ANSI AWWA C111 A21.11-2017 Rubber-Gasket Joints for Ductile-Iron Pressure Pipe and Fittings.pdf

1、AWWA Standard SM Rubber-Gasket Joints for Ductile-Iron Pressure Pipe and Fittings Effective date: April 1, 2017. First edition approved by AWWA Board of Directors July 16, 1953. This edition approved Jan. 14, 2017. Approved by American National Standards Institute Oct. 11, 2016. ANSI/AWWA C111/A21.1

2、1-17 (Revision of ANSI/AWWA C111/A21.11-12) Copyright 2017 American Water Works Association. All Rights Reserved. ii AWWA Standard This document is an American Water Works Association (AWWA) standard. It is not a specification. AWWA standards describe minimum requirements and do not contain all of t

3、he engineering and administrative information normally contained in specifications. The AWWA standards usually contain options that must be evaluated by the user of the standard. Until each optional feature is specified by the user, the product or service is not fully defined. AWWA pub- lication of

4、a standard does not constitute endorsement of any product or product type, nor does AWWA test, certify, or approve any product. The use of AWWA standards is entirely voluntary. This standard does not supersede or take precedence over or displace any applicable law, regulation, or code of any governm

5、ental authority. AWWA standards are intended to represent a consensus of the water industry that the product described will provide satisfactory ser- vice. When AWWA revises or withdraws this standard, an official notice of action will be placed on the first page of the Official Notice section of Jo

6、urnal American Water Works Association. The action becomes effective on the first day of the month following the month of Journal American Water Works Association publication of the official notice. American National Standard An American National Standard implies a consensus of those substantially c

7、oncerned with its scope and provisions. An American National Standard is intended as a guide to aid the manufacturer, the consumer, and the general public. The existence of an American National Standard does not in any respect preclude anyone, whether that person has approved the standard or not, fr

8、om manufacturing, marketing, purchasing, or using products, processes, or proce - dures not conforming to the standard. American National Standards are subject to periodic review, and users are cau- tioned to obtain the latest editions. Producers of goods made in conformity with an American National

9、 Standard are encouraged to state on their own responsibility in advertising and promotional materials or on tags or labels that the goods are produced in conformity with particular American National Standards. Caution n oti Ce : The American National Standards Institute (ANSI) approval date on the

10、front cover of this standard indicates completion of the ANSI approval process. This American National Standard may be revised or withdrawn at any time. ANSI procedures require that action be taken to reaffirm, revise, or withdraw this standard no later than five years from the date of publication.

11、Purchasers of American National Standards may receive current information on all standards by calling or writing the American National Standards Institute, 25 West 43rd Street, Fourth Floor, New York, NY 10036; 212.642.4900; or emailing infoansi.org. hours of work by your fellow water professionals.

12、 Revenue from the sales of this AWWA material supports ongoing product development. Unauthorized distribution, either electronic or photocopied, is illegal and hinders AWWAs mission to support the water community. This AWWA content is the product of thousands of ISBN-13, print: 978-1-58321-210-8 eIS

13、BN-13, electronic: 978-1-61300-409-8 DOI: http:/dx.doi.org/10.12999/AW WA.C111.17 All rights reserved. No part of this publication may be reproduced or transmitted in any form or by any means, electronic or mechanical, including photocopy, recording, or any information or retrieval system, except in

14、 the form of brief excerpts or quotations for review purposes, without the written permission of the publisher. Copyright 2017 by American Water Works Association Printed in USA Copyright 2017 American Water Works Association. All Rights Reserved. iii Committee Personnel Subcommittee 2, Joints for P

15、ipe and Fittings, which reviewed and developed this standard, had the following personnel at the time: Larry Dunn, Chair General Interest Members S.M. Passarelli,* Standards Engineer Liaison, AWWA, Denver, Colo. (AWWA) P.A. Selig, Consultant, Birmingham, Ala. (AWWA) Producer Members L.R. Dunn, U.S.

16、Pipe (2) inclusion of reduced ductile-iron mechanical-joint pipe bell thicknesses that are compatible with pipe barrel thicknesses; (3) inclusion of tee-head bolts with reduced shank diameters that are properly sized to accept rolled threads; (4) minimum elonga- tion increased to 5 percent for ducti

17、le-iron glands; (5) deletion of the 2-in. and 2-in. sizes; and (6) marking requirements for the tee-head bolts and nuts. A 1984 addendum was issued to increase the thread length on 5/8-in. 3-in. and -in. 3-in. tee-head bolts by in. and to permit polygon-shaped bells on fittings. The major revisions

18、in the 1985 edition included the addition of Sec. 11-1.3, Modi - fications to Push-on and Mechanical Joints; revision of Sec. 11-2.5 defining the manu- facturer as the party that produces joints according to this standard; and the addition Copyright 2017 American Water Works Association. All Rights Reserved.