ANSI CSA C22.2 NO.2556-15-2015 Wire and cable test methods (Fourth Edition).pdf

1、C22.2 No. 2556-15Wire and cable test methodsLegal Notice for StandardsCanadian Standards Association (operating as “CSA Group”) develops standards through a consensus standards development process approved by the Standards Council of Canada. This process brings together volunteers representing varie

2、d viewpoints and interests to achieve consensus and develop a standard. Although CSA Group administers the process and establishes rules to promote fairness in achieving consensus, it does not independently test, evaluate, or verify the content of standards.Disclaimer and exclusion of liabilityThis

3、document is provided without any representations, warranties, or conditions of any kind, express or implied, including, without limitation, implied warranties or conditions concerning this documents fitness for a particular purpose or use, its merchantability, or its non-infringement of any third pa

4、rtys intellectual property rights. CSA Group does not warrant the accuracy, completeness, or currency of any of the information published in this document. CSA Group makes no representations or warranties regarding this documents compliance with any applicable statute, rule, or regulation.IN NO EVEN

5、T SHALL CSA GROUP, ITS VOLUNTEERS, MEMBERS, SUBSIDIARIES, OR AFFILIATED COMPANIES, OR THEIR EMPLOYEES, DIRECTORS, OR OFFICERS, BE LIABLE FOR ANY DIRECT, INDIRECT, OR INCIDENTAL DAMAGES, INJURY, LOSS, COSTS, OR EXPENSES, HOWSOEVER CAUSED, INCLUDING BUT NOT LIMITED TO SPECIAL OR CONSEQUENTIAL DAMAGES,

6、 LOST REVENUE, BUSINESS INTERRUPTION, LOST OR DAMAGED DATA, OR ANY OTHER COMMERCIAL OR ECONOMIC LOSS, WHETHER BASED IN CONTRACT, TORT (INCLUDING NEGLIGENCE), OR ANY OTHER THEORY OF LIABILITY, ARISING OUT OF OR RESULTING FROM ACCESS TO OR POSSESSION OR USE OF THIS DOCUMENT, EVEN IF CSA GROUP HAS BEEN

7、 ADVISED OF THE POSSIBILITY OF SUCH DAMAGES, INJURY, LOSS, COSTS, OR EXPENSES.In publishing and making this document available, CSA Group is not undertaking to render professional or other services for or on behalf of any person or entity or to perform any duty owed by any person or entity to anothe

8、r person or entity. The information in this document is directed to those who have the appropriate degree of experience to use and apply its contents, and CSA Group accepts no responsibility whatsoever arising in any way from any and all use of or reliance on the information contained in this docume

9、nt.CSA Group is a private not-for-profit company that publishes voluntary standards and related documents. CSA Group has no power, nor does it undertake, to enforce compliance with the contents of the standards or other documents it publishes.Intellectual property rights and ownershipAs between CSA

10、Group and the users of this document (whether it be in printed or electronic form), CSA Group is the owner, or the authorized licensee, of all works contained herein that are protected by copyright, all trade-marks (except as otherwise noted to the contrary), and all inventions and trade secrets tha

11、t may be contained in this document, whether or not such inventions and trade secrets are protected by patents and applications for patents. Without limitation, the unauthorized use, modification, copying, or disclosure of this document may violate laws that protect CSA Groups and/or others intellec

12、tual property and may give rise to a right in CSA Group and/or others to seek legal redress for such use, modification, copying, or disclosure. To the extent permitted by licence or by law, CSA Group reserves all intellectual property rights in this document.Patent rightsAttention is drawn to the po

13、ssibility that some of the elements of this standard may be the subject of patent rights. CSA Group shall not be held responsible for identifying any or all such patent rights. Users of this standard are expressly advised that determination of the validity of any such patent rights is entirely their

14、 own responsibility.Authorized use of this documentThis document is being provided by CSA Group for informational and non-commercial use only. The user of this document is authorized to do only the following:If this document is in electronic form: load this document onto a computer for the sole purp

15、ose of reviewing it; search and browse this document; and print this document if it is in PDF format.Limited copies of this document in print or paper form may be distributed only to persons who are authorized by CSA Group to have such copies, and only if this Legal Notice appears on each such copy.

16、In addition, users may not and may not permit others to alter this document in any way or remove this Legal Notice from the attached standard; sell this document without authorization from CSA Group; or make an electronic copy of this document.If you do not agree with any of the terms and conditions

17、 contained in this Legal Notice, you may not load or use this document or make any copies of the contents hereof, and if you do make such copies, you are required to destroy them immediately. Use of this document constitutes your acceptance of the terms and conditions of this Legal Notice.Standards

18、Update ServiceC22.2 No. 2556-15December 2015Title: Wire and cable test methodsTo register for e-mail notification about any updates to this publication go to shop.csa.ca click on CSA Update ServiceThe List ID that you will need to register for updates to this publication is 2423696.If you require as

19、sistance, please e-mail techsupportcsagroup.org or call 416-747-2233.Visit CSA Groups policy on privacy at www.csagroup.org/legal to find out how we protect your personal information.Association of Standardization and CertificationNMX-J-556-ANCE-2015Fourth EditionCSA GroupCSA C22.2 No. 2556-15Fourth

20、 EditionUnderwriters Laboratories Inc.UL 2556Fourth EditionWire and Cable Test MethodsDecember 15, 2015ANSI/UL 2556-2015Commitment for AmendmentsThis standard is issued jointly by the Association of Standardization and Certification (ANCE), theCanadian Standards Association (operating as “CSA Group”

21、), and Underwriters Laboratories Inc. (UL).Comments or proposals for revisions on any part of the standard may be submitted to ANCE, CSAGroup, or UL at anytime. Revisions to this standard will be made only after processing according to thestandards development procedures of ANCE, CSA Group, and UL.

22、CSA Group and UL will issuerevisions to this standard by means of a new edition or revised or additional pages bearing their dateof issue. ANCE will incorporate the same revisions into a new edition of the standard bearing the samedate of issue as the CSA Group and UL pages.Copyright 2015 ANCERights

23、 reserved in favor of ANCE.ISBN 978-1-77139-930-2 2015 CSA GroupAll rights reserved. No part of this publication may be reproduced in any form whatsoever without theprior permission of the publisher.This Standard is subject to review five years from the date of publication, and suggestions for itsim

24、provement will be referred to the appropriate committee. To submit a proposal for change, pleasesend the following information to inquirescsagroup.org and include Proposal for change in thesubject line: Standard designation (number); relevant clause, table, and/or figure number; wording ofthe propos

25、ed change; and rationale for the change.To purchase CSA Group Standards and related publications, visit CSA Groups Online Store atshop.csa.ca or call toll-free 1-800-463-6727 or 416-747-4044.Copyright 2015 Underwriters Laboratories Inc.ULs Standards for Safety are copyrighted by UL. Neither a printe

26、d nor electronic copy of a Standardshould be altered in any way. All of ULs Standards and all copyrights, ownerships, and rights regardingthose Standards shall remain the sole and exclusive property of UL.This ANSI/UL Standard for Safety consists of the Fourth Edition including revisions through Dec

27、ember15, 2015. The most recent designation of ANSI/UL 2556 as an American National Standard (ANSI)occurred on December 15, 2015. ANSI approval for a standard does not include the Cover Page,Transmittal Pages, Title Page (front and back), or the Preface. The National Difference Page and IECForeword a

28、re also excluded from the ANSI approval of IEC-based standards.Comments or proposals for revisions on any part of the Standard may be submitted to UL at any time.Proposals should be submitted via a Proposal Request in ULs On-Line Collaborative StandardsDevelopment System (CSDS) at http:/.To purchase

29、 UL Standards, visit Comm 2000 at http:/m- call toll-free 1-888-853-3503.CONTENTSPREFACE 61 Scope .82 General 82.1 Units of measure .82.2 Normative references .82.3 Safety 112.4 Definitions 122.5 Test temperature 122.6 Reports 122.7 General requirements 133 Conductor tests 133.1 Conductor diameter 1

30、33.2 Cross-sectional area by mass (weight) method 143.3 Cross-sectional area by diameter method 223.4 DC resistance .233.5 Physical properties of conductors (tensile strength, elongation at break, and ultimatestrength) .253.6 High-current heat cycling for aluminum conductors 303.7 Length of lay 324

31、Insulation, overall covering, and jacket materials tests 334.1 Thickness 334.2 Physical properties (ultimate elongation and tensile strength) .384.3 Dry temperature rating of new materials (long-term aging test) 474.4 Carbon black content 495 Components tests 505.1 Coverage of fibrous braids 505.2 C

32、overage of shielding (wraps and braids) 515.3 Saturation 526 Electrical tests for finished wire and cable 536.1 Continuity 536.2 Dielectric voltage-withstand .556.3 Dielectric breakdown .586.4 Insulation resistance .596.5 Capacitance and relative permittivity .636.6 Stability factor .656.7 Spark 666

33、.8 Standard arcing test .696.9 Flex arcing test 706.10 Jacket resistance .736.11 AC leakage current test through insulation 746.12 AC leakage current test through jacket 766.13 Resistance of armor 777 Mechanical tests for finished wire and cable 787.1 Fall-in of extruded materials 787.2 Heat shock .

34、797.3 Heat shock resistance .817.4 Shrinkback .827.5 Shrinkback in air 837.6 Cold bend 84DECEMBER 15, 2015 NMX-J-556-ANCE-2015 CSA C22.2 NO. 2556-15 UL 2556 37.7 Cold impact .867.8 Deformation 887.9 Hot creep elongation and hot creep set 907.10 Abrasion resistance 937.11 Crush resistance .957.12 Cru

35、sh resistance (accelerated compression rate) .967.13 Impact resistance 987.14 Dielectric breakdown after glancing impact .1007.15 Flexibility at ROOM TEMPERATURE after aging 1027.16 Flexibility of separator tape under a jacket .1037.17 Flexibility of armored cable and metal-sheathed cable .1057.18 S

36、welling and blistering when immersed in liquid .1077.19 Durability of ink printing 1087.20 Color coating .1107.21 Mechanical strength .1127.22 Strength and elongation of cable in tension .1137.23 Bend test on nylon covered conductors 1147.24 Tightness of insulation .1157.25 Tightness of armor 1177.2

37、6 Flexing of shielded cables 1187.27 Mandrel pinch of -R cords 1207.28 Mandrel crush of -R cords 1217.29 Flexing of -R cords 1227.30 Armored cable bushing insertion 1248 Environmental tests for finished wire and cable .1258.1 Copper corrosion .1258.2 Ozone resistance 1278.3 Copper sulfate test for z

38、inc coatings on formed and unformed steel strip (preece test) .1309 Burning characteristics tests .1339.1 FT2/FH/Horizontal flame 1339.2 Burning particles (dropping) .1369.3 FT1.1379.4 FV-2/VW-1 1399.5 FV-1/Vertical flame .1429.6 Vertical tray flame tests (Method 1 Vertical tray and Method 2 FT4) 14

39、29.7 ST1 limited smoke 1489.8 Fire propagation/RPI 1519.9 Smoke emission .1559.10 Halogen acid gas emission .1599.11 Acid gas emission .1639.12 Flame test for portable cables/FT5 (United States and Canada only) 169Tables .171Figures 176Annex A (informative) Conductor removal from insulation for tubu

40、lar specimensA.1 Method 1: Stranded conductors 216A.2 Method 2: Stranded or solid conductors .216DECEMBER 15, 2015NMX-J-556-ANCE-2015 CSA C22.2 NO. 2556-15 UL 25564Annex B (informative) Determination of densityAnnex C (informative) Sample calculation for the determination of ultimate elongation or t

41、ensilestrength at 300 dC.1 Elongation .219C.2 Tensile strength 219Annex D (normative) Establishment of parameters and requirements for short-term air oven agingtestAnnex E (normative) Determination of temperature correction factorAnnex F (normative) Procedure and calculations for determining the deg

42、ree of coverage of fibrouscoveringsAnnex G (normative) Calculation of coverage of shielding (wraps and braids)Annex H (normative) Test enclosure and exhaust ductH.1 Test enclosure .232H.2 Exhaust duct .232H.3 Exhaust fan 232H.4 Air velocity measurements .233H.4.1 Within the exhaust duct .233H.4.2 Wi

43、thin the enclosure 234H.5 Smoke measuring equipment 234Annex I (informative) Conversion of pH to acid gas (as % HCl) and acid gas (as % HCl) to pHAnnex J (informative) Correlation of NMX wire and cable test method standards with UL 2556/CSAC22.2 No. 2556DECEMBER 15, 2015 NMX-J-556-ANCE-2015 CSA C22.

44、2 NO. 2556-15 UL 2556 5PREFACEThis is the harmonized ANCE, CSA Group, and UL standard for Wire and Cable Test Methods. It is theFourth edition of NMX-J-556-ANCE, the Fourth edition of CSA C22.2 No. 2556, and the Fourth edition ofUL 2556. This edition of NMX-J-556-ANCE supersedes the previous edition

45、 published on March 22, 2013.This edition of CSA C22.2 No. 2556 supersedes the previous edition published on March 22, 2013. Thisedition of UL 2556 supersedes the previous edition published on March 22, 2013.This harmonized standard was prepared by the Association of Standardization and Certificatio

46、n (ANCE),CSA Group, and Underwriters Laboratories Inc. (UL). The efforts and support of the TechnicalHarmonization Committee for Wire and Cable Test Methods, of the Council on the Harmonization ofElectrotechnical Standards of the Nations of the Americas (CANENA), are gratefully acknowledged.This Sta

47、ndard is considered suitable for use for conformity assessment within the stated scope of theStandard.The present Mexican standard was developed by the WG Metodos de Prueba para Conductores, from CT20 Conductores belonging the Comite de Normalizacin de la Asociacin de Normalizacin yCertificacin, A.C

48、., CONANCE, with the collaboration of the manufacturers and users of electricconductors.This standard was reviewed by the CSA Integrated Committee on Test Methods for Wires and Cables,under the jurisdiction of the CSA Technical Committee on Wiring Products and the CSA Strategic SteeringCommittee on

49、Requirements for Electrical Safety, and has been formally approved by the CSA TechnicalCommittee.This standard has been approved by the American National Standards Institute (ANSI) as an AmericanNational Standard.Where reference is made to a specific number of samples to be tested, the specified number is to beconsidered a minimum quantity.Note: Although the intended primary application of this standard is stated in its scope, it is important to note that it remainsthe responsibility of t