ANSI AWS B2.1-8-013-2002 Standard Welding Procedure Specification (SWPS) for Shielded Metal Arc Welding of Austenitic Stainless Steel (M-8 P-8 S-8 Group 1) 10 through 18 Gauge in t.pdf

1、AWS B2.1-8-013:2002 (R2013)An American National StandardStandard Welding ProcedureSpecification (SWPS) forShielded Metal ArcWelding of AusteniticStainless Steel (M-8/P-8/S-8, Group 1),10 through 18 Gauge,in the As-WeldedCondition, with orwithout BackingSite LicenseAWS B2.1-8-013:2002 (R2013)An Ameri

2、can National StandardApproved by theAmerican National Standards InstituteJune 10, 2002Reaffirmed: March 11, 2013Standard Welding Procedure Specification (SWPS) forShielded Metal Arc Welding of Austenitic StainlessSteel (M-8/P-8/S-8, Group 1), 10 through18 Gauge, in the As-Welded Condition,with or wi

3、thout Backing2nd EditionSupersedes ANSI/AWS B2.1.013-91Prepared by theAmerican Welding Society (AWS) B2 Committee on Procedure and Performance QualificationUnder the Direction of theAWS Technical Activities CommitteeApproved by theAWS Board of DirectorsAbstractThis standard contains the essential we

4、lding variables for welding austenitic stainless steel in the thickness range of 18through 10 gauge using manual shielded metal arc welding. It cites the base metals and operating conditions necessary tomake the weldment, the filler metal specifications, and the allowable joint designs for fillet we

5、lds and groove welds.AWS B2.1-8-013:2002 (R2013)International Standard Book Number: 0-87171-685-2American Welding Society8669 Doral Blvd., Suite 130, Doral, FL 33166 2002 by American Welding SocietyAll rights reservedPrinted in the United States of AmericaErrata: 2nd Printing, December 2012Reaffirme

6、d: March 11, 2013iiAWS B2.1-8-013:2002 (R2013)Statement on the Use of American Welding Society StandardsAll standards (codes, specifications, recommended practices, methods, classifications, and guides) of the AmericanWelding Society (AWS) are voluntary consensus standards that have been developed i

7、n accordance with the rules of theAmerican National Standards Institute (ANSI). When AWS American National Standards are either incorporated in, ormade part of, documents that are included in federal or state laws and regulations, or the regulations of other govern-mental bodies, their provisions ca

8、rry the full legal authority of the statute. In such cases, any changes in those AWSstandards must be approved by the governmental body having statutory jurisdiction before they can become a part ofthose laws and regulations. In all cases, these standards carry the full legal authority of the contra

9、ct or other documentthat invokes the AWS standards. Where this contractual relationship exists, changes in or deviations from requirementsof an AWS standard must be by agreement between the contracting parties.AWS American National Standards are developed through a consensus standards development pr

10、ocess that bringstogether volunteers representing varied viewpoints and interests to achieve consensus. While AWS administers theprocess and establishes rules to promote fairness in the development of consensus, it does not independently test, evalu-ate, or verify the accuracy of any information or

11、the soundness of any judgments contained in its standards.AWS disclaims liability for any injury to persons or to property, or other damages of any nature whatsoever, whetherspecial, indirect, consequential, or compensatory, directly or indirectly resulting from the publication, use of, or relianceo

12、n this standard. AWS also makes no guarantee or warranty as to the accuracy or completeness of any informationpublished herein.In issuing and making this standard available, AWS is neither undertaking to render professional or other services for oron behalf of any person or entity, nor is AWS undert

13、aking to perform any duty owed by any person or entity to someoneelse. Anyone using these documents should rely on his or her own independent judgment or, as appropriate, seek theadvice of a competent professional in determining the exercise of reasonable care in any given circumstances. It isassume

14、d that the use of this standard and its provisions is entrusted to appropriately qualified and competent personnel.This standard may be superseded by new editions. This standard may also be corrected through publication of amendmentsor errata or supplemented by publication of addenda. Information on

15、 the latest editions of AWS standards includingamendments, errata, and addenda is posted on the AWS web page (www.aws.org). Users should ensure that they have thelatest edition, amendments, errata, and addenda.Publication of this standard does not authorize infringement of any patent or trade name.

16、Users of this standard acceptany and all liabilities for infringement of any patent or trade name items. AWS disclaims liability for the infringement ofany patent or product trade name resulting from the use of this standard.AWS does not monitor, police, or enforce compliance with this standard, nor

17、 does it have the power to do so.Official interpretations of any of the technical requirements of this standard may only be obtained by sending a request,in writing, to the appropriate technical committee. Such requests should be addressed to the American Welding Society,Attention: Managing Director

18、, Technical Services Division, 8669 Doral Blvd., Suite 130, Doral, FL 33166 (see Annex A).With regard to technical inquiries made concerning AWS standards, oral opinions on AWS standards may be rendered.These opinions are offered solely as a convenience to users of this standard, and they do not con

19、stitute professionaladvice. Such opinions represent only the personal opinions of the particular individuals giving them. These individualsdo not speak on behalf of AWS, nor do these oral opinions constitute official or unofficial opinions or interpretations ofAWS. In addition, oral opinions are inf

20、ormal and should not be used as a substitute for an official interpretation.This standard is subject to revision at any time by the AWS B2 Committee on Procedure and Performance Qualification.It must be reviewed every five years, and if not revised, it must be either reaffirmed or withdrawn. Comment

21、s (recommen-dations, additions, or deletions) and any pertinent data that may be of use in improving this standard are required andshould be addressed to AWS Headquarters. Such comments will receive careful consideration by the AWS B2 Committeeon Procedure and Performance Qualification and the autho

22、r of the comments will be informed of the Committeesresponse to the comments. Guests are invited to attend all meetings of the AWS B2 Committee on Procedure and Perfor-mance Qualification to express their comments verbally. Procedures for appeal of an adverse decision concerning all suchcomments are

23、 provided in the Rules of Operation of the Technical Activities Committee. A copy of these Rules can beobtained from the American Welding Society, 8669 Doral Blvd., Suite 130, Doral, FL 33166.iiiAWS B2.1-8-013:2002 (R2013)Personnel (Reaffirmation)AWS B2 Committee on Procedure and Performance Qualifi

24、cationJ. J. Fluckiger, Chair Idaho National LaboratoryJ. L. Cooley, 1st Vice Chair J. C. how-ever, corrosion requirements may dictate the specific selection.Pulsing Current: Not permittedTECHNIQUEBeads: Stringer or weavePeening: NoInitial Cleaning: Mechanical or chemical, joint shall be dry prior to

25、 weldingInterpass Cleaning: Mechanical onlySingle or Multiple Electrodes: SingleSingle or Multipass: EitherBackgouging: Not required, mechanical or thermal if usedRepair: Defects in welds shall be removed by mechanical or thermalmethods. The repair cavity may differ in contour and dimensionfrom a no

26、rmal joint preparation and may present different restraintconditions.COMPANY NAME _In the name of the Company stated above, I accept full responsibility for the application of this SWPS for usewith:_ Dated _Fabrication Document(s): (Such as Code, Specification, or Contract Document)Date _ Approved B

27、y _ Title _Base MetalFiller Metal Amperes CurrentClassificationaDia. (in.) Groove Fillet Type/Polarity18 ga.17 ga.16 ga.15 ga.14 ga.13 ga.12 ga.11 ga.10 ga.E3XX-15, 16, or 17E3XX-15, 16, or 17E3XX-15, 16, or 17E3XX-15, 16, or 17E3XX-15, 16, or 17E3XX-15, 16, or 17E3XX-15, 16, or 17E3XX-15, 16, or 17

28、E3XX-15, 16, or 173/32 max.3/32 max.3/32 max.3/32 max.3/32 max.3/32 max.3/32 max.3/32 max.1/8 max.556057675969617163736575677769797080556057675974618163886595671026910970115All Gauges:DCEP (E3XX-15)DCEN or DCEP(E3XX-16 or 17)Permission to reproduce for intra-company use only is granted by the Americ

29、an Welding SocietyStandard Welding Procedure Specification (SWPS)Figure 1Allowable Joint DesignsAWS B2.1-8-013:2002 (R2013)Page 4 of 13GAGE: 14, 15, 16, 17, AND 18JOINT 1GAGE: 10, 11, 12, AND 13JOINT 2GAGE: 14, 15, 16, 17, AND 18JOINT 3GAGE: 10, 11, 12, AND 13JOINT 4JOINT 5JOINT 6Permission to repro

30、duce for intra-company use only is granted by the American Welding SocietyStandard Welding Procedure Specification (SWPS)Figure 1 (Continued)Allowable Joint DesignsAWS B2.1-8-013:2002 (R2013)Page 5 of 13JOINT 7JOINT 8JOINT 9JOINT 10JOINT 11JOINT 12JOINT 13Permission to reproduce for intra-company us

31、e only is granted by the American Welding SocietyStandard Welding Procedure Specification (SWPS)Figure 1 (Continued)Allowable Joint DesignsAWS B2.1-8-013:2002 (R2013)Page 6 of 13JOINT 14Metric Conversionsin. mm F C0.05000.14063/321/81.2703.5712.4003.200501201049175Figure 1 (Continued)Allowable Joint

32、 DesignsPermission to reproduce for intra-company use only is granted by the American Welding SocietyStandard Welding Procedure Specification (SWPS)AWS B2.1-8-013:2002 (R2013)Page 7 of 13A1. IntroductionThe American Welding Society (AWS) Board of Direc-tors has adopted a policy whereby all official

33、interpreta-tions of AWS standards are handled in a formal manner.Under this policy, all interpretations are made by thecommittee that is responsible for the standard. Officialcommunication concerning an interpretation is directedthrough the AWS staff member who works with thatcommittee. The policy r

34、equires that all requests for aninterpretation be submitted in writing. Such requests willbe handled as expeditiously as possible, but due to thecomplexity of the work and the procedures that must befollowed, some interpretations may require considerabletime.A2. ProcedureAll inquiries shall be direc

35、ted to:Managing DirectorTechnical Services DivisionAmerican Welding Society8669 Doral Blvd., Suite 130Doral, FL 33166All inquiries shall contain the name, address, and affilia-tion of the inquirer, and they shall provide enough infor-mation for the committee to understand the point ofconcern in the

36、inquiry. When the point is not clearlydefined, the inquiry will be returned for clarification. Forefficient handling, all inquiries should be typewritten andin the format specified below.A2.1 Scope. Each inquiry shall address one single provi-sion of the standard unless the point of the inquiryinvol

37、ves two or more interrelated provisions. The provi-sion(s) shall be identified in the scope of the inquiryalong with the edition of the standard that contains theprovision(s) the inquirer is addressing.A2.2 Purpose of the Inquiry. The purpose of theinquiry shall be stated in this portion of the inqu

38、iry. Thepurpose can be to obtain an interpretation of a standardsrequirement or to request the revision of a particularprovision in the standard.A2.3 Content of the Inquiry. The inquiry should beconcise, yet complete, to enable the committee to under-stand the point of the inquiry. Sketches should b

39、e usedwhenever appropriate, and all paragraphs, figures, andtables (or annex) that bear on the inquiry shall be cited. Ifthe point of the inquiry is to obtain a revision of the stan-dard, the inquiry shall provide technical justification forthat revision.A2.4 Proposed Reply. The inquirer should, as

40、a pro-posed reply, state an interpretation of the provision thatis the point of the inquiry or provide the wording for aproposed revision, if this is what the inquirer seeks.A3. Interpretation of Provisions of the StandardInterpretations of provisions of the standard are made bythe relevant AWS tech

41、nical committee. The secretary ofthe committee refers all inquiries to the chair of theparticular subcommittee that has jurisdiction over theportion of the standard addressed by the inquiry. Thesubcommittee reviews the inquiry and the proposed replyto determine what the response to the inquiry shoul

42、dbe. Following the subcommittees development of theAnnex AGuidelines for the Preparation of Technical InquiriesThis annex is not part of AWS B2.1-8-013:2002 (R2013), Standard Welding Procedure Specification (SWPS) forShielded Metal Arc Welding of Austenitic Stainless Steel (M-8/P-8/S-8, Group 1), 10

43、 through 18 Gauge, in theAs-Welded Condition, with or without Backing, but is included for informational purposes only.Permission to reproduce for intra-company use only is granted by the American Welding SocietyAWS B2.1-8-013:2002 (R2013)Page 8 of 13Standard Welding Procedure Specification (SWPS)re

44、sponse, the inquiry and the response are presented tothe entire committee for review and approval. Uponapproval by the committee, the interpretation is an officialinterpretation of the Society, and the secretary transmitsthe response to the inquirer and to the Welding Journalfor publication.A4. Publ

45、ication of InterpretationsAll official interpretations will appear in the WeldingJournal and will be posted on the AWS web site.A5. Telephone InquiriesTelephone inquiries to AWS Headquarters concerningAWS standards should be limited to questions of a gen-eral nature or to matters directly related to

46、 the use of thestandard. The AWS Board Policy Manual requires thatall AWS staff members respond to a telephone requestfor an official interpretation of any AWS standard withthe information that such an interpretation can beobtained only through a written request. Headquartersstaff cannot provide con

47、sulting services. However, thestaff can refer a caller to any of those consultants whosenames are on file at AWS Headquarters.A6. AWS Technical CommitteesThe activities of AWS technical committees regarding in-terpretations are limited strictly to the interpretation ofprovisions of standards prepare

48、d by the committees or toconsideration of revisions to existing provisions on thebasis of new data or technology. Neither AWS staff northe committees are in a position to offer interpretive orconsulting services on (1) specific engineering problems,(2) requirements of standards applied to fabricatio

49、ns out-side the scope of the document, or (3) points not specifi-cally covered by the standard. In such cases, the inquirershould seek assistance from a competent engineer expe-rienced in the particular field of interest.Permission to reproduce for intra-company use only is granted by the American Welding SocietyAWS B2.1-8-013:2002 (R2013)Page 9 of 13List of