ANSI CSA AM Z21.12-1990 Draft Hoods (Fifth Edition).pdf

1、ANSI Z21.12-1990(reaffirmed 2015)Draft HoodsLegal Notice for StandardsCanadian Standards Association and CSA America, Inc. (operating as “CSA Group”) develop standards thro ugh a consensus standardsdevelopment pro cess approved by the Standards Council of Canada and the American National Standards I

2、nstitut e. This process bringstogether volunteer s representing varied viewpoints and interes ts to achieve consensus and develop a standard. Although CSA Groupadminist ers the process and est ablishes rules to pro mote fairness in achieving consensus, it does not independently tes t, evaluat e, or

3、verify thecontent of standards.Disclaimer and exclusion of liabilityThis document is pro vided without any representations, warranties, or conditions of any kind, express or implied, including, without limitation,implied warranties or conditions concerning this document s fitness for a particular pu

4、rpose or use, its merchantability , or its non-infringementof any third party s intellectual pro perty rights. CSA Group does not warrant the accuracy , complet eness, or currency of any of the informationpublished in this document. CSA Group makes no representations or warranties regarding this doc

5、ument s compliance with any applicablestatut e, rule, or regulation.IN NO EVENT SHALL CSA GROUP, ITS VOLUNTEERS, MEMBERS, SUBSIDIARIES, OR AFFILIATED COMPANIES, OR THEIR EMPLOYEES, DIRECTORS,OR OFFICERS, BE LIABLE FOR ANY DIRECT, INDIRECT, OR INCIDENTAL DAMAGES, INJURY, LOSS, COSTS, OR EXPENSES, HOW

6、SOEVER CAUSED,INCLUDING BUT NOT LIMITED TO SPECIAL OR CONSEQUENTIAL DAMAGES, LOST REVENUE, BUSINESS INTERRUPTION, LOST OR DAMAGEDDATA, OR ANY OTHER COMMERCIAL OR ECONOMIC LOSS, WHETHER BASED IN CONTRACT, TORT (INCLUDING NEGLIGENCE), OR ANY OTHERTHEORY OF LIABILITY, ARISING OUT OF OR RESULTING FROM A

7、CCESS TO OR POSSESSION OR USE OF THIS DOCUMENT, EVEN IF CSA GROUPHAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES, INJURY, LOSS, COSTS, OR EXPENSES.In publishing and making this document available, CSA Group is not undertaking to render pro fessional or other services for or on behalf of anyperso

8、n or entity or to perform any duty owed by any person or entity to another person or entity . The information in this document is directedto those who have the appropriat e degree of experience to use and apply its conten ts, and CSA Group accepts no responsibility whatsoeverarising in any way from

9、any and all use of or reliance on the information contained in this document.CSA Group is a private not -for -profit company that publishes voluntary standards and related documents. CSA Group has no power , nor does itundertake, to enforce compliance with the contents of the standards or other docu

10、ments it publishes.Intellectual property rights and ownershipAs between CSA Group and the users of this document (whether it be in print ed or electronic form), CSA Group is the owner , or the authorizedlicensee, of all works contained herein that are pro tect ed by copyright, all trade-marks (excep

11、t as otherwise not ed to the contrary), and allinventions and trade secrets that may be contained in this document, whether or not such inventions and trade secrets are prot ected bypatents and applications for patents. Without limitation, the unauthorized use, modification, copying, or disclosure o

12、f this document mayviolate laws that pro tect CSA Groups and/or other s int ellectual property and may give rise to a right in CSA Group and/or others to seek legalredress for such use, modification, copying, or disclosure. To the extent permitt ed by licence or by law , CSA Group reserves all int e

13、llectualproperty rights in this document.Patent rightsAtt ention is drawn to the possibility that some of the elements of this standard may be the subject of patent rights. CSA Group shall not beheld responsible for identifying any or all such patent rights. Users of this st andard are expressly adv

14、ised that determ ination of the validity ofany such patent rights is entirely their own responsibility .Authorized use of this documentThis document is being provided by CSA Group for informational and non-commercial use only . The user of this document is authorized to doonly the following:If this

15、document is in electronic form: load this document onto a computer for the sole purpose of reviewing it; search and bro wse this document; and print this document if it is in PDF format.Limited copies of this document in print or paper form may be distribut ed only to persons who are authorized by C

16、SA Group to have suchcopies, and only if this Legal Notice appear s on each such copy .In addition, users may not and may not permit others to alter this document in any way or remove this Legal Notice from the attached standard; sell this document without authorization from CSA Group; or make an el

17、ectronic copy of this document.If you do not agree with any of the terms and conditions contained in this Legal Notice, you may not load or use this document or make anycopies of the contents hereof, and if you do make such copies, you are required to destr oy them immediately . Use of this document

18、constitut es your acceptance of the terms and conditions of this Legal Notice.Standards Update ServiceANSI Z21.12-1990January 1990Title: Draft HoodsTo regist er for e-mail notification about any updat es to this publication go to shop.csa.ca click on CSA Updat e ServiceThe List ID that you will need

19、 to regist er for updat es to this publication is 2008222.If you require assista nce, please e-mail t echsupportcsagr oup.org or call 416-747-2233.Visit CSA Gr oups policy on privacy at www .csagr oup.org/legal to find out how we prot ect yourper sonal information.Fifth Edition - 1990 Approved Janua

20、ry 22,199O AMERICAN NATIONAL STANDARDS INSTITUTE, INC. Printed in U.S.A. American Gas Association Laboratories 8501 East Pleasant Valley Road Cleveland, Ohio 44131 Copyright 0 1990, American Gas Association Permission is granted to republish material herein in laws or ordinances, and in regulations,

21、 administrative orders, or similar documents issued by public authorities. Those desiring permission for other republication should consult the American Gas Association Laboratories, 8501 East Pleasant Valley Road, Cleveland, Ohio 44131. PREFACE This publication represents a standard for safe operat

22、ion, substantial and durable construction, and acceptable performance of draft hoods for gas appliances. It is the result of years of experience in the utilization of gas, supplemented by extensive research. Nothing in this standard is to be considered in any way as indicating a measure of quality b

23、eyond compliance with the provisions it contains. It is designed to allow compliance of draft hoods for gas appliances, the construction and performance of which may exceed the various provisions specified herein. In its preparation, full recognition has been given to possibilities of improvement th

24、rough ingenuity of design. As progress takes place, revisions may become necessary. When they are believed desirable, recommendations should be forwarded to the Chairman of Accredited Standards Committee Z21,8501 East Pleasant Valley Road, Cleveland, Ohio 44131. Safe and satisfactory operation of a

25、draft hood depends to a great extent upon its proper application to a gas-fired appliance installation, and it should only be installed on a properly operating appliance in accordance with the draft hood manufacturers installation instructions and local codes. General criteria for gas-fired applianc

26、e installations, including draft hoods, can be found in the National Fuel Gas Code, ANSI 2223.1, (NFPA 541, the Standard for Chimneys, Fireplaces, Vents and Solid Fuel Burning Appliances, ANSI/NFPA 211, and the Standard for Installation of Domestic Gas Conversion Burners, ANSI 221.8. CAUTION NOTICE:

27、 This American National Standard may be revised or withdrawn at any time. The procedures of the American National Standards Institute, Inc., require that action be taken to reaffirm, revise, or withdraw this standard no later than five (5) years from the date of approval. Purchasers of American Nati

28、onal Standards may receive current information on all standards by calling or writing the American National Standards Institute, Inc., 1430 Broadway, New York, N. Y. 10018, (212) 354-3300. EFFECTIVE DATE: An organization using this standard for product evaluation as a part of its certification progr

29、am will normally establish the date by which all products certified by that organization should comply with this standard. HISTORY OF THE DEVELOPMENT OF STANDARD FOR DRAFT HOODS (This History is informative and is not part of the standard.) Available records indicate that Sectional Committee 221 of

30、the American Standards Association was the first to undertake the development of construction and performance standards for draft hoods for use with gas-burning appliances. In December 1931, the 221 Committee authorized the appointment of a subcommittee to prepare such a standard. The Subcommittee o

31、n Listing Requirements for Draft Hoods held its initial meeting in April 1932. At the request of the subcommittee, the American Gas Association Laboratories conducted an extensive investigation relating to the design and performance of various types and sizes of draft hoods and reported its findings

32、 to the Committee. A draft standard for draft hoods was completed by the subcommittee and approved by the 221 Committee late in 1932. The draft standard was distributed to all interested parties and organizations for review and comment during December 1932. At its February 1933 meeting, the subcommi

33、ttee reviewed the draft standard in light of comments received. The revised draft standard was considered by the 221 Committee at its February 1933 meeting and certain portions of the draft standard were referred back to the subcommittee for further consideration and research. A further investigatio

34、n was made by the American Gas Association Laboratories to procure additional data and information concerning the points raised. Subsequently, the draft standard was modified by the subcommittee at its April 1933 meeting, approved by the 221 Committee at its June 1933 meeting and approved as the fir

35、st edition of the American Standard for Listing Requirements for Draft Hoods by the American Standards Association in September 1933. Certain types of draft hoods submitted to the American Gas Association Laboratories for listing under this standard indicated that the performance provisions were not

36、 applicable to all types of draft hoods. As a result, the subcommittee at its May 1935 meeting, requested the American Gas Association Laboratories to conduct a research investigation to provide information on the operation of draft hoods on gas converted central heating equipment and on gas water h

37、eaters. In September 1936, the subcommittee reviewed the results of this investigation and redrafted the entire performance section of the draft hood standard. The draft revisions were distributed for review and comment during October 1936. With some minor revisions, the revised standard was approve

38、d by the 221 Committee in June 1937 and the second edition of the draft hood standard was approved as American Standard by the American Standards Association in October 1937. At its March 1962 meeting, the 221 Committee reassigned supervision of the draft hood standard to the Subcommittee on Listing

39、 and Installation Requirements for Domestic Gas Conversion Burners, because the draft hood standard had been predicated on draft hoods for use on existing appliances converted to operation with gas. On August 24, 1966, the American Standards Association was reconstituted as the United States of Amer

40、ica Standards Institute, and on October 6,1969, was renamed the American National Standards Institute, Inc. As a result, the third edition of the draft hood standard, retitled American National Standard for Draft Hoods, was approved as American National Standard by the American National Standards In

41、stitute, Inc. in April 1971. At its July 1979 meeting, the conversion burner subcommittee, in response to requests, agreed to broaden the scope of the draft hood standard, which was predicated on draft hoods for use on appliances converted from other fuels to gas, to also cover replacement draft hoo

42、ds for use on gas-designed appliances. The draft standard, which was reorganized and expanded to be compatible with the draft hood coverage in the 221 appliance standards, was distributed for review and comment in January 1980. The subcommittee reconsidered the proposed standard at its July 1980 mee

43、ting in light of comments received and, with some modifications, recom- mended it to the 221 Committee The revised standard was approved by the 221 Committee at its April 1981 meeting. The fourth edition of the draft hood standard was approved as American National Standard by the American National S

44、tandards Institute, Inc., in November 1981. Following the procedures outlined above, further revisions to this standard were developed in line with industry developments. This, the fifth edition of the draft hood standard, was approved as American National Standard by the American National Standards

45、 Institute, Inc., on January 22,199O. ii Previous editions of the draft hood standard, and addenda thereto, approved by the American National Standards Institute or its predecessor organizations are as follows: 221.12-1933 221.12-1937 (R-1968) 221.12-1971 Z21.12a-1977 221.12-1981 Z21.12a-1983 NOTE:

46、This 1990 edition of 221.12 incorporates changes to the 1981 edition of 221.12 and addenda thereto. Changes, other than editorial, are denoted by a vertical line in the margin. . . . Ill ACCREDITED STANDARDS COMMITTEE 221 HOWARD I. FORMAN, Chairman WALTER H. JOHNSON, Vice Chairman F. G. HAMMAKER, Ad

47、ministrative Secretary (Non-Voting) REPRESENTING AIR-CONDITIONING CONTRACTORS OF AMERICA: James P. Norris REPRESENTING AMERICAN GAS ASSOCIATION: Charles D. Applequist Michael E. Griffin Richard L. Hendricks John R. Peak Jack Rea Robert D. Stegner Billy R. Ware REPRESENTING AMERICAN HOME ECONOMICS AS

48、SOCIATION: Frances Gailey REPRESENTING AMERICAN INSURANCE SERVICES GROUP, INC.: W. D. Malmstedt REPRESENTING AMERICAN PETROLEUM INSTITUTE: (Corresponding Member) Michael S. Hildebrand REPRESENTING AMERICAN PUBLIC GAS ASSOCIATION: Robert S. Cave REPRESENTING ASSOCIATION OF HOME APPLIANCE MANUFACTURER

49、S: Earl T. Rhinehart REPRESENTING THE CANADIAN GAS ASSOCIATION: Kenneth Bales Kevin Campbell (Alternate) REPRESENTING CONSUMERS UNION: George Papritz REPRESENTING FACTORY MUTUAL SYSTEM: James M. Simmons REPRESENTING GAS APPLIANCE MANUFACTURERS ASSOCIATION, INC.: Albert B. Chamberlain William E. Dalton Paul G. Daugirda Michael F. Gross0 J. R. Katchka Albert Morrison III Hal H. Rhea Ernest Wenczl REPRESENTING GENERAL SERVICES ADMINISTRATION, FEDERAL SUPPLY SERVICE: Dennis Davis David Shell (Alternate) INDIVIDUAL MEMBERS: Howard I. Forman R. Michael Martin REPRESENTING INTERNATION