ANSI AWWA C217-2016 Microcrystalline Wax and Petrolatum Tape Coating Systems for Steel Water Pipe and Fittings (Incorporates Addendum dated April 2017).pdf

1、AWWA Standard SM Microcrystalline Wax and Petrolatum Tape Coating Systems for Steel Water Pipe and Fittings Effective date: Aug. 1, 2016. First edition approved by AWWA Board of Directors June 21, 1990. This edition approved Jan. 16, 2016. Approved by American National Standards Institute Jan. 8, 20

2、16. ANSI/AWWA C217-16 (Revision of ANSI/AWWA C217-09)ii AWWA Standard This document is an American Water Works Association (AWWA) standard. It is not a specification. AWWA standards describe minimum requirements and do not contain all of the engineering and administrative information normally contai

3、ned in specifications. The AWWA standards usually contain options that must be evaluated by the user of the standard. Until each optional feature is specified by the user, the product or service is not fully defined. AWWA pub- lication of a standard does not constitute endorsement of any product or

4、product type, nor does AWWA test, certify, or approve any product. The use of AWWA standards is entirely voluntary. This standard does not supersede or take precedence over or displace any applicable law, regulation, or code of any governmental authority. AWWA standards are intended to represent a c

5、onsensus of the water industry that the product described will provide satisfactory ser- vice. When AWWA revises or withdraws this standard, an official notice of action will be placed on the first page of the Official Notice section of Journal American Water Works Association. The action becomes ef

6、fective on the first day of the month following the month of Journal American Water Works Association publication of the official notice. American National Standard An American National Standard implies a consensus of those substantially concerned with its scope and provisions. An American National

7、Standard is intended as a guide to aid the manufacturer, the consumer, and the general public. The existence of an American National Standard does not in any respect preclude anyone, whether that person has ap - proved the standard or not, from manufacturing, marketing, purchasing, or using products

8、, processes, or procedures not conforming to the standard. American National Standards are subject to periodic review, and users are cautioned to obtain the latest editions. Producers of goods made in conformity with an American National Standard are encour - aged to state on their own responsibilit

9、y in advertising and promotional materials or on tags or labels that the goods are produced in conformity with particular American National Standards. Caution n oti Ce : The American National Standards Institute (ANSI) approval date on the front cover of this standard indicates completion of the ANS

10、I approval process. This American National Standard may be revised or withdrawn at any time. ANSI procedures require that action be taken to reaffirm, revise, or withdraw this standard no later than five years from the date of publication. Purchasers of American National Standards may receive curren

11、t information on all standards by calling or writing the American National Standards Institute, 25 West 43rd Street, Fourth Floor, New York, NY 10036; 212.642.4900; or emailing infoansi.org. ISBN-13, print: 978-1-62576-174-3 eISBN-13, electronic: 978-1-61300-385-5DOI: http:/dx.doi.org/10.12999/AWWA.

12、C217.16 All rights reserved. No part of this publication may be reproduced or transmitted in any form or by any means, electronic or mechanical, including photocopy, recording, or any information or retrieval system, except in the form of brief excerpts or quotations for review purposes, without the

13、 written permission of the publisher. Copyright 2016 by American Water Works Association Printed in USA hours of work by your fellow water professionals. Revenue from the sales of this AWWA material supports ongoing product development. Unauthorized distribution, either electronic or photocopied, is

14、 illegal and hinders AWWAs mission to support the water community. This AWWA content is the product of thousands ofiii Committee Personnel The Steel Water Pipe-Manufacturers Technical Advisory Committee (SWPMTAC) Task Group on updating ANSI/AWWA C217 had the following personnel at the time: Frank C.

15、 Rampton, Chair John A. Wise, Vice-Chair General Interest Members D. DAmbrosio, Polyguard Products, Ennis, Texas (AWWA) D. Libby, Chase Corporation, Westwood, Mass. (AWWA) R. Norsworthy, Polyguard Products, Ennis, Texas (AWWA) F.C. Rampton, Trenton Corporation, Ann Arbor, Mich. (AWWA) J.A. Wise, Can

16、us International Sales Inc., Surrey, B.C., Canada (AWWA) The AWWA Standards Committee on Steel Pipe, which reviewed and approved this standard, had the following personnel at the time of approval: John H. Bambei Jr., Chair Dennis Dechant, Vice-Chair John L. Luka, Secretary General Interest Members W

17、.R. Brunzell, Brunzell Associates Ltd., Skokie, Ill. (AWWA) R.J. Card, Lockwood, Andrews Jan. 24, 1999; Jan. 18, 2004; and Jan. 25, 2009. This edition was approved on Jan. 16, 2016. II. Special Issues. II.A. Advisory Information on Product Application. This standard defines the performance of cold-a

18、pplied petrolatum tape and petroleum wax tape coatings establishing the quality desired for long-term protection and prevention of corrosion. It applies to the exterior coating of steel water pipelines for underground and underwater installation under normal conditions. It is based on previous exper

19、ience but is not designed for unqualified use under all conditions. The advisability of its use for any installation must be reviewed by the purchaser. If an extended period of aboveground storage of coated pipe is anticipated, the materials ability to resist degradation by ultra- violet light and o

20、ther atmospheric and environmental conditions should be considered. III. Use of This Standard. It is the responsibility of the user of an AWWA standard to determine that the products described in that standard are suitable for use in the particular application being considered. III.A. Purchaser Opti

21、ons and Alternatives. The following items should be provided by the purchaser. 1. Standard used that is, ANSI/AWWA C217, Microcrystalline Wax and Petrolatum Tape Coating Systems for Steel Water Pipe and Fittings, of latest revision. 2. Any exceptions to the standard that may be required. * American

22、National Standards Institute, 25 West 43rd Street, Fourth Floor, New York, NY 10036.viii 3. Expected aboveground exposure time (foreword, Section II.A). 4. Description and dimensions of each type of special section for each type of exterior protection. a. Normal or average conditions. b. Unusual con

23、ditions (Sec. 1.1.1). 5. Physical properties of primer and coating (Table 1). 6. Coating-system thickness (Sec. 4.3.3.4). 7. Surface preparation (Sec. 4.4.1). 8. Tape coating repair (Sec. 4.4.4). 9. Inspection (Sec. 5.4). 10. Testing (Sec. 5.2). 11. Packaging and shipping (Sec. 6.2). 12. Affidavit o

24、f compliance, if required (Sec. 6.3). III.B. Modification to Standard. Any modification to the provisions, definitions, or terminology in this standard must be provided by the purchaser. I V. Major Revisions. Major revisions made to the standard in this edition include the following: 1. The title an

25、d scope of the standard were changed to add an additional wax type and expand the intended usage to include steel fittings. 2. The definition for petrolatum was revised and a new definition for micro- crystalline wax was added in place of petroleum wax (Section 3). 3. Section 4 was modified to be co

26、nsistent with the formatting and section numbers of other AWWA coating standards. 4. Table 1 was modified and new Tables 2, 3, and 4 were added to include information and requirements consistent with changes made to other AWWA coating standards. 5. The minimum breaking strength in Table 3 was modifi

27、ed to more accu- rately reflect the industry-accepted minimum. 6. Minimum thickness of primer listed in Table 4 was modified to require complete coverage to more accurately reflect industry practice. 7. Sec. 4.3 was modified to include the option of using a wax-based filler mate- rial in the coating

28、 system. 8. Portions of Sec. 4.5, Field Procedures, language were deleted and the reader is referred to AWWA C604 to be consistent with changes in other AWWA coating standards.ix 9. Section 5, Verification, was modified to be consistent with the new language and format being used in other AWWA coati

29、ng standards. 10. New requirements and sections for dielectric strength (Sec. 5.2.2.4), cathodic disbondment testing (Table 3 and Sec. 5.2.2.5), breaking strength (Sec. 5.2.2.6), and elongation (Sec. 5.2.2.7) were added for consistency with other AWWA coating standards. 11. A new Sec. 5.3, Quality A

30、ssurance and Records, was added. 12. A new Sec. 5.4, Inspection and Testing by the Purchaser, was added. 13. Under new Sec. 5.5, Quality Control Requirements of Applied Coating System, new requirements for coating appearance (Sec. 5.5.1) and primer thickness (Sec. 5.5.2) were added. 14. The El ectri

31、cal Continuity Inspection section was updated (Sec. 5.5.3). 15. Previous Sec. 5.3, Notice of Nonconformance, was renamed Rejection (new Sec. 5.6) and revised. 16. Section 6, Delivery, was modified to be consistent with other AWWA coat- ing standards. 17. A new Sec. 6.2.1.4 was added under Packaging

32、and Shipping to include wax-based filler. 18. The information in Sec. 6.2.2, Shipping, Handling, and Storage, was updated. 19. Sec. 6.3, Affidavit of Compliance, was modified to include an affidavit for workmanship. V. Comments. If you have any comments or questions about this standard, please call

33、AWWA Engineering and Technical Services at 303.794.7711, FAX at 303.795.7603; write to the department at 6666 West Quincy Avenue, Denver, CO 80235-3098; or email at standardsawwa.org.This page intentionally blank.1 AWWA Standard ANSI/AWWA C217-16 (Revision of ANSI/AWWA C217-09) Microcrystalline Wax

34、and Petrolatum Tape Coating Systems for Steel Water Pipe and Fittings SECTION 1: GENERAL Sec. 1.1 Scope This standard establishes minimum requirements for microcrystalline wax and petrolatum tape coating systems for steel water pipe and fittings. This standard describes exterior coatings that consis

35、t of cold-applied micro- crystalline wax or petrolatum primers and tapes and their applications to special sections, connections, and fittings to be used with buried, submerged, and above- ground steel water pipelines. The primers and tapes are not intended for use with steel joints or sections of s

36、teel pipe where coatings of cement mortar or concrete are applied directly onto the bare steel pipe. These coatings may be field- or shop- applied according to the provisions of this standard. 1.1.1 Conditions not described in this standard. This standard does not describe the additional materials a

37、nd procedures that may be required for difficult conditions, such as those encountered in building some submarine lines, casing pipe, river crossings, and lines that are in rocky areas or in severe soil stress. Consult the manufacturer for the additional materials and procedures that may be required for these conditions. These materials may not be described in this standard.