ANSI NEMA C78.1406-2004 Electric Lamps - P28 Single-Contact Medium Prefocus-Based Projection Lamps for Base-Down Operation - Dimensions.pdf

1、NEMA Standards PublicationNational Electrical Manufacturers AssociationANSI C78.1406-2004 (R2015)Electric Lamps P28 Single-Contact Medium Prefocus-Based Projection Lamps for Base-Down Operation DimensionsC78.1406-2004 (R2008, R2015) American National Standard for Electric Lamps P28 Single-Contact Me

2、dium Prefocus-Based Projection Lamps for Base-Down Operation Dimensions Secretariat: National Electrical Manufacturers Association Approved: July 24, 2015 American National Standards Institute, Inc. 2015 National Electrical Manufacturers Association NOTICE AND DISCLAIMER The information in this publ

3、ication was considered technically sound by the consensus of persons engaged in the development and approval of the document at the time it was developed. Consensus does not necessarily mean that there is unanimous agreement among every person participating in the development of this document. ANSI

4、standards and guideline publications, of which the document contained herein is one, are developed through a voluntary consensus standards development process. This process brings together volunteers and/or seeks out the views of persons who have an interest in the topic covered by this publication.

5、 While NEMA administers the process to promote fairness in the development of consensus, it does not write the document and it does not independently test, evaluate, or verify the accuracy or completeness of any information or the soundness of any judgments contained in its standards and guideline p

6、ublications. NEMA disclaims liability for any personal injury, property, or other damages of any nature whatsoever, whether special, indirect, consequential, or compensatory, directly or indirectly resulting from the publication, use of, application, or reliance on this document. NEMA disclaims and

7、makes no guaranty or warranty, expressed or implied, as to the accuracy or completeness of any information published herein, and disclaims and makes no warranty that the information in this document will fulfill any of your particular purposes or needs. NEMA does not undertake to guarantee the perfo

8、rmance of any individual manufacturer or sellers products or services by virtue of this standard or guide. In publishing and making this document available, NEMA is not undertaking to render professional or other services for or on behalf of any person or entity, nor is NEMA undertaking to perform a

9、ny duty owed by any person or entity to someone else. Anyone using this document should rely on his or her own independent judgment or, as appropriate, seek the advice of a competent professional in determining the exercise of reasonable care in any given circumstances. Information and other standar

10、ds on the topic covered by this publication may be available from other sources, which the user may wish to consult for additional views or information not covered by this publication. NEMA has no power, nor does it undertake to police or enforce compliance with the contents of this document. NEMA d

11、oes not certify, test, or inspect products, designs, or installations for safety or health purposes. Any certification or other statement of compliance with any health- or safety-related information in this document shall not be attributable to NEMA and is solely the responsibility of the certifier

12、or maker of the statement. ANSI C78.1406-2004 (R2008, R2015) Page i 2015 National Electrical Manufacturers Association AMERICAN NATIONAL STANDARD Approval of an American National Standard requires verification by The American National Standards Institute, Inc. (ANSI) that the requirements for due pr

13、ocess, consensus, and other criteria for approval have been met by the standards developer. An American National Standard implies a consensus of those substantially concerned with its scope and provisions. Consensus is established when, in the judgment of the ANSI Board of Standards Review, substant

14、ial agreement has been reached by directly, and materially affected interests. Substantial agreement means much more than a simple majority, but not necessarily unanimity. Consensus requires that all views and objections be considered, and that a concerted effort be made toward their resolution. The

15、 existence of an American National Standard does not in any respect preclude anyone, whether s/he has approved the standard or not, from manufacturing, marketing, purchasing, or using products, processes, or procedures not conforming to the standards. It is intended as a guide to aid the manufacture

16、r, the consumer, and the general public. The American National Standards Institute, Inc., does not develop standards and will in no circumstances give an interpretation of any American National Standard. Moreover, no person shall have the right or authority to issue an interpretation of an American

17、National Standard in the name of the American National Standards Institute, Inc. Requests for interpretations should be addressed to the secretariat or sponsor whose name appears on this title page. CAUTION NOTICE: This American National Standard may be revised or withdrawn at any time. The procedur

18、es of the American National Standards Institute, Inc., require that action be taken periodically to reaffirm, revise, or withdraw this standard. Purchasers of American National Standards may receive current information on all standards by calling or writing the American National Standards Institute,

19、 Inc. Published by National Electrical Manufacturers Association 1300 North 17th Street, Suite 900 Rosslyn, Virginia 22209 2015 National Electrical Manufacturers Association All rights, including translation into other languages, reserved under the Universal Copyright Convention, the Berne Conventio

20、n for the Protection of Literary and Artistic Works, and the International and Pan American copyright conventions. No part of this publication may be reproduced in any form, in an electronic retrieval system or otherwise, without prior written permission of the publisher. Printed in the United State

21、s of America ANSI C78.1406-2004 (R2008, R2015) Page ii 2015 National Electrical Manufacturers Association Foreword (This foreword is not part of American National Standard C78.1406-2004.) Suggestions for improvement of this standard should be submitted to Secretariat C78 National Electrical Manufact

22、urers Association 1300 North 17th Street, Suite 900 Rosslyn, Virginia 22209 This standard was processed and approved by Accredited Standards Committee on Electric Lamps, C78. Committee approval of the standard does not necessarily imply that all committee members voted for that approval. ANSI C78.14

23、06-2004 (R2008, R2015) Page iii 2015 National Electrical Manufacturers Association Contents Foreword ii 1. Scope . 1 2. Normative References 1 3. Dimensions . 1 4. Operating Position 1 Appendix . 3 Figures Figure 1 Dimensions for Single-Contact Medium Prefocus Base-Down Type Projection Lamps 2 ANSI

24、C78.1406-2004 (R2008, R2015) Page iv 2015 National Electrical Manufacturers Association ANSI C78.1406-2004 (R2008, R2015) Page 1 2015 National Electrical Manufacturers Association 1. Scope 1.1 This standard establishes the dimensions essential to interchangeability of single-contact medium prefocus

25、based projection lamps of T-10 and T-12 bulb sizes. It is not the intent to prescribe operating characteristics or details of design. 2. Normative References 2.1 The following standards contain provisions which, through reference in this text, constitute provisions of this American National Standard

26、. At the time of publication, the editions indicated were valid. All standards are subject to revision, and parties to agreements based on this American National Standard are encouraged to investigate the possibility of applying the most recent editions of the standards indicated below. ANSI C78.370

27、-1997, Method for the designation of photo lamps ANSI C79.1-2002, Nomenclature for Glass Bulbs Intended for Use with Electric Lamps ANSI C81.61-2003, Specifications for Bases (Caps) for Electric Lamps 2.2 Lamp Code Designations: Incandescent projection lamps are usually identified by a three-letter

28、code, as specified in American National Standard Method for the Designation of Photo Lamps, ANSI C78.370. 3. Dimensions 3.1 The dimensions and characteristics of the lamp base, IEC base designation P28s, shall comply with American National Standard Specifications for Electric Lamp Bases ANSI C81.61.

29、 3.2 The dimensions shall be as specified in Figure 1 and its accompanying table. The plane of the filament bisects the base flanges within 5. The filament shall be centered on base axis within 0.030 in (0.76mm) in both front and side views. 4. Operating Position 4.1 Lamps of this type are intended

30、to be burned with the axis in an essentially vertical position with the base at the bottom. ANSI C78.1406-2004 (R2008, R2015) Page 2 2015 National Electrical Manufacturers Association Inches Millimeters Dimensions* T-10 T-12 T-10 T-12 A B C (Note 1) D (Note 2) E (Note 1) F G H 1.294 max 4.797 max 0.

31、725 max 3.485 min 0.668 max 2.187 0.030 1.323 nom 5.750 max 1.546 max 4.797 max 0.850 max 3.485 max 0.785 max 2.187 0.030 1.323 nom 5.750 max 32.87 max 121.84 max 18.42 max 88.52 min 16.97 max 55.55 0.76 33.60 nom 146.05 max 39.27 max 121.84 max 21.59 max 88.52 min 19.94 max 55.55 0.76 33.60 nom 146

32、.05 max * Angular dimensions are nominal. NOTES 1 Dimensions C and E define the maximum excursion of the bulb surfaces from the base axis toward the condensing lenses (Dimension E) and the mirror (Dimension C). Therefore, the lamp chimney, the mirror, and the condensing lenses, and their respective

33、mounts, must be so located as to ensure adequate clearance between these parts and the bulb surface. 2 Dimension D applies to those projection lamps having opaque end coatings. However, there are exceptions, the specifications of which are supplied by the equipment manufacturer. Figure 1 Dimensions

34、for Single-Contact Medium Prefocus Base-Down Type Projection Lamps ANSI C78.1406-2004 (R2008, R2015) Page 3 2015 National Electrical Manufacturers Association Appendix (This Appendix is not a part of American National Standard Dimension C78.1406-2004, but is included for information only.) A1 The lo

35、cation of the lamp in a holder is determined by the winged flanges on the base shell. The top surface of the flanges determines the vertical location, the diameter of the flanges determines the lateral location, and the leading edge of the large angular flange section determines the rotational align

36、ment. A2 The terms “T-10” and “T-12” define the general shape and nominal diameter of the bulb. The letter “T” is an abbreviation for tubular; the numbers relate to the nominal diameter in eights of an inch; for example, T-10 is a tubular bulb 10/8 or 1-1/4 inches in diameter. See American National

37、Standard Nomenclature for Glass Bulbs Intended for Use with Electric Lamps, ANSI C79.1. NATIONAL ELECTRICAL MANUFACTURERS ASSOCIATION 1300 NORTH 17TH STREET, SUITE 900 ROSSLYN. VA 22209www.NEMA.orgTO ORDER ADDITIONAL NEMA STANDARDS VISITWWW.GLOBAL.IHS.COM OR CALL 1-800-854-7179/1-303-397-79565612_0514TB