ANSI IEEE C37.013A-2007 AC High Voltage Generator Circuit Breakers Rated on a Symmetrical Current Basis Amendment 1 Supplement for Use with Generators Rated 10 C100 MVA.pdf

1、IEEE Std C37.013a-2007(Amendment to IEEE Std C37.013-1997)IEEE Standard for AC High VoltageGenerator Circuit Breakers Rated ona Symmetrical Current BasisAmendment 1: Supplement for Use with Generators Rated 10100 MVAI E E E3 Park Avenue New York, NY 10016-5997, USA6 June 2007IEEE Power Engineering S

2、ocietySponsored by theSwitchgear CommitteeIEEE Std C37.013a-2007 IEEE Standard for AC High Voltage Generator Circuit Breakers Rated on a Symmetrical Current Basis Amendment 1: Supplement for Use with Generators Rated 10100 MVA Sponsor Switchgear Committee of the IEEE Power Engineering Society Approv

3、ed 8 March 2007 IEEE-SA Standards Board The Working Group thanks the International Electrotechnical Commission (IEC) for permission to reproduce information from its International Standard IEC 60694 (2002) and IEC 602271-100 (2006). All such extracts are copyright of IEC, Geneva, Switzerland. All ri

4、ghts reserved. Further information on the IEC is available from www.iec.ch. IEC has no responsibility for the placement and context in which the extracts and contents are reproduced by the author, nor is IEC in any way responsible for the other content or accuracy therein. Abstract: This amendment i

5、ncludes special requirements better suited for generator circuit breakers used to protect smaller generators rated between 10 MVA and 50 MVA and between 50 MVA and 100 MVA. It is important because the existing standards for typical distribution circuit breakers specifically exclude generator circuit

6、 breakers from the scope. Keywords: circuit breaker, generator, generator circuit breaker, high voltage, transformer _ The Institute of Electrical and Electronics Engineers, Inc. 3 Park Avenue, New York, NY 10016-5997, USA Copyright 2007 by the Institute of Electrical and Electronics Engineers, Inc.

7、 All rights reserved. Published 6 June 2007. Printed in the United States of America. IEEE is a registered trademark in the U.S. Patent +1 978 750 8400. Permission to photocopy portions of any individual standard for educational classroom use can also be obtained through the Copyright Clearance Cent

8、er. iv Copyright 2007 IEEE. All rights reserved. Introduction The 1997 edition of IEEE Std C37.013, although approved as an IEEE Standard, failed to win approval as an ANSI standard because, although the Scope says that it covers “all ac high-voltage generator circuit breakers,” the requirements for

9、 small generator circuit breakers were not adequately addressed. It is the main purpose of this supplement to add specific requirements for smaller generator circuit applications, and focusing in particular on circuit breakers for use with generators rated in the 10 MVA to 100 MVA range. The supplem

10、ent includes additional preferred ratings as well as other requirements that supplement the main requirements of 1997 edition. One important addition can be found in Annex B, which gives guidance regarding the effects of cable connections on the transient recovery voltage requirements for generator

11、circuits. It would be well to mention two items, which were proposed for change, but in the end were not incorporated: a) It was proposed that in 5.5 of IEEE Std C37.013-1997, an alternative rated short-circuit duty cycle, CO 30 s CO, should be added to the existing preferred duty cycle of CO 30 min

12、 CO. After much discussion, it was decided that, even if circuit breakers were available with the faster 30 s reclosing time, most likely it would never be needed. If there were a fault on either the transformer-side or the generator-side of the circuit breaker, it would be highly unlikely that such

13、 a fault could clear itself, so that an attempted reclosing operation would probably be unsuccessful anyway. Furthermore, it would take at least 30 minutes for someone to go to check the circuit to verify whether it should be reclosed. Therefore, the “CO 30 min CO” remains the preferred duty cycle.

14、b) It was proposed that, in Figure 15 of IEEE Std C37.013-1997, the parameters u and t should be defined for the coordinates of the upper end point on the “delay line” and that preferred values should be established for those parameters. After much discussion, it was concluded that, as the transient

15、 recovery voltage wave will have begun to bend away from the upper end of the delay line, the actual end point is not critical, and therefore, it is not specified. Notice to users Errata Errata, if any, for this and all other standards can be accessed at the following URL: http:/ standards.ieee.org/

16、reading/ieee/updates/errata/index.html. Users are encouraged to check this URL for errata periodically. Interpretations Current interpretations can be accessed at the following URL: http:/standards.ieee.org/reading/ieee/interp/ index.html. This introduction is not part of IEEE Std C37.013a-2007, IEE

17、E Standard for AC High Voltage Generator Circuit Breakers Rated on a Symmetrical Current BasisAmendment 1: Supplement for use with Generators Rated 10100 MVA. v Copyright 2007 IEEE. All rights reserved. Patents Attention is called to the possibility that implementation of this amendment may require

18、use of subject matter covered by patent rights. By publication of this amendment, no position is taken with respect to the existence or validity of any patent rights in connection therewith. The IEEE shall not be responsible for identifying patents or patent applications for which a license may be r

19、equired to implement an IEEE standard or for conducting inquiries into the legal validity or scope of those patents that are brought to its attention. Participants At the time this amendment was completed, the Small Generator Circuit Breaker Supplement Working Group had the following membership: R.

20、William Long, Chair Anne Bosma Dieter Braun Denis Dufournet Georges Montillet Neal McCord Nigel P. McQuin Martin Motz Erich Ruoss H. Melvin Smith Gerald J. Watson The following members of the individual balloting committee voted on this amendment. Balloters may have voted for approval, disapproval,

21、or abstention. Roy Alexander W. J. (Bill) Bergman Stan Billings Anne Bosma Dieter Braun Lyne Brisson Ted Burse Tommy Cooper Ronald Daubert Dufournet Denis Alexander Dixon Doug Edwards Gary Engmann Marcel Fortin William G. Fossey Ruben Garzon Douglas Giraud Keith Gray Randall Groves Erik Guillot Haro

22、ld L. Hess Edward Horgan Jr. David Jackson Richard Jackson Jerry Jerabek Stephen R. Lambert John Leach Jason Lin Albert Livshitz Franco Lo Monaco R. William Long Gregory Luri William Majeski Neil McCord Nigel P. McQuin Gary Michel Daleep Mohla Georges Montillet Arun Narang Jeffrey Nelson Paul Notari

23、an T. W. Olsen Miklos Orosz David Peelo Ralph Philbrook III James Ruggieri Devki Sharma Jordan Shikoski H. Melvin Smith R. Kirkland Smith Allan St. Peter Stanton Telander Shanmugan Thamilarasan Gerald Vaughn Charles Wagner James Wilson Zhenxue Xu vi Copyright 2007 IEEE. All rights reserved. When the

24、 IEEE-SA Standards Board approved this amendment on 8 March 2007, it had the following membership: Steve M. Mills, Chair Richard H. Hulett, Vice Chair Don Wright, Past Chair Judith Gorman, Secretary Richard DeBlasio Alex Gelman William R. Goldbach Arnold M. Greenspan Robert M. Grow Joanna N. Guenin

25、Julian Forster* Kenneth S. Hanus William B. Hopf Herman Koch Joseph L. Koepfinger* John Kulick David J. Law Glenn Parsons Ronald C. Petersen Tom A. Prevost Narayanan Ramachandran Greg Ratta Robby Robson Anne-Marie Sahazizian Virginia C. Sulzberger Malcolm V. Thaden Richard L. Townsend Walter Weigel

26、Howard L. Wolfman*Member Emeritus Also included are the following nonvoting IEEE-SA Standards Board liaisons: Satish K. Aggarwal, NRC Representative Richard DeBlasio, DOE Representative Alan H. Cookson, NIST Representative Don Messina IEEE Standards Program Manager, Document Development Matthew J. C

27、eglia IEEE Standards Program Manager, Technical Program Development vi Copyright 2007 IEEE. All rights reserved. Contents 1. Scope 1 2. References 2 5. Ratings and required capabilities 2 5.3 Rated continuous current . 2 5.8 Short-circuit current rating 3 5.10 Rated load current switching capability

28、. 7 5.12 Out-of-phase current switching ability 9 6. Tests . 10 7. Application guide . 12 8. Bibliography. 12 Annex B (informative) For generator circuit breakers connected to the step-up transformer by shielded cablesan example of the effects of added capacitance on TRV requirements for a system-so

29、urce fault. 13 1 Copyright 2007 IEEE. All rights reserved. IEEE Standard for AC High Voltage Generator Circuit Breakers Rated on a Symmetrical Current Basis Amendment 1: Supplement for Use with Generators Rated 10100 MVA NOTEThe editing instructions contained in this amendment define how to merge th

30、e material contained herein into the existing base standard and its amendments to form the comprehensive standard. The editing instructions are shown in bold italic. Four editing instructions are used: change, delete, insert, and replace. Change is used to make corrections in existing text or tables

31、. The editing instruction specifies the location of the change and describes what is being changed by using strikethrough (to remove old material) and underscore (to add new material). Delete removes existing material. Insert adds new material without disturbing the existing material. Insertions may

32、 require renumbering. If so, renumbering instructions are given in the editing instruction. Replace is used to make changes in figures or equations by removing the existing figure or equation and replacing it with a new one. Editorial notes will not be carried over into future editions because the c

33、hanges will be incorporated into the base standard. 1. Scope Change the existing paragraph as shown: This standard applies to all ac high-voltage generator circuit breakers rated on a symmetrical current basis that are installed between the generator and the transformer terminals. Requirements relat

34、ive to ac high-voltage generator circuit breakers intended for use with generators and transformers rated 10 MVA or more are covered specifically. Generator circuits rated less than 10 MVA and pumped storage installations are considered a special applications, and their requirements are not complete

35、ly covered by this standard. IEEE Std C37.013a-2007 IEEE Standard for AC High Voltage Generator Circuit Breakers Rated on a Symmetrical Current BasisAmendment 1: Supplement for use with Generators Rated 10100 MVA 2 Copyright 2007 IEEE. All rights reserved. 2. References Change the following referenc

36、es in Clause 2 as shown: ANSI C37.06-1987 2000(R1994), Switchgear: AC High-Voltage Circuit Breakers Rated on a Symmetrical Current BasisPreferred Ratings and Related Required Capabilities.1IEC 60694: 1996Edition 2.2 (2002-01), Common specifications for high voltage switchgear and controlgear standar

37、ds.2IEEE Std C37.04TM-19941999, IEEE Standard Rating Structure for AC High-Voltage Circuit Breakers Rated on a Symmetrical Current Basis (ANSI).3,4NEMA SG 4-19902000, Alternating Current High-Voltage Circuit Breaker.5Insert the following references into Clause 2 in alphanumeric order, and keep the e

38、xisting reference to the prior edition of IEEE Std C37.09TM-1979 that covers two-part testing: IEC 62271-100 Edition 1.1 (2003-05), High-voltage switchgear and controlgearPart 100: High-voltage alternating-current circuit-breakers. IEEE Std C37.09TM-1999, IEEE Standard Test Procedure for AC High-Vol

39、tage Circuit Breakers Rated on a Symmetrical Current Basis. IEEE Std C37.11TM-1997 (Reaff 2003), IEEE Standard Requirements for Electrical Control for AC High-Voltage Circuit Breakers Rated on a Symmetrical Current Basis or a Total Current Basis. 5. Ratings and required capabilities 5.3 Rated contin

40、uous current Change the following paragraph as shown: The rated continuous current of a generator circuit breaker is the designated upper limit of current in rms amperes at power frequency, which it shall be required to carry continuously without exceeding any of the limitations designated in 5.3.1

41、and 5.3.2. Typical values include 1.2 kA, 1.6 kA, 2 kA, 2.5 kA, 3.15 kA, 4 kA, 5 kA, 6.3 kA, 8 kA, 10 kA, 12 kA, 16 kA, 20 kA, etc and so on. 1ANSI publications are available from the Sales Department, American National Standards Institute, 25 West 43rd Street, 4th Floor, New York, NY 10036, USA (ht

42、tp:/www.ansi.org/). 2IEC publications are available from the Sales Department of the International Electrotechnical Commission, Case Postale 131, 3, rue de Varemb, CH-1211, Genve 20, Switzerland/Suisse (http:/www.iec.ch/). IEC publications are also available in the United States from the Sales Depar

43、tment, American National Standards Institute, 25 West 43rd Street, 4th Floor, New York, NY 10036, USA (http:/www.ansi.org/). 3IEEE publications are available from the Institute of Electrical and Electronics Engineers, Inc., 445 Hoes Lane, Piscataway, NJ 08854, USA (http:/standards.ieee.org/). 4The I

44、EEE standards or products referred to in this clause are trademarks of the Institute of Electrical and Electronics Engineers, Inc. 5NEMA publications are available from Global Engineering Documents, 15 Inverness Way East, Englewood, CO 80112, USA (http:/ IEEE Std C37.013a-2007 IEEE Standard for AC H

45、igh Voltage Generator Circuit Breakers Rated on a Symmetrical Current BasisAmendment 1: Supplement for use with Generators Rated 10100 MVA 3 Copyright 2007 IEEE. All rights reserved. 5.4.1 Dielectric strength of external insulation Replace Table 4 with the following: Table 4Schedule of dielectric st

46、rength values for ac generator circuit breakers and external insulation (Ref. IEC)a(Ref. ANSI) Insulation withstand voltagesbRated voltage (kV, rms) Rated maximum voltage (kV, rms) Power frequency (kV, rms) Lightning impulse 1.2 50 s wave (kV, peak) Line Column 1 Column 2 Column 3 Column 4 1 7.2 5 2

47、0 60 2 12 8.25 28 75 3 17.5 8.25 / 15 38 95 4 15.5 50 110 5 24 27 60 125 6 36 38 80 150ca Reprinted from 4.1.1 and Table 1a of IEC 60694 Ed. 2.2 “Copyright 2002 IEC, Geneva, Switzerland. www.iec.ch.” bFor rated voltages between those listed in Column 1 or in Column 2, the higher values of insulation

48、 withstand voltage should be chosen from the higher line number in the table. cIn Line 6 of Table 4, the Lightning Impulse Withstand Voltage value is not 170 kV, as no generators are rated 36 kV with a rated Lightning Impulse Withstand Voltage of 170 kV. 5.8 Short-circuit current rating Insert the f

49、ollowing text at the end of the existing paragraph: The short-circuit current rating of a generator circuit breaker is the rms symmetrical component of short-circuit current to which all required short-circuit capabilities are related. Procedures for determining the symmetrical short-circuit current duties that compare with ratings and related required capabilities are found in Clause 7. It is to be noted that, if the performance capability of a generator circuit breaker design has been de