1、INCITS/ISO/IEC 14473:19992008 (ISO/IEC 14473:1999, IDT) Information technology Office equipment Minimum informationto be specified for image scannersINCITS/ISO/IEC 14473:19992008 (ISO/IEC 14473:1999, IDT)Copyright American National Standards Institute Provided by IHS under license with ANSI Not for
2、ResaleNo reproduction or networking permitted without license from IHS-,-,-INCITS/ISO/IEC 14473:19992008 ii ITIC 2008 All rights reserved PDF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobes licensing policy, this file may be printed or viewed but shall not be edite
3、d unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this file, parties accept therein the responsibility of not infringing Adobes licensing policy. The ISO Central Secretariat accepts no liability in this area. Adobe is a tra
4、demark of Adobe Systems Incorporated. Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodi
5、es. In the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below. Adopted by INCITS (InterNational Committee for Information Technology Standards) as an American National Standard. Date of ANSI Approval: 6/19/2008 Published by America
6、n National Standards Institute, 25 West 43rd Street, New York, New York 10036 Copyright 2008 by Information Technology Industry Council (ITI). All rights reserved. These materials are subject to copyright claims of International Standardization Organization (ISO), International Electrotechnical Comm
7、ission (IEC), American National Standards Institute (ANSI), and Information Technology Industry Council (ITI). Not for resale. No part of this publication may be reproduced in any form, including an electronic retrieval system, without the prior written permission of ITI. All requests pertaining to
8、this standard should be submitted to ITI, 1250 Eye Street NW, Washington, DC 20005. Printed in the United States of America Copyright American National Standards Institute Provided by IHS under license with ANSI Not for ResaleNo reproduction or networking permitted without license from IHS-,-,-iiiFo
9、rewordISO (the International Organization for Standardization) and IEC (the International Electrotechnical Commission)form the specialized system for worldwide standardization. National bodies that are members of ISO or IECparticipate in the development of International Standards through technical c
10、ommittees established by therespective organization to deal with particular fields of technical activity. ISO and IEC technical committeescollaborate in fields of mutual interest. Other international organizations, governmental and non-governmental, inliaison with ISO and IEC, also take part in the
11、work.In the field of information technology, ISO and IEC have established a joint technical committee, ISO/IEC JTC 1.Draft International Standards adopted by the joint technical committee are circulated to national bodies for voting.Publication as an International Standard requires approval by at le
12、ast 75 % of the national bodies casting a vote.International Standard ISO/IEC 14473 was prepared by ISO/IEC JTC 1, Information technology, SubcommitteeSC 28, Office equipment.Annex A of this International Standard is for information only.INCITS/ISO/IEC 14473:19992008 ITIC 2008 All rights reservedCop
13、yright American National Standards Institute Provided by IHS under license with ANSI Not for ResaleNo reproduction or networking permitted without license from IHS-,-,-Copyright American National Standards Institute Provided by IHS under license with ANSI Not for ResaleNo reproduction or networking
14、permitted without license from IHS-,-,-AMERICAN NATIONAL STANDARD INCITS/ISO/IEC 14473:199920081Information technology - Office equipment - Minimum informationto be specified for image scanners1 ScopeThis International Standard is intended to facilitate user selection of an image scanner. This Inter
15、national Standardspecifies the minimum information that shall be included by manufacturers in their specification sheets for scanners.This International Standard is made for the average end user. For this reason it does not describe all specificationsof scanners with special features such as double
16、sided scanning or high speed. By insuring consistency ofspecification of scanner product information, this International Standard enables the end user to make meaningfulcomparisons of machine functionality and performance characteristics. The most meaningful parameters of functionand performance are
17、 specified and defined, and measures of performance are provided.This International Standard further applies to types of scanners which are most prevalent in use, includingparameters for a scanning engine (an optomechanical physical device) and basic image processing only (thoseprocesses include dig
18、ital data output with encoded gray scale, or unencoded single bit plus halftone data). It does notrequire specification of advanced application processing such as OCR, translation, vector conversion, etc. Becausescanners use both software and/or hardware to achieve some scanner functions and control
19、s, the standard containssome entries related to software even though the standard is primarily for scanner hardware. The manufacturer, athis option, may include description of such additional functionality which may be provided. This standard also doesnot consider image quality, nor does it provide
20、or use related test targets.2 Normative referencesThe following standards contain provision which, through reference in this text, constitute provisions of thisInternational Standard. At the time of publication, the editions indicated were valid. All standards are subject torevision, and parties to
21、agreements based on this International Standard are encouraged to investigate the possibilityof applying the most recent editions of the standards indicated below. Members of IEC and ISO maintain registers ofcurrently valid International Standards.ISO 216:1975, Writing paper and certain classes of p
22、rinted matter - Trimmed sizes - A and B series.ISO 554:1976, Standard atmospheres for conditioning and/or testing - Specifications.ISO 7779:1988, Acoustics - Measurement of airborne noise emitted by computer and business equipment.ISO 9295:1988, Acoustics - Measurement of high-frequency noise emitte
23、d by computer and business equipment.ISO 9296:1988, Acoustics - Declared noise emission values of computer and business equipment.3 ConformanceIn order to comply with this International Standard, specification sheets shall contain, in the order shown, all itemslisted in clause 5 which are relevant t
24、o the machine being described.4 Test and measurement conditionsUnless otherwise specified, all tests and measurements made by the manufacturer to provide data for scannerspecification sheets satisfying this International Standard shall be conducted at the following conditions:- temperature: 18 C to
25、25 C- relative humidity 30% to 70%- voltage: rated input voltage- frequency: rated frequency- paper size: A4- paper weight: 60 g/m2to 90g/m2Whenever a capacity is given in sheets, the reference paper weight shall be specified. ITIC 2008 All rights reservedCopyright American National Standards Instit
26、ute Provided by IHS under license with ANSI Not for ResaleNo reproduction or networking permitted without license from IHS-,-,-25 Information to be included in the specification sheetsThe following table defines, for each parameter, the number, the name of the parameter, a short description of theen
27、try, and the measurement method. These constitute the information to be included in the specification sheets.The heading of the specification sheet shall indicate that it has been prepared in accordance with this InternationalStandard. The numbers and headings of the table in clause 5 shall be used.
28、 Parameters which are not applicablemay be ignored, without changing the number of other parameters.Parameter Description of the entry Remark and examples1 .General1.1 Name and Model Number Manufacturers name and ModelIdentification1.2 Scanner Type Flatbed, Sheet Feed, Handheld1.3 Sensing Capability
29、 Monochrome, Color1.4 Maximum Document Size _ mm x _ mmGive dimensions in millimeters orstandard sizes.1.5 Optical Resolution _ dots/25.4 mm (_ dpi)_ dots/mmIndicate the fundamental opticalsampling rate of the sensor.1.6 Interface SCSI, SCSI-2, CentronicsIEEE-488, RS-232CCommonly called interface na
30、mesas Centronics and RS-232C couldbe used.2. Scanning2.1 Scanning Time2.1.1 Page Scanning Time _seconds for 1 bit/pixel (line art)_seconds for 8 bit/pixel (256 gray)_seconds for 24 bit/pixel (color)Scanning time shall be measuredbetween start scanning and end ofscanning. The start scanning isdefined
31、 as pushing a start buttoneither in application software or for ahandheld scanner. The end of thescanning is defined as a time when ahost PC is released from thescanning job. The test configurationused shall be stated: PC modelname, memory size, interface,scanner driver and applicationsoftware.*FB,
32、SF : A4, Portrait, 150, 200 or300 dpi*HH : A4 or A6, Portrait, 150, 200 or300 dpiTo be specified if available.2.1.2 Line Scanning Time _ms/line The test configuration used shall bestated: resolution, color / 256 gray /line art etc.2.2 Scanning Speed _mm/s The test configuration used shall bestated:
33、resolution, color / 256 gray /line art etc.2.3 AD Converter Number of bits for AD conversion. 8-bit, 10-bit, 12-bit2.4 Image Sensor Type CCD, Contact typeNote*: FB=Flatbed scanner, SF=Sheet Feed Scanner, HH=Handheld ScannerINCITS/ISO/IEC 14473:19992008 ITIC 2008 All rights reservedCopyright American
34、 National Standards Institute Provided by IHS under license with ANSI Not for ResaleNo reproduction or networking permitted without license from IHS-,-,-)3Parameter Description of the entry Remark and examples2.5 Light Source Fluorescent lamp, LED, Halogenlamp, Color temperature and/orspectrum2.6 Co
35、lor Separation State color separation method used. R-G-B color sensorR-G-B light source switching2.7 Color Sequence 3-pass, 1-pass2.8 Drop-out Color Red, Yellow-Green3. Output3.1 Output Mode State output mode. R-G-B color, C-M-Y color, Grayscale, Line art, Dither, Error diffusionIndicate the matrix
36、size or thenumber of halftones, for dither anderror diffusion.3.2 Gray Scale Level Number of the Image Scanneroutput bits.8-bit, 12-bit, R-G-B bits for eachcolor.3.3 Color Sequence Dot sequential, Line sequential,Page sequential3.4 Output Resolution _dpiIndicate the value(s) or the range ofcalculate
37、d resolution.100/200/300 dpi 50-600 dpi3.5 Maximum Achievable OutputData Rate_ MB/secIndicate the value of maximumachievable output data rate by thescanner.Indicate the value at each interface.3.6 Average Achievable OutputData Rate_ MB/sec Indicate the value at each interface.The test configuration
38、used shall bestated : PC model name, memorysize, interface, scanner driver andapplication software.4. Additional Functions andControls Implemented byHardware or SoftwareState if functions are achievable byhardware or by software includedwith the scanner.4.1 Scaling _-_%Indicate the range of scaling
39、basedon the optical resolution.50-200%4.2 Contrast Indicate the range of contrastcontrol.0-255 levelsContrast means the ratio of imageand non-image area.4.3 Brightness Indicate the range of brightnesscontrol.0-255 levelsBrightness means the generaldensity of image.4.4 Others State other functions. C
40、ropping, Compression, Gammacorrection, Segmentation, Masking,Sharpness, Color correction,Automatic size sensing5. Automatic Document Feeder(ADF)State if standard or optional.5.1 ADF Type Document feed, Document fixed5.2 Document Size From _ mm x _ mmto _ mm x _ mmGive dimensions in millimeters orsta
41、ndard sizes.5.3 Document Weight (Thickness) From _ g/m2to _ g/m25.4 Capacity Total thickness _ mm max._ sheets max. (based on _g/m2)Total thickness in millimeters ornumber of sheets.The manufacturer shall indicate thenominal capacity with respect to thereference paper weight.INCITS/ISO/IEC 14473:199
42、92008 ITIC 2008 All rights reservedCopyright American National Standards Institute Provided by IHS under license with ANSI Not for ResaleNo reproduction or networking permitted without license from IHS-,-,-4Parameter Description of the entry Remark and examples5.5 Page Scanning Speed ofScanner with
43、ADF_ pages/min. (PPM)Measure the maximum number ofpages which can be scanned perminute using the ADF.State configuration: page size,orientation, scanning resolution andbits/pixel. Use 200 dpi, 1 bit/pixel,A4 and portrait if available.5.6 Dimensions of ADF Width x depth x height (mm)Specify the dimen
44、sions if the ADF isoptional.Indicate if trays, knobs or other arenot included.5.7 Weight of ADF _ kgGive weight in kilograms, if ADF isoptional.Indicate if trays are not included.6. Transparency Scanning State if standard or optional.6.1 Transparency Type State transparency film type. 35mm Negative
45、Film, 4x5Positive Film, OHF6.2 Scanning Area _ mm x _ mmGive dimensions in millimeters orstandard sizes.210 mm x 297 mm (A4), Letter,JIS B56.3 Dimensions of TransparencyUnitwidth x depth x height (mm)Give dimensions in millimeters, iftransparency unit is optional.Indicate if knobs or other are notin
46、cluded.6.4 Weight of Transparency Unit _ kgGive weight in kilograms, iftransparency unit is optional.7. Physical Characteristics andPower Source7.1 Dimensions width x depth x height (mm)Give dimensions in millimeters.Indicate if trays, knobs or other arenot included.7.2 Weight _ kg Indicate if with
47、or withoutaccessories.7.3 Voltage or Voltage Range _ Volt, _ - _ Volt. Indicate if AC or DC. Indicate if built-in battery. Indicate tolerance7.4 Frequency or FrequencyRange_ Hz, _ - _ Hz For AC power only. Indicatetolerance.7.5 Power _ Watt max.Indicate the value at the rated inputvoltage.7.6 Operat
48、ing Environment _ - _ C, _ - _ %8. EMC and Safety8.1 EMC Requirements Emission and immunity standardsapplied.CISPR 22 (Class A or B), FCC ClassA or B, VCCI-2IEC 801/1-68.2 Safety Requirements Indicate the applicable standards. IEC, UL, CSA, EN8.3 Acoustical Noise Sound power level and soundpressure levelMeasured according to ISO 7779and ISO 9295. Declared accordingto ISO 9296. Specify for basic andmaximum configuration.9. Options/Accessories9.1 Options Peripheral equipment that changesthe functionality of the machine.Feeding unitLarge capacity input trayFax adapter/board9.2 Accesso
copyright@ 2008-2019 麦多课文库（www.mydoc123.com）网站版权所有
备案/许可证编号：苏ICP备17064731号-1