ANSI ISA 75.08.09-2016 Face-to-Face Dimensions for Sliding Stem Flangeless Control Valves (Classes 150 300 and 600).pdf

1、 AMERICAN NATIONAL STANDARD ANSI/ISA-75.08.09-2016 Face-to-Face Dimensions for Sliding Stem Flangeless Control Valves (Classes 150, 300, and 600) Approved 11 March 2016 ANSI/ISA-75.08.09-2016 Face-to-Face Dimensions for Sliding Stem Flangeless Control Valves (Classes 150, 300, and 600) ISBN: 978-1-9

2、41546-88-8 Copyright 2016 by the International Society of Automation. All rights reserved. Not for resale. Printed in the United States of America. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means (electronic mechanical, photocop

3、ying, recording, or otherwise), without the prior written permission of the Publisher. ISA 67 Alexander Drive P.O. Box 12277 Research Triangle Park, North Carolina 27709 - 3 - ANSI/ISA-75.08.09-2016 Copyright 2016 ISA. All rights reserved. Preface This preface, as well as all footnotes and annexes,

4、is included for information purposes and is not part of ANSI/ISA-75.08.09-2016. The standards referenced within this document may contain provisions which, through reference in this text, constitute requirements of this document. At the time of publication, the editions indicated were valid. All sta

5、ndards are subject to revision, and parties to agreements based on this document are encouraged to investigate the possibility of applying the most recent editions of the standards indicated within this document. Members of IEC and ISO maintain registers of currently valid International Standards. A

6、NSI maintains registers of currently valid U.S. National Standards. This document has been prepared as part of the service of the International Society of Automation (ISA), toward a goal of uniformity in the field of instrumentation. To be of real value, this document should not be static but should

7、 be subject to periodic review. Toward this end, the Society welcomes all comments and criticisms and asks that they be addressed to the Secretary, Standards and Practices Board; ISA; 67 Alexander Drive; P. O. Box 12277; Research Triangle Park, NC 27709; Telephone (919) 549-8411; Fax (919) 549-8288;

8、 E-mail: standardsisa.org. The ISA Standards and Practices Department is aware of the growing need for attention to the metric system of units in general, and the International System of Units (SI) in particular, in the preparation of instrumentation standards. The Department is further aware of the

9、 benefits to USA users of ISA standards of incorporating suitable references to the SI (and the metric system) in their business and professional dealings with other countries. Toward this end, this Department will endeavor to introduce SI-acceptable metric units in all new and revised standards, re

10、commended practices, and technical reports to the greatest extent possible. Standard for Use of the International System of Units (SI): The Modern Metric System, published by the American Society for Testing it is a dimension for only the valve itself. 11 ANSI/ISA-75.08.09-2016 Copyright 2016 ISA. A

11、ll rights reserved. Annex A Dimensions for metrically sized valves This annex is not part of ANSI/ISA-75.08.09-2016, but it is included to facilitate its use. Face-to-face dimensions to start this standard were obtained from Scientific Apparatus Makers Association (SAMA), Proposed Standard PMC 23.3e

12、-1975, “Face-to-Face Dimensions of Flangeless Control Valves.” Dimensions for metrically sized valves are nominal conversions that are conventionally used in the Manufacturers Standardization Society (MSS) of the Valve and Fitting Industry (MSS-SP86-1997), International Standards Organization (ISO),

13、 and International Electrotechnical Commission (IEC). This page intentionally left blank. Developing and promulgating sound consensus standards, recommended practices, and technical reports is one of ISAs primary goals. To achieve this goal the Standards and Practices Department relies on the techni

14、cal expertise and efforts of volunteer committee members, chairmen and reviewers. ISA is an American National Standards Institute (ANSI) accredited organization. ISA administers United States Technical Advisory Groups (USTAGs) and provides secretariat support for International Electrotechnical Commi

15、ssion (IEC) and International Organization for Standardization (ISO) committees that develop process measurement and control standards. To obtain additional information on the Societys standards program, please write: ISA Attn: Standards Department 67 Alexander Drive P.O. Box 12277 Research Triangle Park, NC 27709 ISBN: 978-1-941546-88-8