ANSI INCITS ISO IEC 16448-2002 Information technology 120 mm DVD Read-only disk (Adopted by INCITS).pdf

1、 Reference numberISO/IEC 16448:2002(E)ISO/IEC 2002INTERNATIONAL STANDARD ISO/IEC16448Second edition2002-04-15Information technology 120 mm DVD Read-only disk Technologies de linformation Disque DVD de diamtre 120 mm Disque DVD lecture seule Adopted by INCITS (InterNational Committee for Information

2、Technology Standards) as an American National Standard.Date of ANSI Approval: 8/28/02Published by American National Standards Institute,25 West 43rd Street, New York, New York 10036Copyright 2002 by Information Technology Industry Council (ITI).All rights reserved.These materials are subject to copy

3、right claims of International Standardization Organization (ISO), InternationalElectrotechnical Commission (IEC), American National Standards Institute (ANSI), and Information Technology Industry Council(ITI). Not for resale. No part of this publication may be reproduced in any form, including an el

4、ectronic retrieval system, withoutthe prior written permission of ITI. All requests pertaining to this standard should be submitted to ITI, 1250 Eye Street NW,Washington, DC 20005.Printed in the United States of AmericaISO/IEC 16448:2002(E) PDF disclaimer This PDF file may contain embedded typefaces

5、. In accordance with Adobes licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this file, parties accept therein the responsibility of not infringing

6、 Adobes licensing policy. The ISO Central Secretariat accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters were optimized

7、 for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below. ISO/IEC 2002 All rights reserved. Unless otherwise specified, no

8、part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISOs member body in the country of the requester. ISO copyright office Case postal

9、e 56 CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail copyrightiso.ch Web www.iso.ch Printed in Switzerland ii ISO/IEC 2002 All rights reservedISO/IEC 16448:2002(E) ISO/IEC 2002 All rights reserved iiiContents Section 1 - General 1 1 Scope 1 2 Conformance 1 2.1 Optical Disk 1 2.

10、2 Generating system 1 2.3 Receiving system 1 3 Normative reference 1 4 Terms and definitions 1 4.1 Adhesive layer 2 4.2 Channel bit 2 4.3 Clamping Zone 2 4.4 Digital Sum Value (DSV) 2 4.5 Disk Reference Plane 2 4.6 Dual Layer disk 2 4.7 Dummy substrate 2 4.8 Entrance surface 2 4.9 Optical disk 2 4.1

11、0 Physical sector number 2 4.11 Read-only disk 2 4.12 Recorded layer 2 4.13 Reed-Solomon code 2 4.14 Reserved field 2 4.15 Sector 2 4.16 Single Layer disk 2 4.17 Spacer 2 4.18 Substrate 2 4.19 Track 3 4.20 Track pitch 3 4.21 Zone 3 5 Conventions and notations 3 5.1 Representation of numbers 3 5.2 Na

12、mes 3 6 List of acronyms 3 7 General description of the disk 4 8 General requirements 5 8.1 Environments 5 8.1.1 Test environment 5 8.1.2 Operating environment 6 8.1.3 Storage environment 6 8.1.4 Transportation 6 8.2 Safety requirements 6 8.3 Flammability 6 9 Reference measurement devices 6 9.1 Pick

13、 Up Head (PUH) 6 9.2 Measurement conditions 7 9.3 Normalized servo transfer function 8 ISO/IEC 16448:2002(E) iv ISO/IEC 2002 All rights reserved9.4 Reference Servo for axial tracking 8 9.5 Reference Servo for radial tracking 9 Section 2 - Dimensional, mechanical and physical characteristics of the d

14、isk 10 10 Dimensional characteristics 10 10.1 Overall dimensions 10 10.2 First transition area 10 10.3 Second transition area 10 10.4 Clamping Zone 10 10.5 Third transition area 11 10.6 Information Zone 11 10.6.1 Sub-divisions of the Information Zone 11 10.6.2 Track geometry 12 10.6.3 Track modes 12

15、 10.6.4 Channel bit length 12 10.7 Rim area 12 10.8 Remark on tolerances 13 10.9 Runout 13 10.9.1 Axial runout 13 10.9.2 Radial runout 13 10.10 Label 13 11 Mechanical parameters 14 11.1 Mass 14 11.2 Moment of inertia 14 11.3 Dynamic imbalance 14 11.4 Sense of rotation 14 12 Optical parameters 14 12.

16、1 Index of refraction 14 12.2 Thickness of the transparent substrate 14 12.3 Thickness of the spacer of Types C and D 14 12.4 Angular deviation 14 12.5 Birefringence of the transparent substrate 14 12.6 Reflectivity 14 Section 3 - Operational Signals 18 13 High frequency signals (HF) 18 13.1 Modulat

17、ed amplitude 18 13.2 Signal asymmetry 19 13.3 Cross-track signal 19 13.4 Quality of signals 19 13.4.1 Jitter 19 13.4.2 Random errors 19 13.4.3 Defects 19 14 Servo signals 19 14.1 Differential phase tracking error signal 19 14.2 Tangential push-pull signal 20 Section 4 - Data Format 22 15 General 22

18、16 Data Frames 22 16.1 Identification Data (ID) 22 16.2 ID Error Detection Code (IED) 23 16.3 Copyright Management Information (CPR_MAI) 24 ISO/IEC 16448:2002(E) ISO/IEC 2002 All rights reserved v16.4 Error Detection Code (EDC) 24 17 Scrambled Frames 24 18 ECC Blocks 25 19 Recording Frames 26 20 Mod

19、ulation 27 21 Physical Sectors 27 22 Suppress control of the d.c. component 29 Section 5 - Format of the Information Zone(s) 30 23 General description of an Information Zone 30 24 Layout of the Information Zone 30 25 Physical Sector numbering 30 26 Lead-in Zone 32 26.1 Initial Zone 33 26.2 Reference

20、 Code Zone 33 26.3 Buffer Zone 1 33 26.4 Buffer Zone 2 33 26.5 Control Data Zone 33 26.5.1 Physical format information 34 26.5.2 Disk manufacturing information 35 26.5.3 Content provider information 36 27 Middle Zone 36 28 Lead-out Zone 36 Annexes A (normative) - Measurement of the angular deviation

21、 37 B (normative) - Measurement of birefringence 39 C (normative) - Measurement of the differential phase tracking error 41 D (normative) - Measurement of light reflectance 45 E (normative) - Tapered cone for disk clamping 47 F (normative) - Measurement of jitter 48 G (normative) - 8-to-16 Modulatio

22、n with RLL (2,10) requirements 51 H (normative) - Burst Cutting Area (BCA) 61 J (normative) - Source Identification Code (SID) 66 K (informative) - Measurement of the thickness of the spacer of Dual Layer disks 69 L (informative) - Note on the Reference Code 71 M (informative) - Maximum transfer rat

23、e 72 N (informative) - Disk bonding 73 P (informative) - Transportation 75 ISO/IEC 16448:2002(E) vi ISO/IEC 2002 All rights reservedForeword ISO (the International Organization for Standardization) and IEC (the International Electrotechnical Commission) form the specialized system for worldwide stan

24、dardization. National bodies that are members of ISO or IEC participate in the development of International Standards through technical committees established by the respective organization to deal with particular fields of technical activity. ISO and IEC technical committees collaborate in fields o

25、f mutual interest. Other international organizations, governmental and non-governmental, in liaison with ISO and IEC, also take part in the work. In the field of information technology, ISO and IEC have established a joint technical committee, ISO/IEC JTC 1. International Standards are drafted in ac

26、cordance with the rules given in the ISO/IEC Directives, Part 3. The main task of the joint technical committee is to prepare International Standards. Draft International Standards adopted by the joint technical committee are circulated to national bodies for voting. Publication as an International

27、Standard requires approval by at least 75 % of the national bodies casting a vote. Attention is drawn to the possibility that some of the elements of this International Standard may be the subject of patent rights. ISO and IEC shall not be held responsible for identifying any or all such patent righ

28、ts. ISO/IEC 16448 was prepared by ECMA (as Standard ECMA-267) and was adopted, under a special “fast-track procedure”, by Joint Technical Committee ISO/IEC JTC 1, Information technology, in parallel with its approval of national bodies of ISO and IEC. This second edition cancels and replaces the fir

29、st edition (ISO/IEC 16448:1999), which has been technically revised. Annexes A to J form a normative part of this International Standard. Annexes K to P are for information only. INTERNATIONAL STANDARD ISO/IEC 16448:2002(E) ISO/IEC 2002 All rights reserved 1Information technology 120 mm DVD Read-onl

30、y disk Section 1 - General 1 Scope This International Standard specifies the mechanical, physical and optical characteristics of a 120 mm, read-only optical disk to enable the interchange of such disks. It specifies the quality of the recorded signals, the format of the data and the recording method

31、, thereby allowing for information interchange by means of such disks. This disk is identified as DVD - Read-Only Disk. This International Standard specifies four related but different Types of this disk (see clause 7), the conditions for conformance, the environments in which the disk is to be oper

32、ated and stored, the mechanical and physical characteristics of the disk, so as to provide mechanical interchange between data processing systems, the format of the information on the disk, including the physical disposition of the tracks and sectors, the error correcting codes and the coding method

33、 used, the characteristics of the signals recorded on the disk, enabling data processing systems to read the data from the disk. This International Standard provides for interchange of disks between disk drives. Together with a standard for volume and file structure, it provides for full data interc

34、hange between data processing systems. 2 Conformance 2.1 Optical Disk A claim of conformance shall specify the Type of the disk. An optical disk shall be in conformance with this International Standard if it meets the mandatory requirements specified for its Type. 2.2 Generating system A generating

35、system shall be in conformance with this International Standard if the optical disk it generates is in accordance with 2.1. 2.3 Receiving system A receiving system shall be in conformance with this International Standard if it is able to handle all four Types of optical disk according to 2.1. 3 Norm

36、ative reference The following normative document contains provisions which, through reference in this text, constitute provisions of this International Standard. For dated references, subsequent amendments to, or revisions of, any of these publications do not apply. However, parties to agreements ba

37、sed on this International Standard are encouraged to investigate the possibility of applying the most recent edition of the normative document indicated below. For undated references, the latest edition of the normative document referred to applies. Members of ISO and IEC maintain registers of curre

38、ntly valid International Standards. IEC 60950-1:2001, Information technology equipment Safety Part 1: General requirements 4 Terms and definitions For the purposes of this International Standard, the following terms and definitions apply. ISO/IEC 16448:2002(E) 2 ISO/IEC 2002 All rights reserved4.1 A

39、dhesive layer A layer of adhesive material bonding together the two parts of the disk. 4.2 Channel bit The elements by which, after modulation, the binary values ZERO and ONE are represented on the disk by pits. 4.3 Clamping Zone The annular part of the disk within which a clamping force is applied

40、by a clamping device. 4.4 Digital Sum Value (DSV) The arithmetic sum obtained from a bit stream by allocating the decimal value 1 to bits set to ONE and the decimal value -1 to bits set to ZERO. 4.5 Disk Reference Plane A plane defined by the perfectly flat annular surface of an ideal spindle onto w

41、hich the Clamping Zone of the disk is clamped, and which is normal to the axis of rotation. 4.6 Dual Layer disk A optical disk with one or two entrance surface(s), in which each entrance surface gives access to a different pair of recorded layers. 4.7 Dummy substrate A layer which may be transparent

42、 or not, provided for the mechanical support of the disk and/or of a recorded layer. 4.8 Entrance surface The surface of the disk onto which the optical beam first impinges. 4.9 Optical disk A disk that accepts and retains information in the form of pits in a recorded layer that can be read by an op

43、tical beam. 4.10 Physical sector number A serial number allocated to physical sectors on the disk. 4.11 Read-only disk An optical disk in which the information has been recorded when manufacturing the disk. The information cannot be modified and can only be read from the disk. 4.12 Recorded layer A

44、layer of the disk on, or in, which data is recorded. 4.13 Reed-Solomon code An error detection and/or correction code for the correction of errors. 4.14 Reserved field A field set to all ZEROs unless otherwise stated, and reserved for future standardization. 4.15 Sector The smallest part of a track

45、in the Information Zone that can be accessed independently of other addressable parts. 4.16 Single Layer disk An optical disk with one or two entrance surface(s), in which each entrance surface gives access to a different recorded layer. 4.17 Spacer In the case of Dual Layer disks, the transparent l

46、ayer placed between the two recorded layers accessible through the same entrance surface. 4.18 Substrate A transparent layer of the disk, provided for mechanical support of the recorded layer(s), through which the optical beam can access the recorded layer(s). ISO/IEC 16448:2002(E) ISO/IEC 2002 All

47、rights reserved 34.19 Track A 360 turn of a continuous spiral. 4.20 Track pitch The distance between the centrelines of a pair of adjacent physical tracks, measured in radial direction. 4.21 Zone An annular area of the disk. 5 Conventions and notations 5.1 Representation of numbers A measured value

48、is rounded off to the least significant digit of the corresponding specified value. For instance, it implies that a specified value of 1,26 with a positive tolerance of + 0,01 and a negative tolerance of - 0,02 allows a range of measured values from 1,235 to 1,275. Numbers in decimal notations are r

49、epresented by the digits 0 to 9. Numbers in hexadecimal notation are represented by the hexadecimal digits 0 to 9 and A to F in parentheses. The setting of bits is denoted by ZERO and ONE. Numbers in binary notations and bit patterns are represented by strings of digits 0 and 1, with the most significant bit shown to the left. Negative values of numbers in binary notation are given as Twos complement. In each field the data is recorded so that the most significant byte (MSB), identified as Byte 0, is recorded first and