ANSI IEEE 1325-1996 Recommended Practice for Reporting Field Failure Data for Power Circuit Breakers《动力线路断路器场失效报告的推荐实施规程》.pdf

1、iIEEE Std 1325-1996 (R2008)IEEE Recommended Practice for Reporting Field Failure Data for Power Circuit BreakersSponsorSwitchgear Committeeof theIEEE Power Engineering SocietyReaffirmed 22 January 2003Approved 6 January 1997American National Standards InstituteReaffirmed 9 May 2008Approved 20 June 1

2、996IEEE Standards BoardAbstract: A format is presented that provides a concise and meaningful method for recording pertinentinformation on power circuit breaker field failures. It is recommended that this format be utilized in recordkeeping and directing corrective action to improve field reliabilit

3、y of power circuit breakers.Keywords: power circuit breakersThe Institute of Electrical and Electronics Engineers, Inc.345 East 47th Street, New York, NY 10017-2394, USACopyright 1996 by the Institute of Electrical and Electronics Engineers, Inc.All rights reserved. Published 1996. Printed in the Un

4、ited States of America.ISBN 1-55937-766-6No part of this publication may be reproduced in any form, in an electronic retrieval system or otherwise, wothout theprior written permission of the publisher.iiIEEE Standards documents are developed within the IEEE Societies and the Standards Coordinating C

5、ommittees ofthe IEEE Standards Board. Members of the committees serve voluntarily and without compensation. They are notnecessarily members of the Institute. The standards developed within IEEE represent a consensus of the broadexpertise on the subject within the Institute as well as those activitie

6、s outside of IEEE that have expressed an interestin participating in the development of the standard.Use of an IEEE Standard is wholly voluntary. The existence of an IEEE Standard does not imply that there are no otherways to produce, test, measure, purchase, market, or provide other goods and servi

7、ces related to the scope of the IEEEStandard. Furthermore, the viewpoint expressed at the time a standard is approved and issued is subject to changebrought about through developments in the state of the art and comments received from users of the standard. EveryIEEE Standard is subjected to review

8、at least every five years for revision or reaffirmation. When a document is morethan five years old and has not been reaffirmed, it is reasonable to conclude that its contents, although still of somevalue, do not wholly reflect the present state of the art. Users are cautioned to check to determine

9、that they have thelatest edition of any IEEE Standard.Comments for revision of IEEE Standards are welcome from any interested party, regardless of membership affiliationwith IEEE. Suggestions for changes in documents should be in the form of a proposed change of text, together withappropriate suppor

10、ting comments.Interpretations: Occasionally questions may arise regarding the meaning of portions of standards as they relate tospecific applications. When the need for interpretations is brought to the attention of IEEE, the Institute will initiateaction to prepare appropriate responses. Since IEEE

11、 Standards represent a consensus of all concerned interests, it isimportant to ensure that any interpretation has also received the concurrence of a balance of interests. For this reason,IEEE and the members of its societies and Standards Coordinating Committees are not able to provide an instantres

12、ponse to interpretation requests except in those cases where the matter has previously received formalconsideration.Comments on standards and requests for interpretations should be addressed to:Secretary, IEEE Standards Board445 Hoes LaneP.O. Box 1331Piscataway, NJ 08855-1331USAAuthorization to phot

13、ocopy portions of any individual standard for internal or personal use is granted by the Instituteof Electrical and Electronics Engineers, Inc., provided that the appropriate fee is paid to Copyright Clearance Center.To arrange for payment of licensing fee, please contact Copyright Clearance Center,

14、 Customer Service, 222 RosewoodDrive, Danvers, MA 01923 USA; (508) 750-8400. Permission to photocopy portions of any individual standard foreducational classroom use can also be obtained through the Copyright Clearance Center.Note: Attention is called to the possibility that implementation of this s

15、tandard may require use of subject mattercovered by patent rights. By publication of this standard, no position is taken with respect to the existence orvalidity of any patent rights in connection therewith. The IEEE shall not be responsible for identifying all patentsfor which a license may be requ

16、ired by an IEEE standard or for conducting inquiries into the legal validity orscope of those patents that are brought to its attention.iiiIntroduction(This introduction is not part of IEEE Std 1325-1996, IEEE Recommended Practice for Reporting Field Failure Data for PowerCircuit Breakers.)The relia

17、bility of installed equipment depends upon many factors, some of which are related to the installation,application, maintenance, and environment, while others are associated with the design, manufacture, and shipment ofthe equipment. Availability of improved information for meaningful feedback to th

18、e manufacturer or others is essentialto assure mutual understanding of any field failures encountered and the best practical corrective action.The High-Voltage Circuit Breaker Subcommittee of the IEEE Switchgear Committee recognized this need andestablished the Quality and Reliability Working Group.

19、 One of the results of this groups activities was thedevelopment of the Failure Reporting Form for power circuit breakers. This has been in trial use for several years, andit is now appropriate to elevate its status to a recommended practice.The Quality and Reliability Working Group of the High-Volt

20、age Circuit Breaker Subcommittee of the IEEESwitchgear Committee that prepared and approved this standard had the following membership:D. Sharma, Chair R. W. AlexanderD. M. BenensonW. J. BergmanJ. H. BrunkeS. DelisiR. L. DotsonP. W. DwyerK. I. GrayC. L. HandK. D. HendrixC. IsaacR. JacksonG. N. Leste

21、rJ. M. SailorsR. A. SarkinenM. SmithR. K. SmithH. E. SpindleA. D. StormsJ. TanneryJ. H. UgoThe following persons were on the High-Voltage Circuit Breaker Subcommittee that had oversight and approval of thisdocument:P. W. Dwyer, Chair R. W. AlexanderA. BosmaJ. H. BrunkeC. J. DvorakM. J. EckelkampR. D

22、. GarzonK. I. GrayH. L. HessD. S. JohnsonP. L. KolarikS. KuznetsovG. N. LesterR. W. LongA. K. McCabeG. F. MontilletD. E. ParrB. PatelD. F. PeeloG. O. PerkinsA. B. RishworthH. C. RossE. M. RuossG. St. JeanR. A. SarkinenD. SharmaH. M. SmithT. J. TobinE. F. VeverkaC. L. WagnerThe following persons were

23、 on the balloting committee:R. J. AltonJ. G. AngelisRichard H. ArndtSteve AtkinsonL. Ronald BeardHarvey L. BowlesMatthew BrownJohn H. BrunkeRaymond L. CapraAlexander DixonJ. J. DravisC. J. DvorakPeter W. DwyerRuben D. GarzonLouis W. GaussaKeith I. GrayKenneth HendrixH. L. HessW. E HoenigmannJerry M.

24、 JerabekP. L. KolarikDavid G. KumberaStephen R. LambertWard E. LaubachivJohn G. LeachGeorge N. LesterDon LottE. L. LuehringP. C. MayoAndrew K. McCabeLawrence V. McCallMichael S. McGuireWilliam C. McKayHarvey W. MikuleckyDon C. MillsAlec C. MonroeGeorges F. MontilletF. J. MuenchJames F. ODonnellRaymo

25、nd P. OLearyA. F. ParksDavid F. PeeloG. O. PerkinsR. Kris RanjanJ. C. RansomDavid N. ReynoldsH. C. RossTim E. RoysterGuy St. JeanL. H. SchmidtE. W. SchmunkC. A. SchwalbeDevki N. SharmaD. L. SwindlerJohn S. TanneryS. H. TelanderFrederick C. TeufelThomas J. TobinEdward F. VeverkaCharles L. WagnerWhen

26、the IEEE Standards Board approved this standard on 20 June 1996, it had the following membership:Donald C. Loughry, Chair Richard J. Holleman, Vice Chair Andrew G. Salem, Secretary Gilles A. BarilClyde R. CampJoseph A. CannatelliStephen L. DiamondHarold E. EpsteinDonald C. FleckensteinJay Forster*Do

27、nald N. HeirmanBen C. JohnsonE. G. “Al” KienerJoseph L. Koepfinger*Stephen R. LambertLawrence V. McCallL. Brace McClungMarco W. MigliaroMary Lou PadgettJohn W. PopeJose R. RamosArthur K. ReillyRonald H. ReimerGary S. RobinsonIngo RschJohn S. RyanChee Kiow TanLeonard L. TrippHoward L. Wolfman*Member

28、EmeritusAlso included are the following nonvoting IEEE Standards Board liaisons:Satish K. Aggarwal Alan H. Cookson Chester C. TaylorKristin M. DittmannIEEE Standards Project EditorvCLAUSE PAGE1. Overview.71.1 Scope 71.2 Purpose. 72. References.73. Definitions.84. Recommended practice .84.1 Backgroun

29、d 84.2 General . 84.3 Description of form 85. Implementation .86. Failure report utilization96.1 User 96.2 Manufacturer 97. Bibliography107IEEE Recommended Practice for Reporting Field Failure Data for Power Circuit Breakers1. OverviewActual practices of power switchgear users in documenting field f

30、ailures and failures of switchgear and other powerdelivery products vary widely. In order to restore failed elements to service, the emphasis often is to “clean up” afailure quickly, losing important data that is critical to corrective action. There is a real need for more depth in recordkeeping to

31、improve reliability of power handling equipment. This recommended practice addresses this need.1.1 ScopeA Failure Reporting Form, figures 1 and 2, has been developed by the IEEE Switchgear Committee to improve thereliability of circuit breakers through uniform reporting of field failures. The use of

32、 this approach is the recommendedpractice for all users of power circuit breakers.1.2 PurposeThe use of the Failure Reporting Form, included in this document, is recommended to standardize reporting of fieldfailures and to use these experiences to improve the reliability of power circuit breakers.2.

33、 ReferencesThis recommended practice shall be used in conjunction with the following publications:IEEE Std C37.100-1992, IEEE Standard Definitions for Power Switchgear (ANSI). 11IEEE publications are available from the Institute of Electrical and Electronics Engineers, 445 Hoes Lane, P.O. Box 1331,

34、Piscataway, NJ 08855-1331, USA.8 Copyright 1998 IEEE All Rights ReservedIEEE Std 1325-1996 IEEE STANDARD FOR REPORTING FIELD FAILURE3. DefinitionsFor definitions applying to this standard, refer to IEEE Std C37.100-1992. 4. Recommended practice4.1 BackgroundThe form, figures 1 and 2, is derived from

35、 the experiences and with the approval of both manufacturers and users. Itsmain goals and requirements are to be simple to use, to define the field failure including its related environment, andto establish records and references for further analysis and action should the situation repeat itself or

36、as other factorssurface.4.2 GeneralDetails of the one-page reporting form have been carefully developed by users and manufacturers to arrive at an easy-to-use format that will contain enough information to understand the defined problem.Although serious systems-related failures will require engineer

37、ing input for figure 2, it is expected that the fieldmaintenance person will complete the front side of the form, figure 1. The back side, figure 2, should be completed bythe users maintenance personnel with assistance, if required, from others.The completed form, figures 1 and 2, should be sent to

38、the person in the users organization who monitors fieldperformance of installed equipment. It should be used to analyze the reported failures and communicate incident-specific information to the manufacturer, as appropriate, when there is a repetitive or serious problem.4.3 Description of formThe fr

39、ont side, figure 1, is to be filled out for all failures and is an adequate report for minor malfunctions,nonconformances, or nonsystem related failures.The back side, figure 2, is useful for further elaboration of major failures that are more complex, with considerationgiven to system interaction.B

40、oth figures may be incorporated on a single sheet of paper and bound into pads for easy availability.5. ImplementationUsers should use this form, figures 1 and 2, as a record and feedback system to improve equipment reliability.Every effort should be made to promptly obtain and sort reports so that

41、failures are prioritized to identify thosedeserving the most immediate attention. The success of this activity depends on a cooperative effort between the usersmaintenance and operations people and the original manufacturer, when their involvement is needed.The front side, figure 1, should be filled

42、 out by maintenance personnel. A minimum of instruction or guidance isrequired.Copyright 1998 IEEE All Rights Reserved 9DATA FOR POWER CIRCUIT BREAKERS IEEE Std 1325-1996The questions should be answered and other details recorded at the job site soon after the failure occurs. It isrecommended that t

43、hese data be recorded before any repair work is initiated so as not to lose valuable clues on theorigin of the problem as the repair work is carried out.System Interaction, the back side, figure 2, is more complex and may require engineering analysis to provide the data.6. Failure report utilization

44、6.1 UserThe user can utilize the failure reportsa) To establish or supplement existing systems to keep specific, uniform, and informative records of fieldfailures.b) To provide data reports that can be sorted by manufacturer, model of equipment, age of equipment, similarityof application, etc. Data

45、could be computerized for sorting and analysis.c) To provide data that can be used to analyze failures, and find trends or problems that should be reported to themanufacturer.d) To provide data that can be used to study specific failures involving application conditions and maintenancepractices.e) T

46、o communicate to the manufacturer problems that require technical analysis and recommendation.6.2 ManufacturerThe manufacturer can use the summary of failure reports to assist ina) Studying field equipment failures to recognize trends based on the total breaker population.b) Investigating those fail

47、ures and suggesting corrective action. The action may result in changes in design,quality, application, shipping installation, or maintenance practices.c) Preparing and publishing suggestions for increasing reliability and reducing unplanned maintenance.It is very important that each user carefully

48、review all failure reports and send reports to the manufacturer that showserious or repetitive failures. By sending only selected reports to the manufacturer, the volume of reports is kept at aminimum and allows time for analysis of all problems. Generally, the newer the equipment, the larger the pe

49、rcentageof failure reports that should be sent to the manufacturer. Failures of older equipment are much more difficult toanalyze as long-term maintenance records may not be available.The use of this form does not eliminate the need for qualified technical personnel, both user and manufacturer, toinvestigate any major equipment problem. The use of this reporting format to improve reliability is meant tosupplement, but not to supersede, normal warranty or customer service policies. One of the major contributions of thisformat is to provide better data. It is recognized that t