ANSI INCITS ISO IEC 7811-1-2002 Identification cards - Recording technique - Part 1 Embossing《识别卡.记录技术.第1部分 压纹》.pdf

1、 Reference numberISO/IEC 7811-1:2002(E)ISO/IEC 2002INTERNATIONAL STANDARD ISO/IEC7811-1Third edition2002-09-15Identification cards Recording technique Part 1: Embossing Cartes didentification Technique denregistrement Partie 1: Estampage Adopted by INCITS (InterNational Committee for Information Tec

2、hnology Standards) as an American National Standard.Date of ANSI Approval: 2/13/2003Published by American National Standards Institute,25 West 43rd Street, New York, New York 10036Copyright 2003 by Information Technology Industry Council (ITI).All rights reserved.These materials are subject to copyr

3、ight claims of International Standardization Organization (ISO), InternationalElectrotechnical Commission (IEC), American National Standards Institute (ANSI), and Information Technology Industry Council(ITI). Not for resale. No part of this publication may be reproduced in any form, including an ele

4、ctronic retrieval system, withoutthe prior written permission of ITI. All requests pertaining to this standard should be submitted to ITI, 1250 Eye Street NW,Washington, DC 20005.Printed in the United States of AmericaCopyright American National Standards Institute Provided by IHS under license with

5、 ANSINot for ResaleNo reproduction or networking permitted without license from IHS-,-,-ISO/IEC 7811-1:2002(E) PDF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobes licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces whic

6、h are embedded are licensed to and installed on the computer performing the editing. In downloading this file, parties accept therein the responsibility of not infringing Adobes licensing policy. The ISO Central Secretariat accepts no liability in this area. Adobe is a trademark of Adobe Systems Inc

7、orporated. Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event t

8、hat a problem relating to it is found, please inform the Central Secretariat at the address given below. ISO/IEC 2002 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopyi

9、ng and microfilm, without permission in writing from either ISO at the address below or ISOs member body in the country of the requester. ISO copyright office Case postale 56 CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail copyrightiso.ch Web www.iso.ch Printed in Switzerland i

10、i ISO/IEC 2002 All rights reservedCopyright American National Standards Institute Provided by IHS under license with ANSINot for ResaleNo reproduction or networking permitted without license from IHS-,-,-ISO/IEC 7811-1:2002(E) ISO/IEC 2002 All rights reserved iiiContents Page Foreword.iv 1 Scope 1 2

11、 Conformance1 3 Normative references1 4 Terms and definitions .2 5 Card characteristics 2 5.1 Card warpage .2 5.2 Surface distortions 2 5.3 Card width and height.3 6 Visually and machine readable characters.3 6.1 Character set and type font 3 6.2 Character spacing .4 6.3 Character height 4 6.4 Relie

12、f height of embossed characters.4 7 Visually readable characters 4 7.1 Character set and type font 4 7.2 Character spacing .4 7.3 Relief height of embossed characters.4 8 Assigned embossing areas 4 8.1 Identification number line.5 8.2 Name and address area 6 Annex A (normative) Pictorial representat

13、ion of numeric data7 Annex B (normative) Farrington 7B Print specifications8 Annex C (informative) Embossability20 Copyright American National Standards Institute Provided by IHS under license with ANSINot for ResaleNo reproduction or networking permitted without license from IHS-,-,-ISO/IEC 7811-1:

14、2002(E) iv ISO/IEC 2002 All rights reserved Foreword ISO (the International Organization for Standardization) and IEC (the International Electrotechnical Commission) form the specialized system for worldwide standardization. National bodies that are members of ISO or IEC participate in the developme

15、nt of International Standards through technical committees established by the respective organization to deal with particular fields of technical activity. ISO and IEC technical committees collaborate in fields of mutual interest. Other international organizations, governmental and non-governmental,

16、 in liaison with ISO and IEC, also take part in the work. In the field of information technology, ISO and IEC have established a joint technical committee, ISO/IEC JTC 1. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 3. The main task of the jo

17、int technical committee is to prepare International Standards. Draft International Standards adopted by the joint technical committee are circulated to national bodies for voting. Publication as an International Standard requires approval by at least 75 % of the national bodies casting a vote. Atten

18、tion is drawn to the possibility that some of the elements of this part of ISO/IEC 7811 may be the subject of patent rights. ISO and IEC shall not be held responsible for identifying any or all such patent rights. ISO/IEC 7811-1 was prepared by Joint Technical Committee ISO/IEC JTC 1, Information te

19、chnology, Subcommittee SC 17, Cards and personal identification. This third edition of ISO/IEC 7811-1 cancels and replaces ISO/IEC 7811-1:1995 and ISO/IEC 7811-3:1995. The user is encouraged to review the entire standard for revisions and updates. The major changes made during this revision are list

20、ed below. 1. The requirements given in ISO/IEC 7811-3:1995 are included in this edition of ISO/IEC 7811-1. 2. Special physical characteristics for embossing formerly detailed in ISO/IEC 7810:1995 have been moved to this standard. 3. Added an informative annex for a test method for embossability. ISO

21、/IEC 7811 consists of the following parts, under the general title Identification cards Recording technique: Part 1: Embossing Part 2: Magnetic stripe Low coercivity Part 6: Magnetic stripe High coercivity Annexes A and B form a normative part of this part of ISO/IEC 7811. Annex C is information onl

22、y. Copyright American National Standards Institute Provided by IHS under license with ANSINot for ResaleNo reproduction or networking permitted without license from IHS-,-,-11 ScopeThis part of ISO/IEC 7811 is one of a series of standards describing the parameters for identification cards asdefined

23、in the definitions clause and the use of such cards for international interchange.This part of ISO/IEC 7811 specifies requirements for embossed characters on identification cards. The embossedcharacters are intended for transfer of data either by use of imprinters or by visual or machine reading. It

24、 takes intoconsideration both human and machine aspects and states minimum requirements.It is the purpose of this series of standards to provide criteria to which cards shall perform. No consideration isgiven within these standards to the amount of use, if any, experienced by the card prior to test.

25、 Failure to conformto specified criteria should be negotiated between the involved parties.ISO/IEC 10373-1 specifies the test procedures used to check cards against the parameters specified in thispart of ISO/IEC 7811.NOTE Numeric values in the SI and/or Imperial measurement system in this part of I

26、SO/IEC 7811 may have beenrounded off and therefore are consistent with, but not exactly equal to, each other. Either system may be used, but the twoshould not be intermixed or reconverted. The original design was made using the Imperial measurement system.2 ConformanceA prerequisite for conformance

27、with this part of ISO/IEC 7811 is conformance with ISO/IEC 7810 for the ID-1 sizecard. An identification card is in conformance with this part of ISO/IEC 7811 if it meets all mandatory requirementsspecified herein. Default values apply if no others are specified.3 Normative referencesThe following n

28、ormative documents contain provisions which, through reference in this text, constitute provisions ofthis part of ISO/IEC 7811. For dated references, subsequent amendments to, or revisions of, any of thesepublications do not apply. However, parties to agreements based on this part of ISO/IEC 7811 ar

29、e encouraged toinvestigate the possibility of applying the most recent editions of the normative documents indicated below. Forundated references, the latest edition of the normative document referred to applies. Members of ISO and IECmaintain registers of currently valid International StandardsISO

30、1073-1, Alphanumeric character sets for optical recognition Part 1: Character set OCR-A Shapes anddimensions of the printed imageISO 1073-2, Alphanumeric character sets for optical recognition Part 2: Character set OCR-B Shapes anddimensions of the printed imageISO 1831, Printing specifications for

31、optical character recognitionISO/IEC 7810, Identification cards Physical characteristicsISO/IEC 7812-1, Identification cards Identification of issuers Part 1: Numbering systemINTERNATIONAL STANDARD ISO/IEC 7811-1:2002(E)Identification cards Recording technique Part 1: Embossing ISO/IEC 2002 All righ

32、ts reserved Copyright American National Standards Institute Provided by IHS under license with ANSINot for ResaleNo reproduction or networking permitted without license from IHS-,-,-2ISO/IEC 7812-2, Identification cards Identification of issuers Part 2: Application and registration proceduresISO/IEC

33、 10373-1, Identification cards Test methods Part 1: General characteristics tests4 Terms and definitionsFor the purposes of this part of ISO/IEC 7811, the definition of “identification card” given in ISO/IEC 7810 and thefollowing terms and definitions apply.4.1embossingto raise characters in relief

34、from the front surface of the card4.2unused cardcard which has been embossed with all the characters required for its intended purpose but has not been issued4.3returned cardembossed card after it has been issued to the card holder and returned for the purpose of testing4.4identification numbernumbe

35、r that identifies the card holder5 Card characteristicsSpecial attention shall be paid to the characteristics of the material affecting its suitability for this purpose,particularly in respect to its ability to resist crushing and collapsing of the embossed parts when operating inimprinters.Cards sh

36、all be made of PVC (polyvinyl chloride) and/or PVCA (polyvinyl chloride acetate) or materials having equalor better performance such as polyesters, polyethylenes and polycarbonates.NOTE Refer to machine manufacturer instructions regarding card construction requirements for achieving embossedcharacte

37、r relief heights in compliance with this part of ISO/IEC 7811. At the time of publication there was no agreed testmethod for verifying the suitability of card structures for embossing. See Informative Annex C.5.1 Card warpageWhen lying convex side up on a flat rigid surface, the maximum distance fro

38、m the flat surface to any non-embossedportion of the convex side of an embossed card immediately prior to issue shall not be greater than 2,5 mm(0.10 in) including the card thickness.NOTE The amount of card warpage depends on the card material and the embossing technique used.5.2 Surface distortions

39、No raised area shall exceed 0,51 mm (0.020 in) on the front of the card in the area A as shown in Figure 1.ISO/IEC 7811-1:2002(E) ISO/IEC 2002 All rights reserved Copyright American National Standards Institute Provided by IHS under license with ANSINot for ResaleNo reproduction or networking permit

40、ted without license from IHS-,-,-3widthheight2,54(0.100)dimensions in millimetres (inches)24,03(0.946)AreaAfront of cardtop reference edgeWidth Heightmaximum minimum maximum minimum85,90 (3.382) 85,47 (3.365) 54,18 (2.133) 53,92 (2.123)Figure 1 Embossed card dimensions5.3 Card width and heightAll po

41、ints on the edges of the embossed card in the finished state, except for the rounded corners, shall fallbetween two concentric, similarly aligned rectangles as defined in Figure 1 for maximum height and width, andminimum height and width.NOTE 1 Card width and height tolerances given here are differe

42、nt than those in ISO/IEC 7810 to account for changes in cardsize due to embossing.NOTE 2 All identification card standards use the top edge of the card as the reference edge for dimensions, except for thisembossing standard which, for historical reasons, uses the bottom edge of the card as the refer

43、ence.6 Visually and machine readable characters6.1 Character set and type fontThe numeric characters of one of the following type fonts shall be used for embossed characters intended for visualand/or machine reading, either directly from the card or from card imprints (see annex A): ISO 1073-1, OCR-

44、A, Sizes I and IV; ISO 1073-2, OCR-B, Sizes I and IV; Type font Farrington 7B as described in Annex B.NOTE To ensure system compatibility in the choice of font, the attention of intending users is drawn to the necessity ofagreement with their potential interchange partners. ISO/IEC 2002 All rights r

45、eserved ISO/IEC 7811-1:2002(E) Copyright American National Standards Institute Provided by IHS under license with ANSINot for ResaleNo reproduction or networking permitted without license from IHS-,-,-4Print specifications are given in ISO 1831.6.2 Character spacingThe centreline to centreline chara

46、cter spacing shall be 3,63 mm 0,15 mm (0.143 in 0.006 in).6.3 Character heightMaximum height at the printing surface of the embossed characters, encompassing centreline skew and charactermisalignment shall be 4,32 mm (0.170 in).6.4 Relief height of embossed charactersRelief height of imprinting char

47、acter surfaces above the card surface as measured from the non-embossed surfaceof the card to the highest point on the embossed character is shown in Table 1 for unused cards and for returnedcards.7 Visually readable characters7.1 Character set and type fontA type font such as the alphanumeric, uppe

48、r case characters described in ISO 1073-2, OCR-B, Size I, shouldbe used for embossed characters intended for visually reading directly from the card or from card imprints.7.2 Character spacingThe centreline to centreline character spacing shall be 2,54 mm 0,15 mm (0.100 in 0.006 in).7.3 Relief heigh

49、t of embossed charactersRelief height of imprinting character surfaces above the card surface as measured from the non-embossed surfaceof the card to the highest point on the embossed character is shown in Table 1 for unused cards and for returnedcards.Table 1 Relief height of embossed charactersDimensions in millimetres (inches)Visually and machine reada