ANSI AWWA C542-2016 Electric Motor Actuators for Valves and Slide Gates.pdf

1、AWWA Standard SM Electric Motor Actuators for Valves and Slide Gates Effective date: Sept. 1, 2016. First edition approved by AWWA Board of Directors Jan. 25, 2009. This edition approved Jan. 16, 2016. Approved by American National Standards Institute Apr. 7, 2016. ANSI/AWWA C542-16 (Revision of ANS

2、I/AWWA C542-09) Copyright 2016 American Water Works Association. All Rights Reserved.ii AWWA Standard This document is an American Water Works Association (AWWA) standard. It is not a specification. AWWA standards describe minimum requirements and do not contain all of the engineering and administra

3、tive information normally contained in specifications. The AWWA standards usually contain options that must be evaluated by the user of the standard. Until each optional feature is specified by the user, the product or service is not fully defined. AWWA pub- lication of a standard does not constitut

4、e endorsement of any product or product type, nor does AWWA test, certify, or approve any product. The use of AWWA standards is entirely voluntary. This standard does not supersede or take precedence over or displace any applicable law, regulation, or code of any governmental authority. AWWA standar

5、ds are intended to represent a consensus of the water industry that the product described will provide satisfactory ser- vice. When AWWA revises or withdraws this standard, an official notice of action will be placed on the first page of the Official Notice section of Journal American Water Works As

6、sociation. The action becomes effective on the first day of the month following the month of Journal American Water Works Association publication of the official notice. American National Standard An American National Standard implies a consensus of those substantially concerned with its scope and p

7、rovisions. An American National Standard is intended as a guide to aid the manufacturer, the consumer, and the general public. The existence of an American National Standard does not in any respect preclude anyone, whether that person has ap - proved the standard or not, from manufacturing, marketin

8、g, purchasing, or using products, processes, or procedures not conforming to the standard. American National Standards are subject to periodic review, and users are cautioned to obtain the latest editions. Producers of goods made in conformity with an American National Standard are encour - aged to

9、state on their own responsibility in advertising and promotional materials or on tags or labels that the goods are produced in conformity with particular American National Standards. Caution n oti Ce : The American National Standards Institute (ANSI) approval date on the front cover of this standard

10、 indicates completion of the ANSI approval process. This American National Standard may be revised or withdrawn at any time. ANSI procedures require that action be taken to reaffirm, revise, or withdraw this standard no later than five years from the date of publication. Purchasers of American Natio

11、nal Standards may receive current information on all standards by calling or writing the American National Standards Institute, 25 West 43rd Street, Fourth Floor, New York, NY 10036; 212.642.4900; or emailing infoansi.org. ISBN-13, print: 978-1-62576-177-4 eISBN-13, electronic: 978-1-61300-388-6 DOI

12、: http:/dx.doi.org/10.12999/AWWA.C542.16 All rights reserved. No part of this publication may be reproduced or transmitted in any form or by any means, electronic or mechanical, including photocopy, recording, or any information or retrieval system, except in the form of brief excerpts or quotations

13、 for review purposes, without the written permission of the publisher. Copyright 2016 by American Water Works Association Printed in USA hours of work by your fellow water professionals. Revenue from the sales of this AWWA material supports ongoing product development. Unauthorized distribution, eit

14、her electronic or photocopied, is illegal and hinders AWWAs mission to support the water community. This AWWA content is the product of thousands of Copyright 2016 American Water Works Association. All Rights Reserved.iii Committee Personnel The AWWA Standards Subcommittee on Electric Actuators, whi

15、ch reviewed and approved this standard, had the following personnel at the time of approval: Dave Montgomery, Chair General Interest Members A. Ali, ADA Consulting Ltd., Surry, B.C., Canada (AWWA) K.H. Hipps, CDM Smith, Chicago, Ill. (AWWA) W.H. Peffley, Crawford Murphy ANSI/AWWA C504, Rubber-Seated

16、 Butterfly Valves; ANSI/AWWA C507, Ball Valves, 6 In. Through 60 In. (150 mm Through 1,500 mm); ANSI/AWWA C509, Resilient-Seated Gate Valves for Water Supply Service; ANSI/AWWA C516 Large-Diameter Rubber-Seated Butterfly Valves, Sizes 78 In. (2,000 mm) and Larger; ANSI/AWWA C517, Resilient-Seated Ca

17、st-Iron Eccentric Plug Valves; ANSI/A WWA C560, Cast-Iron Slide Gates; ANSI/A WWA C561, * American National Standards Institute, 25 West 43rd Street, Fourth Floor, New York, NY 10036. Copyright 2016 American Water Works Association. All Rights Reserved.viii Fabricated Stainless-Steel Slide Gates; AN

18、SI/AWWA C562, Fabricated Aluminum Slide Gates; and ANSI/ AWWA C563, Fabricated Composite Slide Gates. ANSI/AWWA C542 describes only the design and performance of those actuat- ing devices applied to systems with operating pressures normally encountered in water utilities. Purchasers of electric moto

19、r actuators should carefully review the require- ments of this standard, evaluate the information to be provided to the manufacturer, and review the data to be supplied by the manufacturer. Such evaluations are essential to allow proper application of the electric motor actuator for the intended use

20、. ANSI/AWWA C542 references the National Electrical Manufacturers Association (NEMA),* which publishes standards and application guides for electrical equipment, enclosures, and components for various hazardous and nonhazardous service. Users of ANSI/AWWA C542 are cautioned to clearly specify the ap

21、plication requirements for the service. Such service may include depth and duration for submerged application, explosion-proof, and outdoor application. Specific requirements for controls and accessories and other items not covered by this standard shall be included in the purchase documents. Users

22、of this standard should consult the National Electrical Code and local codes for circuit breakers/disconnect switch requirements. III. Use of This Standard. It is the responsibility of the user of an AWWA standard to determine that the products described in that standard are suitable for use in the

23、particular application being considered. There are numerous lists throughout this standard describing various features of electric motor actuators. These lists are intended to be nonlimiting in nature and may not include all features necessary for a particular application or that a particular purcha

24、ser may desire. This standard includes certain options that shall be selected and specified by the purchaser to completely describe and obtain the actuator desired. In addition to the factors in Sec. III.A, Purchaser Options and Alternatives, other factors to be considered when sizing an actuator ar

25、e described in Sec. 4.3, Actuator Sizing. The following sum- marizes the options that shall be selected and the data that shall be covered in the pur- chase documents covering actuators manufactured in accordance with this standard. III.A. Purchaser Options and Alternatives. The following informatio

26、n should be provided or requested by the purchaser: * National Electrical Manufacturers Association, 1300 North 17th Street, Suite 1752, Rosslyn, VA 22209. Copyright 2016 American Water Works Association. All Rights Reserved.ix 1. Standard usedthat is ANSI/AWWA C542, Electric Motor Actuators for Val

27、ves and Slide Gates, of latest revision. 2. The purchaser should note that corrosion-resistant metals shall be carefully selected and required to be compatible with the environmental conditions to which they are exposed in a given application (Section 3, item 3). 3. Details of federal, state or prov

28、incial, and local requirements (Sec. 4.1). 4. Modifications to manufacturer delivery requirements (Sec. 4.2). 5. Valve and slide gate physical characteristics (Sec. 4.3). a. Size and type of valve or slide gate to be operated by the actuator. b. Stem or shaft diameter at point of attachment. c. Risi

29、ng stem, nonrising stem, or quarter turn. d. Pitch, lead, hand of thread, or keyway dimensions. e. Weight of gate and stem for slide gate. f. Actuator orientation in relation to valve or slide gate. g. Actuator mounting: directly mounted or remotely mounted on a floor stand and coupled with extensio

30、n shafting. h. Seating/unseating torque in foot-pounds (newton-meters), maximum dynamic torque in foot-pounds (newton-meters), and when applicable, thrust in pounds (newtons) (Sec. 4.3.1.2). i. Maximum torque/thrust capability of the valve or slide gate (Sec. 4.3.2). 6. Lost-motion device requiremen

31、t (Sec. 4.4.3). 7. Lubricant requirements (Sec. 4.4.5). 8. Direction of rotation of actuator handwheel to open valve or slide gate if other than counterclockwise (Sec. 4.4.6). 9. Supply voltage with maximum and minimum variation, phase, and fre- quency (Sec. 4.4.7). 10. Required type of service (Sec

32、. 4.4.7). a. Openclose. Frequency of operation and travel time duty cycle. b. Throttling/modulating. Operating conditions, input signal to actuator, and starts per hour. Class 160 starts per hour, maximum. Class 2100 starts per hour, maximum. Class 3600 starts per hour, maximum. Class 41,200 starts per hour, maximum. 11. Ambient temperature and humidity ranges. Copyright 2016 American Water Works Association. All Rights Reserved.