ANSI AWWA C602-2017 Cement CMortar Lining of Water Pipelines in Place-4 In (100 mm) and Larger.pdf

1、AWWA Standard SM CementMortar Lining of Water Pipelines in Place4 In. (100 mm) and Larger Effective date: May 1, 2017. First edition approved by AWWA Board of Directors June 17, 1955. This edition approved Jan. 14, 2017. Approved by American National Standards Institute Jan. 24, 2017. ANSI/AWWA C602

2、-17 (Revision of ANSI/AWWA C602-11) Copyright 2017 American Water Works Association. All Rights Reserved. ii AWWA Standard This document is an American Water Works Association (AWWA) standard. It is not a specification. AWWA standards describe minimum requirements and do not contain all of the engin

3、eering and administrative information normally contained in specifications. The AWWA standards usually contain options that must be evaluated by the user of the standard. Until each optional feature is specified by the user, the product or service is not fully defined. AWWA pub- lication of a standa

4、rd does not constitute endorsement of any product or product type, nor does AWWA test, certify, or approve any product. The use of AWWA standards is entirely voluntary. This standard does not supersede or take precedence over or displace any applicable law, regulation, or code of any governmental au

5、thority. AWWA standards are intended to represent a consensus of the water industry that the product described will provide satisfactory ser- vice. When AWWA revises or withdraws this standard, an official notice of action will be placed on the first page of the Official Notice section of Journal Am

6、erican Water Works Association. The action becomes effective on the first day of the month following the month of Journal American Water Works Association publication of the official notice. American National Standard An American National Standard implies a consensus of those substantially concerned

7、 with its scope and provisions. An American National Standard is intended as a guide to aid the manufacturer, the consumer, and the general public. The existence of an American National Standard does not in any respect preclude anyone, whether that person has approved the standard or not, from manuf

8、acturing, marketing, purchasing, or using products, processes, or proce - dures not conforming to the standard. American National Standards are subject to periodic review, and users are cau- tioned to obtain the latest editions. Producers of goods made in conformity with an American National Standar

9、d are encouraged to state on their own responsibility in advertising and promotional materials or on tags or labels that the goods are produced in conformity with particular American National Standards. Caution n oti Ce : The American National Standards Institute (ANSI) approval date on the front co

10、ver of this standard indicates completion of the ANSI approval process. This American National Standard may be revised or withdrawn at any time. ANSI procedures require that action be taken to reaffirm, revise, or withdraw this standard no later than five years from the date of publication. Purchase

11、rs of American National Standards may receive current information on all standards by calling or writing the American National Standards Institute, 25 West 43rd Street, Fourth Floor, New York, NY 10036; 212.642.4900; or emailing infoansi.org. hours of work by your fellow water professionals. Revenue

12、 from the sales of this AWWA material supports ongoing product development. Unauthorized distribution, either electronic or photocopied, is illegal and hinders AWWAs mission to support the water community. This AWWA content is the product of thousands of ISBN-13, print: 978-1-62576-216-0 eISBN-13, e

13、lectronic: 978-1-61300-416-6 DOI: http:/dx.doi.org/10.12999/AWWA.C602.17 All rights reserved. No part of this publication may be reproduced or transmitted in any form or by any means, electronic or mechanical, including photocopy, recording, or any information or retrieval system, except in the form

14、 of brief excerpts or quotations for review purposes, without the written permission of the publisher. Copyright 2017 by American Water Works Association Printed in USA Copyright 2017 American Water Works Association. All Rights Reserved. iii Committee Personnel The Steel Water Pipe Manufacturers Te

15、chnical Advisory Committee (SWPMTAC) Task Group for C602, which developed this standard, had the following personnel at the time: Christopher Walsh, Chair Bruce J. Britton, Vice-Chair H.H. Bardakjian, Manufacturers Consultant, Glendale, Calif. (AWWA) B.J. Britton, W. Walsh Company, Attleboro, Mass.

16、(AWWA) R.J. Card, Manufacturers Consultant, Sugar Hill, Ga. (AWWA) D.P. Ebner, Heitkamp Inc., Watertown, Conn. (AWWA) J.E. Hohider, Heitkamp Inc., Watertown, Conn. (AWWA) B.D. Keil, Northwest Pipe Company, Draper, Utah (AWWA) J.L. Luka, American SpiralWeld Pipe Company, Columbia, S.C. (AWWA) C.J. Wa

17、lsh, W. Walsh Company, Attleboro, Mass. (AWWA) The AWWA Standards Committee on Steel Pipe, which reviewed and approved this standard, had the following personnel at the time of approval: John H. Bambei Jr., Chair Dennis A. Dechant, Vice-Chair John L. Luka, Secretary General Interest Members J.H. Bam

18、bei Jr., Bambei Engineering Services, Arvada, Colo. (AWWA) W.R. Brunzell, Brunzell Associates Ltd., Skokie, Ill. (AWWA) R.J. Card, Lockwood, Andrews limits of pipeline shutdowns, if service requirements make these limits necessary; location of access manholes; location, type, and size of valves; location of interconnecting pipelines, hydrant branches, and service pipes; location of * Both publications available from National Academy of Sciences, 500 Fifth Street, NW, Washington, DC 20001. Copyright 2017 American Water Works Association. All Rights Reserved.