ANSI AWS B2.1-8-009-2002 Standard Welding Procedure Specification (SWPS) for Gas Tungsten Arc Welding of Austenitic Stainless Steel (M-8 P-8 or S-8) 18 through 10 Gauge in the As-W.pdf

1、AWS B2.1-8-009:2002 (R2013)An American National StandardStandard Welding ProcedureSpecification (SWPS) forGasTungsten ArcWelding of AusteniticStainless Steel (M-8,P-8, or S-8), 18 through10 Gauge, in theAs-Welded Condition,with or without BackingSite LicenseAWS B2.1-8-009:2002 (R2013)An American Nat

2、ional StandardApproved by theAmerican National Standards InstituteJune 10, 2002Reaffirmed: March 11, 2013Standard Welding Procedure Specification (SWPS) forGas Tungsten Arc Welding of Austenitic StainlessSteel (M-8, P-8, or S-8), 18 through 10 Gauge,in the As-Welded Condition,with or without Backing

3、2nd EditionSupersedes ANSI/AWS B2.1.009-90Prepared by theAmerican Welding Society (AWS) B2 Committee on Procedure and Performance QualificationUnder the Direction of theAWS Technical Activities CommitteeApproved by theAWS Board of DirectorsAbstractThis standard contains the essential welding variabl

4、es for welding austenitic stainless steel in the thickness range of 18through 10 gauge using manual gas tungsten arc welding. It cites the base metals and operating conditions necessary tomake the weldment, the filler metal specifications, and the allowable joint designs for fillet welds and groove

5、welds.AWS B2.1-8-009:2002 (R2013)International Standard Book Number: 0-87171-681-XAmerican Welding Society8669 Doral Blvd., Suite 130, Doral, FL 33166 2002 by American Welding SocietyAll rights reservedPrinted in the United States of AmericaReaffirmed: March 11, 2013iiAWS B2.1-8-009:2002 (R2013)Stat

6、ement on the Use of American Welding Society StandardsAll standards (codes, specifications, recommended practices, methods, classifications, and guides) of the AmericanWelding Society (AWS) are voluntary consensus standards that have been developed in accordance with the rules of theAmerican Nationa

7、l Standards Institute (ANSI). When AWS American National Standards are either incorporated in, ormade part of, documents that are included in federal or state laws and regulations, or the regulations of other govern-mental bodies, their provisions carry the full legal authority of the statute. In su

8、ch cases, any changes in those AWSstandards must be approved by the governmental body having statutory jurisdiction before they can become a part ofthose laws and regulations. In all cases, these standards carry the full legal authority of the contract or other documentthat invokes the AWS standards

9、. Where this contractual relationship exists, changes in or deviations from requirementsof an AWS standard must be by agreement between the contracting parties.AWS American National Standards are developed through a consensus standards development process that bringstogether volunteers representing

10、varied viewpoints and interests to achieve consensus. While AWS administers theprocess and establishes rules to promote fairness in the development of consensus, it does not independently test, evalu-ate, or verify the accuracy of any information or the soundness of any judgments contained in its st

11、andards.AWS disclaims liability for any injury to persons or to property, or other damages of any nature whatsoever, whetherspecial, indirect, consequential, or compensatory, directly or indirectly resulting from the publication, use of, or relianceon this standard. AWS also makes no guarantee or wa

12、rranty as to the accuracy or completeness of any informationpublished herein.In issuing and making this standard available, AWS is neither undertaking to render professional or other services for oron behalf of any person or entity, nor is AWS undertaking to perform any duty owed by any person or en

13、tity to someoneelse. Anyone using these documents should rely on his or her own independent judgment or, as appropriate, seek theadvice of a competent professional in determining the exercise of reasonable care in any given circumstances. It isassumed that the use of this standard and its provisions

14、 is entrusted to appropriately qualified and competent personnel.This standard may be superseded by new editions. This standard may also be corrected through publication of amendmentsor errata or supplemented by publication of addenda. Information on the latest editions of AWS standards includingame

15、ndments, errata, and addenda is posted on the AWS web page (www.aws.org). Users should ensure that they have thelatest edition, amendments, errata, and addenda.Publication of this standard does not authorize infringement of any patent or trade name. Users of this standard acceptany and all liabiliti

16、es for infringement of any patent or trade name items. AWS disclaims liability for the infringement ofany patent or product trade name resulting from the use of this standard.AWS does not monitor, police, or enforce compliance with this standard, nor does it have the power to do so.Official interpre

17、tations of any of the technical requirements of this standard may only be obtained by sending a request,in writing, to the appropriate technical committee. Such requests should be addressed to the American Welding Society,Attention: Managing Director, Technical Services Division, 8669 Doral Blvd., S

18、uite 130, Doral, FL 33166 (see Annex A).With regard to technical inquiries made concerning AWS standards, oral opinions on AWS standards may be rendered.These opinions are offered solely as a convenience to users of this standard, and they do not constitute professionaladvice. Such opinions represen

19、t only the personal opinions of the particular individuals giving them. These individualsdo not speak on behalf of AWS, nor do these oral opinions constitute official or unofficial opinions or interpretations ofAWS. In addition, oral opinions are informal and should not be used as a substitute for a

20、n official interpretation.This standard is subject to revision at any time by the AWS B2 Committee on Procedure and Performance Qualification.It must be reviewed every five years, and if not revised, it must be either reaffirmed or withdrawn. Comments (recommen-dations, additions, or deletions) and

21、any pertinent data that may be of use in improving this standard are required andshould be addressed to AWS Headquarters. Such comments will receive careful consideration by the AWS B2 Committeeon Procedure and Performance Qualification and the author of the comments will be informed of the Committe

22、esresponse to the comments. Guests are invited to attend all meetings of the AWS B2 Committee on Procedure and Perfor-mance Qualification to express their comments verbally. Procedures for appeal of an adverse decision concerning all suchcomments are provided in the Rules of Operation of the Technic

23、al Activities Committee. A copy of these Rules can beobtained from the American Welding Society, 8669 Doral Blvd., Suite 130, Doral, FL 33166.iiiAWS B2.1-8-009:2002 (R2013)Personnel (Reaffirmation)AWS B2 Committee on Procedure and Performance QualificationJ. J. Fluckiger, Chair Idaho National Labora

24、toryJ. L. Cooley, 1st Vice Chair J. C. it is necessary to have at least a 6 volume changeof atmosphere within the purge zone prior to welding. It is not nec-essary to shield the root of fillet welds or groove welds with backingor back gouging.Flow Rate: A typical flow range of 5 to 15 ft3/h may be v

25、aried depending oncomponent configuration.Trailing Gas: NonePREHEAT AND INTERPASS TEMPERATUREPreheat Temperature: 50F minimum, 120F maximumInterpass Temperature: No maximumPreheat Maintenance: Continuous or special heating not requiredPOSTWELD HEAT TREATMENTPostweld Heat-Treatment: None (not qualifi

26、ed for PWHT)TUNGSTEN ELECTRODESSpecification: AWS A5.12, ASME SFA 5.12Classification: EWTh-2, EWLa-1.5Size: 1/8 in. max. sharpened to a pointELECTRICAL CHARACTERISTICSaAny 300 series filler metal conforming to A No. 8 may be selected to meet the strength requirements; however, corrosion requirements

27、 may dictate the specific selection.bAmperage shall not exceed the capacity of the Tungsten Electrodes.Pulsing Current: Not permittedBase MetalFiller Metal AmperesbCurrentClassificationaDia. (in.) Groove Fillet Type/Polarity18 ga.17 ga.16 ga.15 ga.14 ga.13 ga.12 ga.11 ga.10 ga.ER3XXER3XXER3XXER3XXER

28、3XXER3XXER3XXER3XXER3XX1/161/161/161/163/323/323/323/323/323560396443684772517655806085659070955055596468737782869195100105110115120125130DCEN (Straight)DCEN (Straight)DCEN (Straight)DCEN (Straight)DCEN (Straight)DCEN (Straight)DCEN (Straight)DCEN (Straight)DCEN (Straight)Permission to reproduce for

29、 intra-company use only is granted by the American Welding SocietyAWS B2.1-8-009:2002 (R2013)Page 4 of 13Standard Welding Procedure Specification (SWPS)TECHNIQUEBeads: Stringer or weavePeening: NoInitial Cleaning: Mechanical or chemical, joint shall be dry prior to weldingInterpass Cleaning: Mechani

30、cal onlySingle or Multiple Electrodes: SingleSingle or Multipass: EitherBackgouging: Not required, mechanical or thermal when used.Repair: Defects in welds shall be removed by mechanical or thermalmethods. The repair cavity may differ in contour and dimensionfrom a normal joint preparation and may p

31、resent different restraintconditions.COMPANY NAME _In the name of the Company stated above, I accept full responsibility for the application of this SWPS for usewith:_ Dated _Fabrication Document(s): (Such as Code, Specification, or Contract Document)Date _ Approved By _ Title _Permission to reprodu

32、ce for intra-company use only is granted by the American Welding SocietyStandard Welding Procedure Specification (SWPS)Figure 1Allowable Joint DesignsAWS B2.1-8-009:2002 (R2013)Page 5 of 13JOINT 1JOINT 2JOINT 3JOINT 4JOINT 5JOINT 6Permission to reproduce for intra-company use only is granted by the

33、American Welding SocietyStandard Welding Procedure Specification (SWPS)Figure 1 (Continued)Allowable Joint DesignsAWS B2.1-8-009:2002 (R2013)Page 6 of 13JOINT 7JOINT 8JOINT 9JOINT 10JOINT 11JOINT 12Metric Conversionsin. mm F C ft3/h L/min.0.05000.14061/163/321/81/45/81.2703.5711.6002.4003.2006.40015

34、.900050120350104917715257.111.8Permission to reproduce for intra-company use only is granted by the American Welding SocietyStandard Welding Procedure Specification (SWPS)AWS B2.1-8-009:2002 (R2013)Page 7 of 13A1. IntroductionThe American Welding Society (AWS) Board of Direc-tors has adopted a polic

35、y whereby all official interpreta-tions of AWS standards are handled in a formal manner.Under this policy, all interpretations are made by thecommittee that is responsible for the standard. Officialcommunication concerning an interpretation is directedthrough the AWS staff member who works with that

36、committee. The policy requires that all requests for aninterpretation be submitted in writing. Such requests willbe handled as expeditiously as possible, but due to thecomplexity of the work and the procedures that must befollowed, some interpretations may require considerabletime.A2. ProcedureAll i

37、nquiries shall be directed to:Managing DirectorTechnical Services DivisionAmerican Welding Society8669 Doral Blvd., Suite 130Doral, FL 33166All inquiries shall contain the name, address, and affilia-tion of the inquirer, and they shall provide enough infor-mation for the committee to understand the

38、point ofconcern in the inquiry. When the point is not clearlydefined, the inquiry will be returned for clarification. Forefficient handling, all inquiries should be typewritten andin the format specified below.A2.1 Scope. Each inquiry shall address one single provi-sion of the standard unless the po

39、int of the inquiryinvolves two or more interrelated provisions. The provi-sion(s) shall be identified in the scope of the inquiryalong with the edition of the standard that contains theprovision(s) the inquirer is addressing.A2.2 Purpose of the Inquiry. The purpose of theinquiry shall be stated in t

40、his portion of the inquiry. Thepurpose can be to obtain an interpretation of a standardsrequirement or to request the revision of a particularprovision in the standard.A2.3 Content of the Inquiry. The inquiry should beconcise, yet complete, to enable the committee to under-stand the point of the inq

41、uiry. Sketches should be usedwhenever appropriate, and all paragraphs, figures, andtables (or annex) that bear on the inquiry shall be cited. Ifthe point of the inquiry is to obtain a revision of the stan-dard, the inquiry shall provide technical justification forthat revision.A2.4 Proposed Reply. T

42、he inquirer should, as a pro-posed reply, state an interpretation of the provision thatis the point of the inquiry or provide the wording for aproposed revision, if this is what the inquirer seeks.A3. Interpretation of Provisions of the StandardInterpretations of provisions of the standard are made

43、bythe relevant AWS technical committee. The secretary ofthe committee refers all inquiries to the chair of theparticular subcommittee that has jurisdiction over theportion of the standard addressed by the inquiry. Thesubcommittee reviews the inquiry and the proposed replyto determine what the respon

44、se to the inquiry shouldbe. Following the subcommittees development of theAnnex AGuidelines for the Preparation of Technical InquiriesThis annex is not part of AWS B2.1-8-009:2002 (R2013), Standard Welding Procedure Specification (SWPS) forGas Tungsten Arc Welding of Austenitic Stainless Steel (M-8,

45、 P-8, or S-8), 18 through 10 Gauge, in theAs-Welded Condition, with or without Backing, but is included for informational purposes only.Permission to reproduce for intra-company use only is granted by the American Welding SocietyAWS B2.1-8-009:2002 (R2013)Page 8 of 13Standard Welding Procedure Speci

46、fication (SWPS)response, the inquiry and the response are presented tothe entire committee for review and approval. Uponapproval by the committee, the interpretation is an officialinterpretation of the Society, and the secretary transmitsthe response to the inquirer and to the Welding Journalfor pub

47、lication.A4. Publication of InterpretationsAll official interpretations will appear in the WeldingJournal and will be posted on the AWS web site.A5. Telephone InquiriesTelephone inquiries to AWS Headquarters concerningAWS standards should be limited to questions of a gen-eral nature or to matters di

48、rectly related to the use of thestandard. The AWS Board Policy Manual requires thatall AWS staff members respond to a telephone requestfor an official interpretation of any AWS standard withthe information that such an interpretation can beobtained only through a written request. Headquartersstaff c

49、annot provide consulting services. However, thestaff can refer a caller to any of those consultants whosenames are on file at AWS Headquarters.A6. AWS Technical CommitteesThe activities of AWS technical committees regarding in-terpretations are limited strictly to the interpretation ofprovisions of standards prepared by the committees or toconsideration of rev