ANSI IEEE N42.35-2016 American National Standard for Evaluation and Performance of Radiation Detection Portal Monitors for Use in Homeland Security.pdf

1、 American National Standard for Evaluation and Performance of Radiation Detection Portal Monitors for Use in Homeland Security Sponsored by the National Committee on Radiation Instrumentation, N42 IEEE 3 Park Avenue New York, NY 10016-5997 USA Accredited by the American National Standards Institute

2、ANSI N42.35-2016(Revision of ANSI N42.35-2006) ANSI N42.35-2016 (Revision of ANSI N42.35-2006) American National Standard for Evaluation and Performance of Radiation Detection Portal Monitors for Use in Homeland Security Sponsor National Committee on Radiation Instrumentation, N42 Accredited by the

3、American National Standards Institute Secretariat Institute of Electrical and Electronics Engineers, Inc. Approved 17 March 2016 American National Standards Institute 2 Copyright 2016 IEEE. All rights reserved. Abstract: Minimum performance specifications and testing methods for the evaluation of ra

4、diation portal monitors, also known as RPMs, are contained in this standard. These monitors are large-size permanently mounted-type instruments. These instruments are primarily designed for the detection of radioactive materials emitting gamma rays and neutrons. The specifications for general, radio

5、logical, environmental, electromagnetic and mechanical performance are given and the corresponding testing methods are described. The documentation to be provided by the manufacturer is listed as part of the requirements. A number of informative annexes that provide useful information and guidance i

6、n implementing this standard are also contained in this standard. Keywords: ANSI N42.35, documentation, gamma-rays, information and guidance, neutrons, performance specifications and testing, permanently mounted, radiation, radiation detection, radiation detection instruments, radiation portal monit

7、or, radioactive material The Institute of Electrical and Electronics Engineers, Inc. 3 Park Avenue, New York, NY 10016-5997, USA Copyright 2016 by The Institute of Electrical and Electronics Engineers, Inc. All rights reserved. Published 24 August 2016. Printed in the United States of America. IEEE

8、is a registered trademark in the U.S. Patent (978) 750-8400. Permission to photocopy portions of any individual standard for educational classroom use can also be obtained through the Copyright Clearance Center. 4 Copyright 2016 IEEE. All rights reserved. Important Notices and Disclaimers Concerning

9、 IEEE Standards Documents IEEE documents are made available for use subject to important notices and legal disclaimers. These notices and disclaimers, or a reference to this page, appear in all standards and may be found under the heading “Important Notice” or “Important Notices and Disclaimers Conc

10、erning IEEE Standards Documents.” Notice and Disclaimer of Liability Concerning the Use of IEEE Standards Documents IEEE Standards documents (standards, recommended practices, and guides), both full-use and trial-use, are developed within IEEE Societies and the Standards Coordinating Committees of t

11、he IEEE Standards Association (“IEEE-SA”) Standards Board. IEEE (“the Institute”) develops its standards through a consensus development process, approved by the American National Standards Institute (“ANSI”), which brings together volunteers representing varied viewpoints and interests to achieve t

12、he final product. Volunteers are not necessarily members of the Institute and participate without compensation from IEEE. While IEEE administers the process and establishes rules to promote fairness in the consensus development process, IEEE does not independently evaluate, test, or verify the accur

13、acy of any of the information or the soundness of any judgments contained in its standards. IEEE does not warrant or represent the accuracy or content of the material contained in its standards, and expressly disclaims all warranties (express, implied and statutory) not included in this or any other

14、 document relating to the standard, including, but not limited to, the warranties of: merchantability; fitness for a particular purpose; non-infringement; and quality, accuracy, effectiveness, currency, or completeness of material. In addition, IEEE disclaims any and all conditions relating to: resu

15、lts; and workmanlike effort. IEEE standards documents are supplied “AS IS” and “WITH ALL FAULTS.” Use of an IEEE standard is wholly voluntary. The existence of an IEEE standard does not imply that there are no other ways to produce, test, measure, purchase, market, or provide other goods and service

16、s related to the scope of the IEEE standard. Furthermore, the viewpoint expressed at the time a standard is approved and issued is subject to change brought about through developments in the state of the art and comments received from users of the standard. In publishing and making its standards ava

17、ilable, IEEE is not suggesting or rendering professional or other services for, or on behalf of, any person or entity nor is IEEE undertaking to perform any duty owed by any other person or entity to another. Any person utilizing any IEEE Standards document, should rely upon his or her own independe

18、nt judgment in the exercise of reasonable care in any given circumstances or, as appropriate, seek the advice of a competent professional in determining the appropriateness of a given IEEE standard. IN NO EVENT SHALL IEEE BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQU

19、ENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO: PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OU

20、T OF THE PUBLICATION, USE OF, OR RELIANCE UPON ANY STANDARD, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE AND REGARDLESS OF WHETHER SUCH DAMAGE WAS FORESEEABLE. Translations The IEEE consensus development process involves the review of documents in English only. In the event that an IEEE standa

21、rd is translated, only the English version published by IEEE should be considered the approved IEEE standard. 5 Copyright 2016 IEEE. All rights reserved. Official statements A statement, written or oral, that is not processed in accordance with the IEEE-SA Standards Board Operations Manual shall not

22、 be considered or inferred to be the official position of IEEE or any of its committees and shall not be considered to be, or be relied upon as, a formal position of IEEE. At lectures, symposia, seminars, or educational courses, an individual presenting information on IEEE standards shall make it cl

23、ear that his or her views should be considered the personal views of that individual rather than the formal position of IEEE. Comments on standards Comments for revision of IEEE Standards documents are welcome from any interested party, regardless of membership affiliation with IEEE. However, IEEE d

24、oes not provide consulting information or advice pertaining to IEEE Standards documents. Suggestions for changes in documents should be in the form of a proposed change of text, together with appropriate supporting comments. Since IEEE standards represent a consensus of concerned interests, it is im

25、portant that any responses to comments and questions also receive the concurrence of a balance of interests. For this reason, IEEE and the members of its societies and Standards Coordinating Committees are not able to provide an instant response to comments or questions except in those cases where t

26、he matter has previously been addressed. For the same reason, IEEE does not respond to interpretation requests. Any person who would like to participate in revisions to an IEEE standard is welcome to join the relevant IEEE working group. Comments on standards should be submitted to the following add

27、ress: Secretary, IEEE-SA Standards Board 445 Hoes Lane Piscataway, NJ 08854 USA Laws and regulations Users of IEEE Standards documents should consult all applicable laws and regulations. Compliance with the provisions of any IEEE Standards document does not imply compliance to any applicable regulat

28、ory requirements. Implementers of the standard are responsible for observing or referring to the applicable regulatory requirements. IEEE does not, by the publication of its standards, intend to urge action that is not in compliance with applicable laws, and these documents may not be construed as d

29、oing so. Copyrights IEEE draft and approved standards are copyrighted by IEEE under U.S. and international copyright laws. They are made available by IEEE and are adopted for a wide variety of both public and private uses. These include both use, by reference, in laws and regulations, and use in pri

30、vate self-regulation, standardization, and the promotion of engineering practices and methods. By making these documents available for use and adoption by public authorities and private users, IEEE does not waive any rights in copyright to the documents. Photocopies Subject to payment of the appropr

31、iate fee, IEEE will grant users a limited, non-exclusive license to photocopy portions of any individual standard for company or organizational internal use or individual, non-commercial use only. To arrange for payment of licensing fees, please contact Copyright Clearance Center, Customer Service,

32、222 Rosewood Drive, Danvers, MA 01923 USA; +1 978 750 8400. Permission to photocopy portions of any individual standard for educational classroom use can also be obtained through the Copyright Clearance Center. 6 Copyright 2016 IEEE. All rights reserved. Updating of IEEE Standards documents Users of

33、 IEEE Standards documents should be aware that these documents may be superseded at any time by the issuance of new editions or may be amended from time to time through the issuance of amendments, corrigenda, or errata. An official IEEE document at any point in time consists of the current edition o

34、f the document together with any amendments, corrigenda, or errata then in effect. Every IEEE standard is subjected to review at least every ten years. When a document is more than ten years old and has not undergone a revision process, it is reasonable to conclude that its contents, although still

35、of some value, do not wholly reflect the present state of the art. Users are cautioned to check to determine that they have the latest edition of any IEEE standard. In order to determine whether a given document is the current edition and whether it has been amended through the issuance of amendment

36、s, corrigenda, or errata, visit the IEEE-SA Website at http:/ieeexplore.ieee.org/xpl/standards.jsp or contact IEEE at the address listed previously. For more information about the IEEE-SA or IEEEs standards development process, visit the IEEE-SA Website at http:/standards.ieee.org. Errata Errata, if

37、 any, for all IEEE standards can be accessed on the IEEE-SA Website at the following URL: http:/standards.ieee.org/findstds/errata/index.html. Users are encouraged to check this URL for errata periodically. Patents Attention is called to the possibility that implementation of this standard may requi

38、re use of subject matter covered by patent rights. By publication of this standard, no position is taken by the IEEE with respect to the existence or validity of any patent rights in connection therewith. If a patent holder or patent applicant has filed a statement of assurance via an Accepted Lette

39、r of Assurance, then the statement is listed on the IEEE-SA Website at http:/standards.ieee.org/about/sasb/patcom/patents.html. Letters of Assurance may indicate whether the Submitter is willing or unwilling to grant licenses under patent rights without compensation or under reasonable rates, with r

40、easonable terms and conditions that are demonstrably free of any unfair discrimination to applicants desiring to obtain such licenses. Essential Patent Claims may exist for which a Letter of Assurance has not been received. The IEEE is not responsible for identifying Essential Patent Claims for whic

41、h a license may be required, for conducting inquiries into the legal validity or scope of Patents Claims, or determining whether any licensing terms or conditions provided in connection with submission of a Letter of Assurance, if any, or in any licensing agreements are reasonable or non-discriminat

42、ory. Users of this standard are expressly advised that determination of the validity of any patent rights, and the risk of infringement of such rights, is entirely their own responsibility. Further information may be obtained from the IEEE Standards Association. 7 Copyright 2016 IEEE. All rights res

43、erved. Participants At the time it approved this standard, the Accredited Standards Committee on Radiation Instrumentation, N42, had the following membership: Michael P. Unterweger, Chair Sue Vogel, Administrative Secretary Organization Represented Name of Representative Canberra Robert Huckins Comm

44、erce Dept., U.S. NIST Leticia Pibida Commerce Dept., U.S. NIST Michael P. Unterweger Consultant Frank X. Masse Department of Homeland SecurityPeter Shebell Harvard University Joseph Ring Health Physics Society .Wayne M. Glines Lawrence Berkeley National Laboratory .Edward J. Lampo Lawrence Livermore

45、 National Laboratory David Trombino NASA, GSFC Sachidananda R. Babu National Institute for Occupational Safety and Health Mark D. Hoover Oak Ridge National Laboratory . Peter J. Chiaro, Jr. Charles Britton (Alt.) ORTEC, Ametek Inc. Frank Sergent Pacific Northwest National Laboratory Richard Kouzes U

46、.S. Army Chad B. McKee Members-At-Large . Morgan Cox Edward Groeber Ronald M. Keyser Greg Komp Mark L. Maiello Joseph C. McDonald Joseph Stencel Edward Walker At the time this standard was completed, Subcommittee N42.HSI had the following membership: Morgan Cox, Co-Chair Michael P. Unterweger, Co-Ch

47、air Peter J. Chairo, Jr. David Gilliam Mark Hoover Cynthia G. Jones Ronald Keyser Joseph C. McDonald Leticia Pibida Peter Shebell David Trombino 8 Copyright 2016 IEEE. All rights reserved. At the time this standard was approved, the ANSI 42.35 Working Group had the following members: Leticia Pibida,

48、 Chair and Project Leader Peter J. Chiaro, Jr. Matthew Dallimore Paul Dimmerling Alexander Enders Robert Feuerbach Christina Forrester Bruce Geelhood Jeremiah Gruidl Jens Hovgaard Richard Kouzes Paul McGowan Dennis Leber Matthew Monetti Frank Sergent Martin Smith Arian Stoian David Trombino Eric Wag

49、ner 9 Copyright 2016 IEEE. All rights reserved. Introduction This introduction is not part of ANSI N42.35-2016, American National Standard for Evaluation and Performance of Radiation Detection Portal Monitors for Use in Homeland Security. This standard is the responsibility of the Accredited American Standards Committee on Radiation Instrumentation, N42. The standard was approved on N42 letter ballot. 10 Copyright 2016 IEEE. All rights reserved. Contents 1. Overview 12 1.1 Scope .12 1.2 Purpose 12 2. References 13 3. Definitions, acronyms, and abbreviations 13 3.1 Defin