ANSI AWS B2.1-1 8-229-2002 Standard Welding Procedure Specification (SWPS) for Gas Tungsten Arc Welding followed by Shielded Metal Arc Welding of Carbon Steel (M-1 P-1 S-1 Groups 1.pdf

1、AWS B2.1-1/8-229:2002-AMD1 (R2013)An American National Standardthird printing, September 2010Standard Welding ProcedureSpecification (SWPS) forGasTungsten Arc Weldingfollowed by ShieldedMetal Arc Welding ofCarbon Steel (M-1/P-1,Groups1or2)toAustenitic StainlessSteel (M-8/P-8, Group 1),1/8 through 1-

2、1/2 inchThick, ER309(L) andE309(L)-15, -16, or -17,As-Welded Condition,Primarily Pipe ApplicationsSite LicenseAWS B2.1-1/8-229:2002-AMD1 (R2013)An American National StandardApproved by theAmerican National Standards InstituteAugust 28, 2002Amended: September 8, 2010Reaffirmed: March 11, 2013Standard

3、 Welding Procedure Specification (SWPS) forGas Tungsten Arc Welding followed by Shielded MetalArc Welding of Carbon Steel (M-1/P-1, Groups 1 or 2)to Austenitic Stainless Steel (M-8/P-8, Group 1),1/8 through 1-1/2 inch Thick, ER309(L) andE309(L)-15, -16, or -17, As-Welded Condition,Primarily Pipe App

4、lications1st EditionPrepared by theAmerican Welding Society (AWS) B2 Committee on Procedure and Performance QualificationUnder the Direction of theAWS Technical Activities CommitteeApproved by theAWS Board of DirectorsAbstractThis standard contains the essential welding variables for welding carbon

5、steel to austenitic stainless steel in the thick-ness range of 1/8 through 1-1/2 inch, using manual gas tungsten arc welding followed by shielded metal arc welding. Itcites the base metals and operating conditions necessary to make the weldment, the filler metal specifications, and theallowable join

6、t designs for groove and fillet welds. This SWPS was developed primarily for pipe applications.AWS B2.1-1/8-229:2002-AMD1 (R2013)International Standard Book Number: 0-87171-708-5American Welding Society8669 Doral Blvd., Suite 130, Doral, FL 33166 2002 by American Welding SocietyAll rights reservedPr

7、inted in the United States of AmericaReprinted: May 2006Amended: 3rd Printing, September 8, 2010Reaffirmed: March 11, 2013iiAWS B2.1-1/8-229:2002-AMD1 (R2013)Statement on the Use of American Welding Society StandardsAll standards (codes, specifications, recommended practices, methods, classification

8、s, and guides) of the AmericanWelding Society (AWS) are voluntary consensus standards that have been developed in accordance with the rules of theAmerican National Standards Institute (ANSI). When AWS American National Standards are either incorporated in, ormade part of, documents that are included

9、 in federal or state laws and regulations, or the regulations of other govern-mental bodies, their provisions carry the full legal authority of the statute. In such cases, any changes in those AWSstandards must be approved by the governmental body having statutory jurisdiction before they can become

10、 a part ofthose laws and regulations. In all cases, these standards carry the full legal authority of the contract or other documentthat invokes the AWS standards. Where this contractual relationship exists, changes in or deviations from requirementsof an AWS standard must be by agreement between th

11、e contracting parties.AWS American National Standards are developed through a consensus standards development process that bringstogether volunteers representing varied viewpoints and interests to achieve consensus. While AWS administers theprocess and establishes rules to promote fairness in the de

12、velopment of consensus, it does not independently test, evalu-ate, or verify the accuracy of any information or the soundness of any judgments contained in its standards.AWS disclaims liability for any injury to persons or to property, or other damages of any nature whatsoever, whetherspecial, indir

13、ect, consequential, or compensatory, directly or indirectly resulting from the publication, use of, or relianceon this standard. AWS also makes no guarantee or warranty as to the accuracy or completeness of any informationpublished herein.In issuing and making this standard available, AWS is neither

14、 undertaking to render professional or other services for oron behalf of any person or entity, nor is AWS undertaking to perform any duty owed by any person or entity to someoneelse. Anyone using these documents should rely on his or her own independent judgment or, as appropriate, seek theadvice of

15、 a competent professional in determining the exercise of reasonable care in any given circumstances. It isassumed that the use of this standard and its provisions is entrusted to appropriately qualified and competent personnel.This standard may be superseded by new editions. This standard may also b

16、e corrected through publication of amendmentsor errata or supplemented by publication of addenda. Information on the latest editions of AWS standards includingamendments, errata, and addenda is posted on the AWS web page (www.aws.org). Users should ensure that they have thelatest edition, amendments

17、, errata, and addenda.Publication of this standard does not authorize infringement of any patent or trade name. Users of this standard acceptany and all liabilities for infringement of any patent or trade name items. AWS disclaims liability for the infringement ofany patent or product trade name res

18、ulting from the use of this standard.AWS does not monitor, police, or enforce compliance with this standard, nor does it have the power to do so.Official interpretations of any of the technical requirements of this standard may only be obtained by sending a request,in writing, to the appropriate tec

19、hnical committee. Such requests should be addressed to the American Welding Society,Attention: Managing Director, Technical Services Division, 8669 Doral Blvd., Suite 130, Doral, FL 33166 (see Annex A).With regard to technical inquiries made concerning AWS standards, oral opinions on AWS standards m

20、ay be rendered.These opinions are offered solely as a convenience to users of this standard, and they do not constitute professionaladvice. Such opinions represent only the personal opinions of the particular individuals giving them. These individualsdo not speak on behalf of AWS, nor do these oral

21、opinions constitute official or unofficial opinions or interpretations ofAWS. In addition, oral opinions are informal and should not be used as a substitute for an official interpretation.This standard is subject to revision at any time by the AWS B2 Committee on Procedure and Performance Qualificat

22、ion.It must be reviewed every five years, and if not revised, it must be either reaffirmed or withdrawn. Comments (recommen-dations, additions, or deletions) and any pertinent data that may be of use in improving this standard are required andshould be addressed to AWS Headquarters. Such comments wi

23、ll receive careful consideration by the AWS B2 Committeeon Procedure and Performance Qualification and the author of the comments will be informed of the Committeesresponse to the comments. Guests are invited to attend all meetings of the AWS B2 Committee on Procedure and Perfor-mance Qualification

24、to express their comments verbally. Procedures for appeal of an adverse decision concerning all suchcomments are provided in the Rules of Operation of the Technical Activities Committee. A copy of these Rules can beobtained from the American Welding Society, 8669 Doral Blvd., Suite 130, Doral, FL 33

25、166.iiiAWS B2.1-1/8-229:2002-AMD1 (R2013)Personnel (Reaffirmation)AWS B2 Committee on Procedure and Performance QualificationJ. J. Fluckiger, Chair Idaho National LaboratoryJ. L. Cooley, 1st Vice Chair J. C. it is necessary to have at least a 6-volume change of atmo-sphere within the purge zone prio

26、r to welding. As an alternative, theoxygen content of the purge zone shall be equal to 2% or less, asmeasured with on oxygen analyzer, prior to welding. It is not neces-sary to shield the root of fillet welds or groove welds with backing orback gouging.Flow Rate: A typical flow range of 5 ft3/h to 1

27、5 ft3/h may be varied depending oncomponent configuration. Torch Gas Nozzle Size: 1/4 in to 3/4 in inside diameter.Trailing Gas: NoneTUNGSTEN ELECTRODESType: AWS A5.12 or ASME SFA 5.12, EWTh-2, EWCe-2, or EWLa-1.5Size: 1/16 in through 1/8 in diameter sharpened to a point.POSTWELD HEAT TREATMENTPostw

28、eld Heat Treatment: None (Not qualified for PWHT applications)TECHNIQUEWeave or Stringer Bead: EitherPeening: Not permittedInitial Cleaning: Chemical or mechanical; joint shall be dry prior to welding.Interpass Cleaning: Mechanical onlyBackGouging: Not required, mechanical or thermal when used.Singl

29、e or Multiple Passes: MultipleMaximum Bead Thickness: 1/4 inRepair: Defects in welds shall be removed by mechanical or thermal meth-ods. The repair cavity may differ in contour and dimension from anormal joint preparation and may present different restraint condi-tions. Repair of base metal defects

30、shall be in accordance with therequirements of the fabrication document(s).Permission to reproduce for intra-company use only is granted by the American Welding SocietyStandard Welding Procedure Specification (SWPS)AWS B2.1-1/8-229:2002-AMD1 (2013)Page 4 of 17ELECTRICAL CHARACTERISTICSaThe care and

31、storage of electrodes shall be as recommended by the electrode manufacturer.bValues not to exceed capacity of tungsten electrodes.cAn additional layer is optional.dXX Coating Type 15, -16, and -17 are acceptable.eBacking rings may be used when permitted by the fabrication document(s).fFlat and horiz

32、ontal positions only.Pulsing Current: Not permittedCOMPANY NAME _In the name of the Company stated above, I accept full responsibility for the application of this SWPS for usewith:_ Dated _Fabrication Document(s): (Such as Code, Specification, or Contract Document)Date _ Approved by _ Title _GROOVE

33、WELDSFiller Metal CurrentLayer ClassificationaDia. (in) AmperesbPolarityRootcRootcRootcBalanceBalanceBalanceBalanceER309(L)ER309(L)ER309(L)E309(L)-XXdE309(L)-XXE309(L)-XXE309(L)-XX1/163/321/83/321/85/3243/16f501007012090140408065110100150120190DCEN (Straight)DCEN (Straight)DCEN (Straight)DCEP (Rever

34、se)DCEP (Reverse)DCEP (Reverse)DCEP (Reverse)FILLET WELDS and GROOVE WELDS on BACKING RINGSeFiller Metal CurrentLayer ClassificationaDia. (in) AmperesbPolarityRootcRootcRootcBalanceBalanceBalanceBalanceER309(L)ER309(L)ER309(L)E309(L)-XXdE309(L)-XXE309(L)-XXE309(L)-XX1/163/321/83/321/85/3243/16f50100

35、7012090140408065110100150120190DCEN (Straight)DCEN (Straight)DCEN (Straight)DCEP (Reverse)DCEP (Reverse)DCEP (Reverse)DCEP (Reverse)Permission to reproduce for intra-company use only is granted by the American Welding SocietyAWS B2.1-1/8-229:2002-AMD1 (2013)Page 5 of 17Standard Welding Procedure Spe

36、cification (SWPS)Metric Conversionsin mm F C ft3/h L/min NPS DN1/321/163/321/83/161/43/83/411-1/20.81.62.43.24.86.49.619.025.438.0503501017551015252.45.07.111.81/23/42025Permission to reproduce for intra-company use only is granted by the American Welding SocietyStandard Welding Procedure Specificat

37、ion (SWPS)Figure 1Allowable Joint DesignsAWS B2.1-1/8-229:2002-AMD1 (2013)Page 6 of 17Permission to reproduce for intra-company use only is granted by the American Welding SocietyFILLET WELDS: All Joints.GROOVE WELDS: For pipe and tubular products, see Joints 1 through 7. In addition, joints havingg

38、roove designs resulting from end preparations conforming with ASME B16.25, Butt Welding Ends,and prequalified joint details for complete joint penetration groove welded joints permitted by AWSD1.6, Structural Welding CodeStainless Steel, are also allowable for application with this SWPS.JOINT 1JOINT

39、 2Standard Welding Procedure Specification (SWPS)Figure 1 (Continued)Allowable Joint DesignsAWS B2.1-1/8-229:2002-AMD1 (2013)Page 7 of 17Permission to reproduce for intra-company use only is granted by the American Welding SocietyJOINT 3JOINT 4Standard Welding Procedure Specification (SWPS)Figure 1

40、(Continued)Allowable Joint DesignsAWS B2.1-1/8-229:2002-AMD1 (2013)Page 8 of 17JOINT 5JOINT 6Permission to reproduce for intra-company use only is granted by the American Welding SocietyStandard Welding Procedure Specification (SWPS)Figure 1 (Continued)Allowable Joint DesignsAWS B2.1-1/8-229:2002-AM

41、D1 (2013)Page 9 of 17TYPICAL BRANCH CONNECTIONJOINT 7RECOMMENDED WELDING DIMENSIONS FOR SOCKET WELDING COMPONENTS OTHER THAN FLANGESJOINT 8Permission to reproduce for intra-company use only is granted by the American Welding SocietyStandard Welding Procedure Specification (SWPS)Figure 1 (Continued)A

42、llowable Joint DesignsAWS B2.1-1/8-229:2002-AMD1 (2013)Page 10 of 17X MIN. = 1/4 Tn OR THE THICKNESS OF THE HUB, WHICHEVER IS SMALLER, UNLESS OTHERWISE REQUIRED BY THEFABRICATION DOCUMENT(S)Y MIN. = Tn OR 1/4 in, WHICHEVER IS SMALLER, UNLESS OTHERWISE REQUIRED BY THE FABRICATION DOCUMENT(S)Tn = NOMI

43、NAL PIPE WALL THICKNESSRECOMMENDED WELDING DIMENSIONS FOR FLANGESJOINT 9Figure 1 (Continued)Allowable Joint DesignsPermission to reproduce for intra-company use only is granted by the American Welding SocietyStandard Welding Procedure Specification (SWPS)AWS B2.1-1/8-229:2002-AMD1 (2013)Page 11 of 1

44、7Permission to reproduce for intra-company use only is granted by the American Welding SocietyAnnex A (Informative)Guidelines for the Preparation of Technical InquiriesThis annex is not part of AWS B2.1-1/8-229:2002-AMD1 (2013), Standard Welding Procedure Specification (SWPS)for Gas Tungsten Arc Wel

45、ding followed by Shielded Metal Arc Welding of Carbon Steel (M-1/P-1, Groups 1 or 2) toAustenitic Stainless Steel (M-8/P-8, Group 1), 1/8 through 1-1/2 inch Thick, ER309(L) and E309(L)-15, -16, or -17,As-Welded Condition, Primarily Pipe Applications, but is included for informational purposes only.A

46、1. IntroductionThe American Welding Society (AWS) Board of Direc-tors has adopted a policy whereby all official interpreta-tions of AWS standards are handled in a formal manner.Under this policy, all interpretations are made by thecommittee that is responsible for the standard. Officialcommunication

47、 concerning an interpretation is directedthrough the AWS staff member who works with thatcommittee. The policy requires that all requests for aninterpretation be submitted in writing. Such requests willbe handled as expeditiously as possible, but due to thecomplexity of the work and the procedures t

48、hat must befollowed, some interpretations may require considerabletime.A2. ProcedureAll inquiries shall be directed to:Managing DirectorTechnical Services DivisionAmerican Welding Society8669 Doral Blvd., Suite 130Doral, FL 33166All inquiries shall contain the name, address, and affilia-tion of the

49、inquirer, and they shall provide enough infor-mation for the committee to understand the point ofconcern in the inquiry. When the point is not clearlydefined, the inquiry will be returned for clarification. Forefficient handling, all inquiries should be typewritten andin the format specified below.A2.1 Scope. Each inquiry shall address one single provi-sion of th