ANSI INCITS ISO IEC 21118-2005 Information to be included in specification sheets Data projectors.pdf

1、INCITS/ISO/IEC 21118:20052008 /ISO/IEC 21118:2005, IDT) Information to be includedin specification sheets Data projectorsINCITS/ISO/IEC 21118:20052008(ISO/IEC 21118:2005, IDT)INCITS/ISO/IEC 21118:20052008 ii ITIC 2008 All rights reserved PDF disclaimer This PDF file may contain embedded typefaces. I

2、n accordance with Adobes licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this file, parties accept therein the responsibility of not infringing Ad

3、obes licensing policy. The ISO Central Secretariat accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters were optimized fo

4、r printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below. Adopted by INCITS (InterNational Committee for Information Technolog

5、y Standards) as an American National Standard. Date of ANSI Approval: 7/1/2008 Published by American National Standards Institute, 25 West 43rd Street, New York, New York 10036 Copyright 2008 by Information Technology Industry Council (ITI). All rights reserved. These materials are subject to copyri

6、ght claims of International Standardization Organization (ISO), International Electrotechnical Commission (IEC), American National Standards Institute (ANSI), and Information Technology Industry Council (ITI). Not for resale. No part of this publication may be reproduced in any form, including an el

7、ectronic retrieval system, without the prior written permission of ITI. All requests pertaining to this standard should be submitted to ITI, 1250 Eye Street NW, Washington, DC 20005. Printed in the United States of America INCITS/ISO/IEC 21118:20052008 ITIC 2008 All rights reserved iii Contents Page

8、 Foreword iv 1 Scope 1 2 Terms and definitions 1 3 Measuring methods and conditions 2 4 Items in specification sheets .2 Annex A (normative) Specification sheets .6 Annex B (informative) Measuring methods and conditions 10 Bibliography 15 INCITS/ISO/IEC 21118:20052008 iv ITIC 2008 All rights reserve

9、d Foreword ISO (the International Organization for Standardization) and IEC (the International Electrotechnical Commission) form the specialized system for worldwide standardization. National bodies that are members of ISO or IEC participate in the development of International Standards through tech

10、nical committees established by the respective organization to deal with particular fields of technical activity. ISO and IEC technical committees collaborate in fields of mutual interest. Other international organizations, governmental and non-governmental, in liaison with ISO and IEC, also take pa

11、rt in the work. In the field of information technology, ISO and IEC have established a joint technical committee, ISO/IEC JTC 1. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of the joint technical committee is to prepare Inte

12、rnational Standards. Draft International Standards adopted by the joint technical committee are circulated to national bodies for voting. Publication as an International Standard requires approval by at least 75 % of the national bodies casting a vote. Attention is drawn to the possibility that some

13、 of the elements of this document may be the subject of patent rights. ISO and IEC shall not be held responsible for identifying any or all such patent rights. ISO/IEC 21118 was prepared by Joint Technical Committee ISO/IEC JTC 1, Information technology, Subcommittee SC 28, Office equipment. AMERICA

14、N NATIONAL STANDARD INCITS/ISO/IEC 21118:20052008 ITIC 2008 All rights reserved 1 Information to be included in specification sheets Data projectors 1 Scope This International Standard is applicable for information to be included in specification sheets about front projection type, fixed resolution

15、and light valve system, and data projectors having a computer signal input port capable of projecting the image outputs from a computer, VCR or other devices. NOTE 1 It also covers Data projectors that have a video signal input port as well as a computer signal input port. NOTE 2 It is not applicabl

16、e to units with a rear projection system or with a video input terminal alone. 2 Terms and definitions For the purposes of this document, the following terms and definitions apply. 2.1 light valve a system which creates an optical image by electrical means using light from a separate source 2.2 tele

17、photo end the maximum focal length position of the zoom lens 2.3 wide-angle end the minimum focal length position of the zoom lens 2.4 resize process which converts an input image signal from one resolution and dot number to an image with a different resolution or dot number 2.5 lens shift a specifi

18、c function which enables changing the location of the image on the projection screen by moving the lens vertically (up/down) and/or horizontally (left/right) without moving the projector itself 2.6 image position(a measure of the affect of lens shift) the reference point is defined as the point on t

19、he projection screen that is intersected by the physical axis of the projection lens up image position = (Distance between top edge and reference point) down image position = (Distance between bottom edge and reference point) left image position = (Distance between left edge and reference point) rig

20、ht image position = (Distance between right edge and reference point) INCITS/ISO/IEC 21118:20052008 2 ITIC 2008 All rights reserved when image position is variable by lens shift feature, maximum and minimum positions should be specified example specification of image positions for a data projector w

21、ith lens shift: up/down 1:10 to 10:1, right /left 1:3 to 3:1 this means that the up image position with maximum lens shift upward is 10 times the up image position with no lens shift similarly the down image position with maximum lens shift downward is 10 times the down image position with no lens s

22、hift likewise, the right image position with maximum lens shift right is 3 times the right image position with no lens shift likewise, the left image position with maximum lens shift is 3 times the left image position with no lens shift note that if there is no lens shift in the horizontal direction

23、 right/left 1:1 would be the value given for right/left image position. 2.7 front projection system a projection system (of a projector) focuses an image onto a screen by projected light. The image from a light-reflecting screen is viewed from the projector side of the screen 2.8 rear projection sys

24、tem a projection system (of a projector) focuses an image onto a screen by projected light NOTE The image is viewed from the opposite side of the light transmitting screen. 3 Measuring methods and conditions Annex B (informative) shows measuring methods and conditions for the performance specificati

25、on items in Table 1. 4 Items in specification sheets Item, item specification and specification examples are shown in Table 1. They are fundamental properties, which must be included in the specification sheets. The lower-limit values of the projector must maintain 80% of the values in specification

26、 sheets for the brightness, contrast ratio and light output uniformity. The specification sheets must have a statement, which says that they are made in accordance with this standard. They must use the same number as Table 1 exactly. Items may be omitted if the projector has no function for it. When

27、 an item is omitted, numbers of the following items may not be changed. An example specification sheet is shown in Annex A (normative). NOTE When items and values are extracted from specification sheets, they can be listed in any order and their number may not be specified. INCITS/ISO/IEC 21118:2005

28、2008 ITIC 2008 All rights reserved 3 Table 1 Performance specification item No. Item Item specification Specification example 1 Product number, type name, or model number The product name, type name, model numbers, or product numbers must be entered. 2 Display system The light valve type must be ind

29、icated. a) LCD, micro mirror, other b) transmitting, reflecting c) single panel, 3 panel, other 3 Optical system The optics for colour separation and convergence must be indicated. a) Dichroic mirror separation-prism convergence system b) Time sharing separation/ convergence system c) other 4 Displa

30、y device 4.1 Size of effective display area Size, number of panels and aspect ratio must be indicated. 1,3” 3, aspect ratio 4:3 4.2 Number of pixels The numbers of pixels per sheet, numbers of sheets, and total numbers of pixels must be indicated. 480 000 pixels (800 600) 3 sheets, 1 440 000 pixels

31、in total 4.3 Other Features of display device must be indicated. without micro lens 5 Projection lens 5.1 Zoom Zoom magnifications must be indicated. Power zoom (1 to 1,4) 5.2 Focus Method of focus adjustment must be indicated. Manual, or powered 5.3 Lens shift Image position for maximum and minimum

32、 lens shift (if any) must be specified Up/down 1:10 to 10:1, right /left 1:3 to 3:1 (in case of variable lens shift in both horizontal and vertical directions) Up/down 10:1 right/left 1:1 (in case of no right/left lens shift) 5.4 Focal length (mm) Focal length and Aperture must be indicated. f = 52

33、mm 73 mm Aperture f/2,5 2,9 6 Light source The light source lamp type (name), wattage, and quantity must be indicated. Lamp number can be omitted if only one lamp is used. 300 W metal halide lamp 7 Screen size Projection distance The minimum and maximum sizes of the projected image must be indicated

34、. The associated projection distance must also be indicated. Telephoto end is for minimum size and wide-angle end for maximum size must be given for a zoom lens. Image size 0,4 m 0,3 m minimum to 2 m 1,5 m maximum for projection distance 0,8 m minimum to 4 m maximum 8 Number of colours The maximum n

35、umber of reproducible colours must be indicated. Full-colour reproduction (16 700 000 colours) 9 Light output The light output on a projected screen must be measured and indicated. Average value of production units must be indicated. 800 lm (see Annex B, B.2.2) 10 Contrast ratio (full white/full bla

36、ck) The ratio of illuminance between the white and black areas of images must be indicated. Average value of production units must be indicated. 200:1 (full white/full black) (see Annex B, B.2.3) 11 Light output uniformity The ratio between the center luminance and 4-peripheral-point average luminan

37、ce of a full-white image must be indicated. Average value of production units must be indicated. 85 % (see Annex B, B.2.4) INCITS/ISO/IEC 21118:20052008 4 ITIC 2008 All rights reserved Table 1 (continued) No. Item Item specification Specification example 12 Audio output The output power must be indi

38、cated. Either stereo or monaural must be indicated as well. 10 W + 10 W stereo (see Annex B, B.3) 13 Speaker The diameter and quantity must be indicated. 5 cm 2 14 Displayable scanning frequency 14.1 Horizontal The range of displayable horizontal frequencies must be indicated. 15 kHz to 100 kHz 14.2

39、 Vertical The range of displayable vertical frequencies must be indicated. 50 Hz to 120 Hz 15 Display resolution 15.1 For computer signal input The maximum display resolution for computer input must be indicated. Notational convention method must be indicated as well. When display resolution is beyo

40、nd the panel native resolution, it also must be indicated. The displayable video signal type (system) and resolution must be indicated. If there are two or more signal types (systems), all of them may be specified. Maximum display resolution 1024 dots 768 dots (resizing) Panel display resolution 800

41、 dots 600 dots 15.2 For video signal input If there are two or more signal types (systems), all of them may be specified. NTSC: 550 TV lines, (S-video input) PAL/SECAM: 350 TV lines (see Annex B, B.4) 16 Computer signal input/output The signal type, connector type and number of connectors must be in

42、dicated. Any order of entries and contents are acceptable. If the terminal has several functions, this may be entered as a remark. RGB input: 2 lines RGB output: 1 line RGB input port (mini-D-sub 15-pin) RGB output port (mini-D-sub 15-pin) Audio input port (RCA pin L/R) 17 Video signal input/output

43、The signal type, connector type, and number of connectors must be indicated. Any order of entries and contents are acceptable. If the terminal has several functions, this may be entered as a remark. Video/S-video input: 1 line Video input port (RCA pin) S-video port (mini-DIN 4-pin) Audio input port

44、 (RCA pin L/R) 18 Control signal input/output The control signal input/output port and other relevant descriptions must be given. Any order of entries and contents are acceptable. RS-232C and mouse input ports 19 Acoustic Noise If the noise values other than the maximum value is entered, its working

45、 condition must be indicated. Noise measurements must be made by ISO 9296 1. 35dB(A weighted) At eco mode, 30dB(A weighted) (see Annex B, B.5.2) 20 Operating temperature (operating humidity) The temperatures (relative humidity) at which the product normally operates must be indicated. The humidity n

46、eed not always be indicated. 5 C to 35 C (20 % to 70 %) 21 Power requirements The rated voltage and frequency must be indicated. AC100V, 50/60Hz 22 Power consumption The maximum power consumption must be indicated in watts. Information about standby and power-saving modes can optionally be entered.

47、380 W (see Annex B, B.6) INCITS/ISO/IEC 21118:20052008 ITIC 2008 All rights reserved 5 Table 1 (continued) No. Item Item specification Specification example 23 Outside dimensions The outside dimensions (width, height, and depth) of the product must be indicated in millimeters. The width, height, and

48、 depth may be indicated in any order. If there are any exceptions, they must be specified within parentheses. W 300 mm H 150 mm D 400 mm (without protrusions) 24 Weight The weight of the product must be indicated in kilograms. If there are any exceptions, they must be specified within parentheses. 1

49、5 kg (detachable remote controller included) 25 Accessories The names and quantities of the accessories supplied together with the product must be indicated. Remote controller, lens cap, RGB cable, mouse cable, power cable, and instruction manual 26 Other functions Features and special functions other than those indicated from 1 to 25 must be indicated. INCITS/ISO/IEC 21118:20052008 6 ITIC 2008 All rights reserved Annex A (normative) Specification sheets Annex A provides for information to b