ANSI INCITS ISO IEC 29109-2-2010 Information technology - Conformance testing methodology for biometric data interchange formats defined in ISO IEC 19794 - Part 2 Finger minutiae d.pdf

1、 INCITS/ISO/IEC 29109-2-2010 Information technology Conformance testing methodology for biometric data interchange formats defined in ISO/IEC 19794 Part 2: Finger minutiae data Reaffirmed as INCITS/ISO/IEC 29109-2:2010 R2015INCITS/ISO/IEC 29109-2-2010 PDF disclaimer This PDF file may contain embedde

2、d typefaces. In accordance with Adobes licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this file, parties accept therein the responsibility of not

3、 infringing Adobes licensing policy. The ISO Central Secretariat accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters wer

4、e optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below. Adopted by INCITS (InterNational Committee for Informa

5、tion Technology Standards) as an American National Standard. Date of ANSI Approval: 9/28/2010 Published by American National Standards Institute, 25 West 43rd Street, New York, New York 10036 Copyright 2010 by Information Technology Industry Council (ITI). All rights reserved. These materials are su

6、bject to copyright claims of International Standardization Organization (ISO), International Electrotechnical Commission (IEC), American National Standards Institute (ANSI), and Information Technology Industry Council (ITI). Not for resale. No part of this publication may be reproduced in any form,

7、including an electronic retrieval system, without the prior written permission of ITI. All requests pertaining to this standard should be submitted to ITI, 1250 Eye Street NW, Washington, DC 20005. Printed in the United States of America ii ITIC 2010 All rights reserved INCITS/ISO/IEC 29109-2-2010 I

8、TIC 2010 All rights reserved iiiContents Page Foreword iv Introduction.v 1 Scope1 2 Conformance .1 3 Normative references2 4 Terms and definitions .2 5 Symbols and abbreviated terms 2 6 Conformance testing methodology.2 6.1 General .2 6.2 Table of requirements in the base standard.2 6.3 Tables of Te

9、st Assertions.19 INCITS/ISO/IEC 29109-2-2010 iv ITIC 2010 All rights reservedForeword ISO (the International Organization for Standardization) and IEC (the International Electrotechnical Commission) form the specialized system for worldwide standardization. National bodies that are members of ISO or

10、 IEC participate in the development of International Standards through technical committees established by the respective organization to deal with particular fields of technical activity. ISO and IEC technical committees collaborate in fields of mutual interest. Other international organizations, g

11、overnmental and non-governmental, in liaison with ISO and IEC, also take part in the work. In the field of information technology, ISO and IEC have established a joint technical committee, ISO/IEC JTC 1. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives

12、, Part 2. The main task of the joint technical committee is to prepare International Standards. Draft International Standards adopted by the joint technical committee are circulated to national bodies for voting. Publication as an International Standard requires approval by at least 75 % of the nati

13、onal bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO and IEC shall not be held responsible for identifying any or all such patent rights. ISO/IEC 29109-2 was prepared by Joint Technical Committee ISO/IEC

14、 JTC 1, Information technology, Subcommittee SC 37, Biometrics. ISO/IEC 29109 consists of the following parts, under the general title Information technology Conformance testing methodology for biometric data interchange formats defined in ISO/IEC 19794: Part 1: Generalized conformance testing metho

15、dology Part 2: Finger minutiae data Part 4: Finger image data Part 5: Face image data Part 6: Iris image data Part 8: Finger pattern skeletal data Part 9: Vascular image data Part 10: Hand geometry silhouette data The following parts are under preparation: Part 3: Finger pattern spectral data Part 7

16、: Signature/sign time series data Part 11: Signature/sign processed dynamic data Part 13: Voice data Part 14: DNA data INCITS/ISO/IEC 29109-2-2010 ITIC 2010 All rights reserved vIntroduction ISO/IEC 19794-2 specifies data interchange formats for recording, storing and transmitting one or more finger

17、 minutiae records, possibly within a Common Biometric Exchange Formats Framework (CBEFF) data structure. Each minutia may be accompanied by subject-specific metadata contained in a header record. This part of ISO/IEC 29109 defines tests for checking the correctness of the binary record. The requirem

18、ents of ISO/IEC 19794-2 cannot be completely achieved until biometric products can be tested to determine whether they conform to its specifications. Conforming implementations are a necessary prerequisite for achieving interoperability among implementations; there is therefore a need for a standard

19、ized conformance testing methodology, test assertions and test procedures, as applicable to specific modalities addressed by each part of ISO/IEC 19794. The test assertions will cover as much as is practical of the ISO/IEC 19794 requirements (covering the most critical features), so that the conform

20、ity results produced by the test suites will reflect the real degree of conformity of the implementations to ISO/IEC 19794 Data Interchange Format records. This is the motivation for the development of this conformance testing methodology. This part of ISO/IEC 29109 supports those applications that

21、require use of finger minutiae data according to ISO/IEC 19794-2:2005. It defines a testing methodology to assure conformance of a vendors application or service to the base ISO/IEC 19794-2:2005 specification. Thus, it is intended to: establish elements of the Conformance Testing Met hodology framew

22、ork that are specific to the Finger Minutiae-based Data Record requirements of ISO/IEC 19794-2:2005 conformance testing, define requirements and guidelines for specifying confor mance test suites and related test methods for measuring conformity of products and services to the Finger Minutiae-based

23、Data Record requirements of ISO/IEC 19794-2:2005, and define test and reporting procedures to be followed before, during and after conformance testing. This part of ISO/IEC 29109 is applicable to the development and use of conformity test method specifications, conformity test suites for ISO/IEC 197

24、94-2:2005 records, and conformance testing programs for ISO/IEC 19794-2:2005 conformant products. It is intended primarily for use by testing organizations, but may be applied by developers and users of test method specifications and test method implementations. AMERICAN NATIONAL STANDARD INCITS/ISO

25、/IEC 29109-2-2010 ITIC 2010 All rights reserved 1Information technology Conformance testing methodology for biometric data interchange formats defined in ISO/IEC 19794 Part 2: Finger minutiae data 1 Scope This part of ISO/IEC 29109 specifies elements of conformance testing methodology, test assertio

26、ns and test procedures, as applicable to the biometric data interchange format standard relating to finger minutiae data (i.e. ISO/IEC 19794-2). It establishes tests of assertions of the structure of the finger minutiae data format as specified in ISO/IEC 19794-2:2005 (Type A Level 1 as defined in I

27、SO/IEC 29109-1:2009), tests of assertions of internal consistency by ch ecking the types of values that may be contained within each field (Type A Level 2 as defined in ISO/IEC 29109-1:2009), and tests of semantic assertions (Type A Level 3 as defined in ISO/IEC 29109-1:2009). This part of ISO/IEC 2

28、9109 does not establish tests of conformance of CBE FF structures embedding ISO/IEC 19794-2:2005 biometric data blocks (BDBs), tests of other characteristics of biometric products or other types of testing of biometric products (e.g. acceptance, performance, robustness, security), tests of conforman

29、ce of systems that do not produce ISO/IEC 19794-2:2005 records, or tests for Level 3 conformance testing. 2 Conformance Biometric data interchange format conformance tests conform to this part of ISO/IEC 29109 if they satisfy all of the normative requirements related to Clause 6. Specifically, they

30、shall use the test methodology specified in ISO/IEC 29109-1:2009, Clauses 6, 7 and 8, and all Level 1 and Level 2 tests shall use the assertions defined in Table 2. Implementations of ISO/IEC 19794-2:2005 tested according to the methodology specified shall be able to claim conformance only to those

31、Biometric Data Record (BDR) requirements specified in ISO/IEC 19794-2:2005 that are tested by the test methods established by this methodology. INCITS/ISO/IEC 29109-2-2010 2 ITIC 2010 All rights reservedImplementations of ISO/IEC 19794-2:2005 do not necessarily need to conform to all possible aspect

32、s of ISO/IEC 19794-2:2005, but only to those ISO/IEC 19794-2:2005 requirements that are claimed to be supported by the implementation in an Implementation Conformance Statement, filled out in accordance with Table 1 of this part of ISO/IEC 29109 and ISO/IEC 29109-1:2009, Clause 8. 3 Normative refere

33、nces The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO/IEC 19794-2:2005, Information technology

34、 Biometric data interchange formats Part 2: Finger minutiae data ISO/IEC 19794-2:2005/Cor.1:2009, Information technology Biometric data interchange formats Part 2: Finger minutiae data Technical corrigendum 1 ISO/IEC 29109-1:2009, Information technology Conformance testing methodology for biometric

35、data interchange formats defined in ISO/IEC 19794 Part 1: Generalized conformance testing methodology 4 Terms and definitions For the purposes of this document, the terms and definitions given in ISO/IEC 29109-1 apply. 5 Symbols and abbreviated terms For the purposes of this document, the symbols an

36、d abbreviated terms given in ISO/IEC 29109-1 apply. 6 Conformance testing methodology 6.1 General The testing methodology specified in ISO/IEC 29109-1:2009, Clauses 6, 7 and 8 shall be used. The content of the tables below is based on the conformance testing methodology outlined in 29109-1 and shall

37、 only be used in the context of that testing methodology. 6.2 Table of requirements in the base standard The normative requirements of ISO/IEC 19794-2:2005, are listed in Table 1. The supplier of the IUT can explain which optional components of the standard are supported and the testing laboratory c

38、an note the results of the test. INCITS/ISO/IEC 29109-2-2010 Table 1 Requirements of the Base Standard (19794-2:2005) Subformat Applicability Requirement Identifier Reference in Base Standard Requirement Summary Level Status1 2 3 4 5 6 25 26 27 28IUT Support Supported Range Test Result R-1 6.2 Some

39、points are neither a ridge ending nor a bifurcation. This standard therefore defines additionally a type named “other”, which shall be used in such a way that the matching conditions specified in clause 6.5 apply. The “other“ minutiae type shall not be used for minutiae that are ridge endings or rid

40、ge bifurcations. 3C O-1 Y Y Y Y Y Y Y Y Y Y N/A R-2 6.3.1 The coordinate system used to express the minutiae of a fingerprint shall be a Cartesian coordinate system. Points shall be represented by their X and Y coordinates. The origin of the coordinate system shall be the upper left corner of the or

41、iginal image with X increasing to the right and Y increasing downward. The X and Y coordinates of the minutiae shall be in pixel units, with the spatial resolution of a pixel given in the “X Resolution” and “Y Resolution” fields of the format. 3C O-1 Y Y Y Y Y Y Y Y Y Y N/A N/A R-3 6.3.2 The minutia

42、 for a ridge ending shall be defined as the point of forking of the medial skeleton of the valley area immediately in front of the ridge ending. 3C O-1 Y Y Y N Y N Y N Y N N/A N/A R-4 6.3.3 The minutia for a ridge bifurcation shall be defined as the point of forking of the medial skeleton of the rid

43、ge. If the ridges were thinned down to a single-pixel-wide skeleton, the point where the three legs intersect is the location of the minutia. 3C O-1 Y Y Y Y Y Y Y Y Y Y N/A N/A ITIC 2010 All rights reserved 3INCITS/ISO/IEC 29109-2-2010 Subformat Applicability Requirement Identifier Reference in Base

44、 Standard Requirement Summary Level Status1 2 3 4 5 6 25 26 27 28IUT Support Supported Range Test Result R-5 6.3.4 The minutia for a ridge skeleton endpoint shall be defined as the center point of the ending ridge. 3C O-1 N N N Y N Y N Y N Y N/A N/A R-6 6.3.5 For minutia other than a bifurcation or

45、ridge ending the position and angle calculations shall be done in such a way that the matching conditions in clause 6.5 apply. 3C O-1 Y Y Y Y Y Y Y Y Y Y N/A N/A R-7 6.5 Core direction: If the core has a discernible angle of direction, it shall be recorded in the core information, since this charact

46、erizes the type of core. 3C O-1 Y N N N N N N N N N N/A N/A R-8 6.5 Delta direction: For all observable divergences the angle is defined by the direction of the tangent before the pair of ridges beings to diverge. The angle shall point from divergent towards parallel ridge lines; that is, the angles

47、 shall point outwards from the delta. 3C O-1 Y N N N N N N N N N N/A N/A R-9 6.6 In a matching process, the different minutia types shall be matched according to the following Table 1. Matchers may choose to assign lower weights (or importance) to a match of type 00 to 01 or 10, than to a match of t

48、ype 00 to 00, 01 to 01, or 10 to 10. 3C O-1 Y Y Y Y Y Y Y Y Y Y N/A N/A R-10 6.7 All multibyte quantities are represented in Big-Endian format; that is, the more significant bytes of any multibyte quantity are stored at lower addresses in memory than (and are transmitted before) less significant byt

49、es. All numeric values are fixed-length integer quantities, and are unsigned quantities. 1 M Y Y Y Y Y Y Y Y Y Y N/A N/A 4 ITIC 2010 All rights reservedINCITS/ISO/IEC 29109-2-2010 Subformat Applicability Requirement Identifier Reference in Base Standard Requirement Summary Level Status1 2 3 4 5 6 25 26 27 28IUT Support Supported Range Test Result R-11 7.1 The minutiae record format sha