M Specification for Commercial St

4、eel (CS)Sheet, Carbon, (0.15 Maximum Percent) Cold-Rolled(Withdrawn 2000)3D907 Terminology of AdhesivesF782 Specification for Doors, Furniture, MarineF825 Specification for Drawers, Furniture, Marine, SteelF826 Specification for Tops, Furniture, Marine, Steel2.2 AISC Manual:4AISC Wire and Sheet Meta

5、l Gauges Equivalent Thickness inDecimals of an Inch, U.S. Standard Gauge (USSG) forUncoated Hot and Cold Rolled Sheets3. Terminology3.1 Definitions of Terms Specific to This Standard:3.1.1 log desk with cabineta desk with attached cabinetlocated in various places aboard ship for making records andfo

6、r storage. Log desk has a drawer with a writing surface at thetop and a cabinet with adjustable shelves and doors below.4. Ordering Information4.1 Orders for items purchased under this specification shallinclude the following information:4.1.1 Quantity.4.1.2 Paint:4.1.2.1 ColorPurchaser shall pick f

7、rom manufacturerssamples or submit sample chip of color desired.4.1.2.2 Manufacturers standard baked enamel will be fur-nished unless otherwise required and indicated by the pur-chaser.4.1.3 Options for Tops:4.1.3.1 Unless otherwise specified in the orderingdocuments, the top supplied by the furnitu

8、re manufacturer maybe, at his option, Type I, II, III, or IV in accordance withSpecification F826.4.1.3.2 Color or pattern of top covering material shall bespecified.4.1.4 Options for DrawersDrawer locks shall be fur-nished only when specified in ordering documents. Masterkeying of drawer locks will

9、 not be provided unless requiredand defined by the ordering documents. See Specification F825for lock description.4.1.5 Options for DoorsDoor locks shall be furnishedonly when specified in ordering documents. Master keying ofdoor locks will not be provided unless required and defined inthe ordering

10、documents. Doors shall be Type I in accordancewith Specification F782.4.1.6 If the total weight of the chest of drawers is requiredit shall be requested by the purchaser.5. Materials and Manufacture5.1 For typical design, see Fig. 1.5.2 Sheet metal shall be in accordance with SpecificationA366/A366M

11、, commercial quality.5.2.1 Minimum sheet metal thickness shall be:5.2.1.1 Sides and front rails 18 USSG (0.0478 in. or 1.2mm).5.2.1.2 Back 20 USSG (0.0359 in. or 0.9 mm).5.2.1.3 Base frame 16 USSG (0.0598 in. or 1.5 mm).5.3 Joining of Metal Components:5.3.1 Metal components shall be joined by weldin

12、g orgluing with a structural adhesive as defined in TerminologyD907. The back panel may be riveted to case provided rivetsare not visible after installation.5.3.2 Joining shall be adequate to prevent racking of chestduring handling.1This specification is under the jurisdiction of ASTM Committee F25

13、on Shipsand Marine Technology and is the direct responsibility of Subcommittee F25.03 onOutfitting and Deck Machinery.Current edition approved Jan. 1, 2017. Published January 2017. Originallyapproved in 1983. Last previous edition approved in 2010 as F823 93 (2010).DOI: 10.1520/F0823-93R17.2For refe

14、renced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.3The last approved version of this historical standard is referenced o

15、nwww.astm.org.4Available from American Institute of Steel Construction (AISC), 130 E.Randolph St., Suite 2000, Chicago, IL 60601-6219, http:/www.aisc.org.Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United StatesThis international standard was d

16、eveloped in accordance with internationally recognized principles on standardization established in the Decision on Principles for theDevelopment of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.15.3.3 Spotwelds

17、 shall be spaced approximately 3 in. (76mm) on centers.5.3.4 Visible spotwelds, higher than the general surface ofthe adjacent metal, shall be ground flush.5.3.5 Visible spotweld depressions shall be spot filled andsanded flush.5.4 Side panels shall be stiffened suitably to prevent buck-ling or oil-

18、canning.5.5 Sound deadening shall be vermin proof and applied toback and inner face of sides of chest. Location and thickness ofapplied sound deadener shall be as required to sound-deadenchest.5.6 Top shall be manufactured in accordance with Specifi-cation F826.5.7 Drawers shall be manufactured in a

19、ccordance withSpecification F825.5.8 Doors shall be Type I, Grade A and shall be manufac-tured in accordance with Specification F782.5.9 Cabinet section shall be provided with two adjustableshelves.5.10 Top shall be provided with a pencil tray along backedge.5.11 A furniture base shall be provided s

20、uitable for securinglog desk to deck.6. Performance Requirements6.1 The completed log desk with cabinet, with top, drawers,and doors installed, shall satisfy the corresponding perfor-mance requirements outlined in Specifications F826, F825, andF782.7. Dimensions7.1 For dimensions, see Table 1.8. Wor

21、kmanship, Finish, and Quality Assurance8.1 All workmanship and material shall be of specifiedquality in keeping with the best commercial marine practice soas to produce each item suitable for its intended use.8.2 All exposed burrs, raw or sharp edges which might beinjurious to personnel shall be rem

22、oved.8.3 Depressions considered unacceptable for products enduse shall be spot filled and sanded smooth.8.4 Finish:8.4.1 All steel surfaces unless corrosion resistant or with acorrosion-resistant plating shall be painted so as to preventcorrosion.NOTE 1For description of Type I, II, III, and IV tops

23、, see Specification F826.NOTE 2For description of drawers, see Specification F825.NOTE 3For description of Type I doors and available alternates, see Specification F782.NOTE 4If log desk is located in a corner, Dimension “F” next to this adjacent wall shall be 0 in. (0 mm). In all other cases, the m

24、inimum value forDimension “F” shall be34 in. (19.05 mm).NOTE 5The minimum value for Dimension “H” shall be 4 in. (102 mm).FIG. 1 Log Desk with CabinetF823 93 (2017)28.4.2 Unless otherwise required by the ordering documents,all parts normally visible on the completed unit shall have themanufacturers

25、standard baked-on enamel finish.8.4.3 Color to be specified in the ordering documents.9. Inspection and Certification9.1 Manufacturer shall inspect and certify that the item offurniture complies with the furniture specification and theloading requirements as defined in Section 6.10. Packaging and Pa

26、ckage Marking10.1 Each item shall be marked in accordance with thepurchase order.10.2 Packaging shall be provided and shall be acceptable toa common carrier.11. Keywords11.1 cabinets; log desks; marine furniture; marine log desks;steel log desksASTM International takes no position respecting the val

27、idity of any patent rights asserted in connection with any item mentionedin this standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the riskof infringement of such rights, are entirely their own responsibility.This standard is sub

28、ject to revision at any time by the responsible technical committee and must be reviewed every five years andif not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional standardsand should be addressed to ASTM International Headqua

29、rters. Your comments will receive careful consideration at a meeting of theresponsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you shouldmake your views known to the ASTM Committee on Standards, at the address shown below.This standa

30、rd is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serv

31、iceastm.org (e-mail); or through the ASTM website(www.astm.org). Permission rights to photocopy the standard may also be secured from the Copyright Clearance Center, 222Rosewood Drive, Danvers, MA 01923, Tel: (978) 646-2600; http:/ 1 Dimensions of Log Desk with CabinetDesignationin. mmDimension Tole

32、rance To + Or Dimension Tolerance To + Or Width A 30116 762 2Height B 42116 1067 2Depth C 24116 610 2Drawer section overhang D 558116 143 2Toespace,front,E 3 max116 76 max 2Toespace,side,AF 4 max116 102 max 2Drawer section height G 7 max116 178 max 2BaseheightBH 434 max116 121 max 2AIf log desk is located in a corner, Dimension F next to this adjacent wall shall be 0 in. (0 mm). In all other cases, the minimum value for Dimension F shall be34 in. (19mm).BThe minimum value for Dimension H shall be 4 in. (120 mm).F823 93 (2017)3