ANSI INCITS ISO IEC 10373-6 AMD 5-2007 Identification cards Test methods Part 6 Proximity cards Amendment 5 Bit rates of fc 64 fc 32 and fc 16.pdf

1、INCITS/ISO/IEC 10373-6-2001/Amd.5-20072008(ISO/IEC 10373-6:2001/Amd.5:2007, IDT) Identification cards Test methods Part 6: Proximity cards Amendment 5: Bit ratesof fc/64, fc/32 and fc/16INCITS/ISO/IEC 10373-6-2001/Amd.5-20072008 (ISO/IEC 10373-6:2001/Amd.5:2007, IDT)INCITS/ISO/IEC 10373-6-2001/Amd.5

2、-20072008 ii ITIC 2008 All rights reserved PDF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobes licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer perform

3、ing the editing. In downloading this file, parties accept therein the responsibility of not infringing Adobes licensing policy. The ISO Central Secretariat accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to create this PDF

4、file can be found in the General Info relative to the file; the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event that a problem relating to it is found, please inform the Central Sec

5、retariat at the address given below. Adopted by INCITS (InterNational Committee for Information Technology Standards) as an American National Standard. Date of ANSI Approval: 8/4/2008 Published by American National Standards Institute, 25 West 43rd Street, New York, New York 10036 Copyright 2008 by

6、Information Technology Industry Council (ITI). All rights reserved. These materials are subject to copyright claims of International Standardization Organization (ISO), International Electrotechnical Commission (IEC), American National Standards Institute (ANSI), and Information Technology Industry

7、Council (ITI). Not for resale. No part of this publication may be reproduced in any form, including an electronic retrieval system, without the prior written permission of ITI. All requests pertaining to this standard should be submitted to ITI, 1250 Eye Street NW, Washington, DC 20005. Printed in t

8、he United States of America iiiForeword ISO (the International Organization for Standardization) and IEC (the International Electrotechnical Commission) form the specialized system for worldwide standardization. National bodies that are members of ISO or IEC participate in the development of Interna

9、tional Standards through technical committees established by the respective organization to deal with particular fields of technical activity. ISO and IEC technical committees collaborate in fields of mutual interest. Other international organizations, governmental and non-governmental, in liaison w

10、ith ISO and IEC, also take part in the work. In the field of information technology, ISO and IEC have established a joint technical committee, ISO/IEC JTC 1. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of the joint technical

11、 committee is to prepare International Standards. Draft International Standards adopted by the joint technical committee are circulated to national bodies for voting. Publication as an International Standard requires approval by at least 75 % of the national bodies casting a vote. Attention is drawn

12、 to the possibility that some of the elements of this document may be the subject of patent rights. ISO and IEC shall not be held responsible for identifying any or all such patent rights. Amendment 5 to ISO/IEC 10373-6:2001 was prepared by Joint Technical Committee ISO/IEC JTC 1, Information techno

13、logy, Subcommittee SC 17, Cards and personal identification. INCITS/ISO/IEC 10373-6-2001/Amd.5-20072008 ITIC 2008 All rights reserved1Identification cards Test methods Part 6: Proximity cards AMENDMENT 5: Bit rates of fc/64, fc/32 and fc/16 Page 2, 7.1.1 of ISO/IEC 10373-6:2001/Amd.2:2003 Add the fo

14、llowing note at the end of the subclause: “NOTE No load modulation test is required for bit rates of fc/64, fc/32 and fc/16.“ Page 4, 7.2.2 of ISO/IEC 10373-6:2001/Amd.2:2003 Replace the existing text with the following: “Tables 1 to 4 define additional test conditions to be applied for type A PICCs

15、 for different bit rates. NOTE The definitions for timing parameters related to the amplitude are different between fc/128 and higher bit rates, see the future Amendment 2 to ISO/IEC 14443-2:2001.“ Page 4, 7.2.2 of ISO/IEC 10373-6:2001/Amd.2:2003 Replace the title of Table 1 with the following: “Tab

16、le 1 Additional test conditions for a bit rate of fc/128“ Page 4, 7.2.2 of ISO/IEC 10373-6:2001/Amd.2:2003 Insert the following table and note after Table 1: Table 2 Additional test conditions for a bit rate of fc/64 Condition H (A/m) t1 t2 t3 a 1 1,5 20/fc 14/fc 6/fc 0,2 2 1,5 20/fc 16/fc 7/fc 0,05

17、 3 4,5 20/fc 14/fc 6/fc 0,2 4 4,5 20/fc 16/fc 7/fc 0,05 5 7,5 20/fc 14/fc 6/fc 0,2 6 7,5 20/fc 16/fc 7/fc 0,05 NOTE The timing t3 for all higher bit rates is defined in 8.1.2.2. Page 4, 7.2.2 of ISO/IEC 10373-6:2001/Amd.2:2003 Insert the following table after the new Table 2: INCITS/ISO/IEC 10373-6-

18、2001/Amd.5-20072008 ITIC 2008 All rights reserved2 Table 3 Additional test conditions for a bit rate of fc/32 Condition H (A/m) t1 t2 t3 a 1 1,5 10/fc 6/fc 6/fc 0,35 2 1,5 10/fc 7/fc 7/fc 0,15 3 4,5 10/fc 6/fc 6/fc 0,35 4 4,5 10/fc 7/fc 7/fc 0,15 5 7,5 10/fc 6/fc 6/fc 0,35 6 7,5 10/fc 7/fc 7/fc 0,15

19、 Page 4, 7.2.2 of ISO/IEC 10373-6:2001/Amd.2:2003 Insert the following table after Table 3: Table 4 Additional test conditions for a bit rate of fc/16 Condition H (A/m) t1 t2 t3 a 1 1,5 5/fc 3/fc 6/fc 0,6 2 1,5 5/fc 3/fc 7/fc 0,3 3 4,5 5/fc 3/fc 6/fc 0,6 4 4,5 5/fc 3/fc 7/fc 0,3 5 7,5 5/fc 3/fc 6/fc

20、 0,6 6 7,5 5/fc 3/fc 7/fc 0,3 Page 4, 7.2.2.1 of ISO/IEC 10373-6:2001/Amd.2:2003 Replace the existing text with the following: “Under the conditions defined in Table 1 the PICC shall answer to a REQA with ATQA. A PICC supporting the optional fc/64 bit rate shall operate under the conditions defined

21、in Table 2 after selection of a bit rate of fc/64. This PICC shall respond correctly to an I-block transmitted at a bit rate of fc/64. A PICC supporting the optional fc/32 bit rate shall operate under the conditions defined in Table 3 after selection of a bit rate of fc/32. The PICC shall respond co

22、rrectly to an I-block transmitted at a bit rate of fc/32. A PICC supporting the optional fc/16 bit rate shall operate under the conditions defined in Table 4 after selection of a bit rate of /16. The PICC shall respond correctly to an I-block transmitted at a bit rate of fc/16.“ Page 4, 7.2.2.2 of I

23、SO/IEC 10373-6:2001/Amd.2:2003 Replace the existing text with the following: “The test report shall confirm the intended operation at the mandatory fc/128 bit rate under the conditions defined in Table 1. For PICCs supporting one or more of the optional high bit rates the test report shall confirm t

24、he intended operation at the supported bit rates under the conditions defined in 7.2.2.1.“ fcINCITS/ISO/IEC 10373-6-2001/Amd.5-20072008 ITIC 2008 All rights reserved3Page 4, 7.2.3 of ISO/IEC 10373-6:2001/Amd.2:2003 Replace the existing text with the following: “Tables 5 to 7 define additional test c

25、onditions to be applied for type B PICCs for different bit rates. Page 4, 7.2.3 of ISO/IEC 10373-6:2001/Amd.2:2003 Replace the title of Table 2 (renumbered to Table 5) with the following: “Table 5 Additional test condition for bit rates of fc/128 and fc/64“ Page 4, 7.2.3 of ISO/IEC 10373-6:2001/Amd.

26、2:2003 Insert the following table after Table 5: Table 6 Additional test conditions for a bit rate of fc/32 Condition H (A/m) m (%) tr, tf(s) 1 1,5 8 1 2 1,5 14 1 3 4,5 8 1 4 4,5 14 1 5 7,5 8 1 6 7,5 14 1 Page 4, 7.2.3 of ISO/IEC 10373-6:2001/Amd.2:2003 Insert the following table after Table 6: Tabl

27、e 7 Additional test conditions for a bit rate of fc/16 Condition H (A/m) m (%) tr, tf(s) 1 1,5 8 0,8 2 1,5 14 0,8 3 4,5 8 0,8 4 4,5 14 0,8 5 7,5 8 0,8 6 7,5 14 0,8 Page 5, 7.2.3.1 of ISO/IEC 10373-6:2001/Amd.2:2003 Replace the existing text with the following: “Under the conditions defined in Table

28、5 the PICC operating at a bit rate of fc/128 shall answer to a REQB with ATQB. INCITS/ISO/IEC 10373-6-2001/Amd.5-20072008 ITIC 2008 All rights reserved4 A PICC supporting the optional fc/64 bit rate shall operate under the conditions defined in Table 5 after selection of a bit rate of fc/64. This PI

29、CC shall respond correctly to an I-block transmitted at a bit rate of fc/64. A PICC supporting the optional fc/32 bit rate shall operate under the conditions defined in Table 6 after selection of a bit rate of fc/32. The PICC shall respond correctly to an I-block transmitted at a bit rate of fc/32.

30、A PICC supporting the optional fc/16 bit rate shall operate under the conditions defined in Table 7 after selection of a bit rate of fc/16. The PICC shall respond correctly to an I-block transmitted at a bit rate of fc/16.“ Page 5, 7.2.3.2 of ISO/IEC 10373-6:2001/Amd.2:2003 Replace the existing text

31、 with the following: “The test report shall confirm the intended operation at the mandatory fc/128 bit rate under the conditions defined in Table 5. For PICCs supporting one or more of the optional high bit rates the test report shall confirm the intended operation at the supported bit rates under t

32、he conditions defined in 7.2.3.1.“ Page 14, A.2 Insert new A.2.1 after the notes and before Figure A.3 with the following title and move the existing Figure A.3 into new A.2.1: “A.2.1 Impedance matching network for a bit rate of fc/128“ Change the title of Figure A.3 to “Figure A.3 Impedance matchin

33、g network for a bit rate of fc/128“ Page 14, A.2 Insert new A.2.2 after new A.2.1 with the title “A.2.2 Impedance matching network for bit rates of fc/64, fc/32 and fc/16“ and insert the following figure into new A.2.2: 50 Ohm power driver impedance matching network Z=50 Ohm RantAntenna coil LantRex

34、tC1a C2 C3 C4 C1b Component Table: Value Unit Remarks C1a 56 pF Voltage range 200V C1b 5,6 pF Voltage range 200V C2 180 pF Voltage range 200V C3 15 pF Voltage range 200V C4 2-27 pF Voltage range 200V Rext 2 Ohm Power range 8 W NOTE This impedance matching network is designed for tests up to 7,5 A/m.

35、 Figure A.4 Impedance matching network for bit rates of fc/64, fc/32 and fc/16 INCITS/ISO/IEC 10373-6-2001/Amd.5-20072008 ITIC 2008 All rights reserved5Add the following new Annex J: Annex J (normative) High bit rate selection test methods for PCD J.1 Apparatus In this test the PCD-test-apparatus sh

36、all be configurable to change the bit rate during the test procedure. Tester shall be able to measure the bit rate used by the PCD on each stage of this test procedure. J.2 Procedure Place the PCD-test-apparatus into the field of the PCD. J.2.1 Procedure for Type A The following procedure shall be r

37、epeated for all values of interface byte TA(1) defined in Table J.1: a) Run through activation sequence as defined in ISO/IEC 14443-3. b) The PCD shall send a RATS command as defined in ISO/IEC 14443-4. c) The PCD-test-apparatus answers with a valid ATS including TA(1) according to Table J.1. d) The

38、 PCD may optionally send a PPS with a valid parameter setting for PPS1 byte according to Table J.1. e) If the PCD has sent a PPS then the PCD-test-apparatus acknowledges the received PPS with a valid PPS response. f) The PCD shall send I(0)0 block using the bit rate selected. NOTE This block may als

39、o be I(1)0, or R(NACK) in case of PICC presence check method 2a. g) The PCD-test-apparatus sends a valid responseusing the bit rate selected. Check, if the answer from the PCD-test apparatus is accepted by the PCD. Table J.1 Correct behaviour of PCD after ATS with TA(1) TA(1) Valid parameter setting

40、 for PPS1 (10000000)b (00000000)b a(10010001)b (00000101)b, (00000000)b (10100010)b (00001010)b, (00000000)(10110011)b (00000101)b, (00001010)b, (00000000)b (11000100)b (00001111)b, (00000000)b (11010101)b (00000101)b, (00001111)b, (00000000)b (11100110)b (00001010)b, (00001111)b, (00000000)b Last p

41、age INCITS/ISO/IEC 10373-6-2001/Amd.5-20072008 ITIC 2008 All rights reserved6 TA(1) Valid parameter setting for PPS1 (11110111)b (00000101)b, (00001010)b, (00001111)b, (00000000)b (00000000)b (00000000)b a(00000001)b (00000001)b, (00000000)b (00000010)b (00000010)b, (00000000)(00000011)b (00000001)b

42、, (00000010)b, (00000000)b (00000100)b (00000011)b, (00000000)b (00000101)b (00000001)b, (00000011)b, (00000000)b (00000110)b (00000010)b, (00000011)b, (00000000)b (00000111)b (00000001)b, (00000010)b, (00000011)b, (00000000)b (00010000)b (00000000)b (00000100)b (00010001)b (00000001)b, (00000000)b

43、(00000101)b, (00000100)b (00010010)b (00000010)b, (00000000)b (00000110)b, (00000100)b (00010011)b (00000001)b, (00000010)b, (00000000)b (00000101)b, (00000110)b, (00000100)b (00010100)b (00000011)b, (00000000)b (00000111)b, (00000100)b (00010101)b (00000001)b, (00000011)b, (00000000)b (00000101)b,

44、(00000111)b, (00000100)b (00010110)b (00000010)b, (00000011)b, (00000000)b (00000110)b, (00000111)b, (00000100)b (00010111)b (00000001)b, (00000010)b, (00000011)b, (00000000)b (00000101)b, (00000110)b, (00000111)b, (00000100)b (00100000)b (00000000)b (00001000)b (00100001)b (00000001)b, (00000000)b

45、(00001001)b, (00001000)b (00100010)b (00000010)b, (00000000)b (00001010)b, (00001000)b (00100011)b (00000001)b, (00000010)b, (00000000)b (00001001)b, (00001010)b, (00001000)b (00100100)b (00000011)b, (00000000)b (00001011)b, (00001000)b (00100101)b (00000001)b, (00000011)b, (00000000)b (00001001)b,

46、(00001011)b, (00001000)b (00100110)b (00000010)b, (00000011)b, (00000000)b (00001010)b, (00001011)b, (00001000)b (00100111)b (00000001)b, (00000010)b, (00000011)b, (00000000)b (00001001)b, (00001010)b, (00001011)b, (00001000)b (00110000)b (00000000)b (00000100)b (00001000)b (00110001)b (00000001)b,

47、(00000000)b (00000101)b, (00000100)b (00001001)b, (00001000)b INCITS/ISO/IEC 10373-6-2001/Amd.5-20072008 ITIC 2008 All rights reserved7TA(1) Valid parameter setting for PPS1 (00110010)b (00000010)b, (00000000)b (00000110)b, (00000100)b (00001010)b, (00001000)b (00110011)b (00000001)b, (00000010)b, (

48、00000000)b (00000101)b, (00000110)b, (00000100)b (00001001)b, (00001010)b, (00001000)b (00110100)b (00000011)b, (00000000)b (00000111)b, (00000100)b (00001011)b, (00001000)b (00110101)b (00000001)b, (00000011)b, (00000000)b (00000101)b, (00000111)b, (00000100)b (00001001)b, (00001011)b, (00001000)b

49、(00110110)b (00000010)b, (00000011)b, (00000000)b (00000110)b, (00000111)b, (00000100)b (00001010)b, (00001011)b, (00001000)b (00110111)b (00000001)b, (00000010)b, (00000011)b, (00000000)b (00000101)b, (00000110)b, (00000111)b, (00000100)b (00001001)b, (00001010)b, (00001011)b, (00001000)b (01000000)b (00000000)b (00001100)b (01000001)b (00000001)b, (00000000)b (00001101)b, (00001100)b (01000010)b (00000010)b, (00000000)b (00001110)b, (00001100)b (01000011)b (00000001)b, (00000010)b, (00000000)b (0