ANSI NEMA C78.22-1995 Incandescent Lamps - A G PS and Similar Shapes with E39 Mogul Screw Bases (Revision of ANSI C78.22-1989).pdf

1、NEMA Standards PublicationNational Electrical Manufacturers AssociationANSI C78.22-1995 (R2003)Incandescent LampsA, G, PS, and SimilarShapes with E39 MogulScrew BasesNOTICE AND DISCLAIMER The information in this publication was considered technically sound by the consensus of persons engaged in the

2、development and approval of the document at the time it was developed. Consensus does not necessarily mean that there is unanimous agreement among every person participating in the development of this document. The National Electrical Manufacturers Association (NEMA) standards and guideline publicat

3、ions, of which the document contained herein is one, are developed through a voluntary consensus standards development process. This process brings together volunteers and/or seeks out the views of persons who have an interest in the topic covered by this publication. While NEMA administers the proc

4、ess and establishes rules to promote fairness in the development of consensus, it does not write the document and it does not independently test, evaluate, or verify the accuracy or completeness of any information or the soundness of any judgments contained in its standards and guideline publication

5、s. NEMA disclaims liability for any personal injury, property, or other damages of any nature whatsoever, whether special, indirect, consequential, or compensatory, directly or indirectly resulting from the publication, use of, application, or reliance on this document. NEMA disclaims and makes no g

6、uaranty or warranty, expressed or implied, as to the accuracy or completeness of any information published herein, and disclaims and makes no warranty that the information in this document will fulfill any of your particular purposes or needs. NEMA does not undertake to guarantee the performance of

7、any individual manufacturer or sellers products or services by virtue of this standard or guide. In publishing and making this document available, NEMA is not undertaking to render professional or other services for or on behalf of any person or entity, nor is NEMA undertaking to perform any duty ow

8、ed by any person or entity to someone else. Anyone using this document should rely on his or her own independent judgment or, as appropriate, seek the advice of a competent professional in determining the exercise of reasonable care in any given circumstances. Information and other standards on the

9、topic covered by this publication may be available from other sources, which the user may wish to consult for additional views or information not covered by this publication. NEMA has no power, nor does it undertake to police or enforce compliance with the contents of this document. NEMA does not ce

10、rtify, test, or inspect products, designs, or installations for safety or health purposes. Any certification or other statement of compliance with any health or safety-related information in this document shall not be attributable to NEMA and is solely the responsibility of the certifier or maker of

11、 the statement. NEMA C78.22 95 I 6470247 0507222 794 Approval of an American National Standard requires verification by ANSI that the requirements for due process, consensus, and other criteria for aDDroval have been met by the standards develowr. American National Consensus is established when, in

12、the judgment of the ANSI Board of Standards Review, substantial agreement has been reached by directly and materially affected interests. Substantial agreement means much more than a simple majorii, but not necessarily unanimity. Consensus requires that all views and objections be considered, and th

13、at a concerted effort be made toward their resolution. Standard The use of American National Standards is completely voluntary; their existence does not in any respect preclude anyone, whether he has approved the standards or not, from manufacturing, marketing, purchasing, or using products, process

14、es, or procedures not conforming to the standards. The American National Standards Institute does not develop standards and will in no circumstances give an interpretation of any American National Standard. Moreover, no person shall have the right or authority to issue an interpretation of an Americ

15、an National Standard in the name of the American National Standards Institute. Requests for interpretations should be addressed to the secretariat or sponsor whose name appears on the title page of this standard. CAUTION NOTICE: This American National Standard may be revised or withdrawn at any time

16、. The procedures of the Ametican National Standards Institute require that action be taken periodically to reaffirm, revise, or withdraw this standard. Purchasers of Amerimn National Standards may receive current information on all standards by calling or wriiing the American National Standards Inst

17、itute. Published by National Electrical Manufacturers Association 1300 North 17th Street, Suite 1847, Rosslyn, VA 22209 Copyright O 1996 National Electrical Manufacturers Association All rights reserved. No part of this publication may be reproduced in any form, in an electronic rer-wal system or ot

18、herwise, without prior written permicsion of the publisher. Printed in the United States of America CONTENTS Page Foreword . i Part I - General Information . 1 Part II - Lamp Classes 7 Table 1 9 Table 2 1 O Part III - Lamp Space Drawings . 11 Part IV -Annexes 17 Annex A . 19 Annex B i NENA C78.22 95

19、 m 6470247 0507224 567 Foreword (This Foreword is not pari of American National Standard C7.22-1995) This American National Standard, Incandescent Lamps - A, GI PS, and Similar Shapes with E39 Mogul Screw Bases, C78.22-1995 sets forth the physical and electrical characteristics of the grwp of incand

20、escent lamps that have A, G, PS, and similar bulb shapes with E39 Mogul screw (single- or doublecontact) bases. Suggestions for improvement of this standard will be welcome. They should be sent to the Secretary of Committee C78. National Electrical Manufacturers Association, 1300 North 17th Street,

21、Suite 1847, Rosslyn, VA 22209. This standard was processed and approved for submittal to ANSI by C78 Accredited Standards Committee on Electric Lamps, and C78-1, Incandescent Lamps. Committee approval of the standard does not necessarily imply that all committee members voted for its approval. The m

22、embers of the Committees at the time of publishing are: AI Rousseau, C78, Chairman Randolph N. Roy, Secretariat AI Rousseau, Technical Coordinator Jeanne L. Spicer, Editorial Coordinator Organization Represented Name of Representative Advance Transformer Company Duro-Test Corporation Edison Electric

23、 Institute (Delegate) Inchcape ETL Testing Laboratory General Electric Lighting Illuminating Engineering Society National Electrical Manufacturers Association (Delegate) OSRAM SYLVANIA INC Philips Lighting Company Underwriters Laboratories William A. Murray, C78-1, Chairman Randolph N. Roy, Secretar

24、iat Duro-Test Corporation General Electric Lighting Indy Lighting, Inc. OSRAM SYLVANIA INC. Philips LigMing Company Underwriiers Laboratories, Inc. Norman Grimchaw Herbert Strauss William Maguire Craig Davenport Ralph Kaiser Rita Harrold Richard Snow Peter Bleasby Aifred Rousseau David BeQ Michael J

25、. Santelli Charles W. Cox John P. Krissinger Ted Yahraus David Fox Richard Fleegal William A. Murray Ed Hinde Steven Sirek David M. Bett Kevin P. Kanakos ii NEMA C78-22 95 m b470247 0507225 4T3 m ANSI C78.22-1995 Part I General Information 1 ANSI C78.22-1995 2 NEVA C78.22 95 6470247 0507227 276 AMER

26、ICAN NATIONAL STANDARD ANSI C78.22-1995 American National Standard for Electric Lamps - Incandescent Lamps - A, Gy PS, and Similar Shapes with E39 Mogul Screw Bases 1 Scope This standard sets forth the physical and electrical characteristics of the group of incandescent lamps that have A, G, PS, and

27、 similar bulb shapes with E39 mogul screw (single- or double-wntact) bases. Only clear, inside frost, and white bulb finishes are acknowledged. Excluded from coverage are tungsten- halogen lamps and projection lamps. In addition to common-line voitage lamps, listed in Table 1 , a group of series bur

28、ning lamps rated at constant current are covered in Table 2. Other groups of incandescent lamps are covered in the following related standards: ANSI C78.20-1995, American National Standard for Electric Lamps - Incandescent Lamps - A, G, PS, and Similar Shapes with E26 Medium Screw Bases ANSI C78.21-

29、1995, American National Standard for Electric Lamps - Incandescent Lamps - PAR and R Shapes ANSI C78.23-1995, American National Standard for Electric Lamps - Incandescent Lamps - Miscellaneous Types At the time of issuance of this standard, there was no comparable standard published by the Internati

30、onal Electrotechnical Commission (IEC). 2 Normative references The following standards contain provisions which, through reference in this text, constitute provisions of this American National Standard. At the time of publication, the editions indicated were valid. All standards are subject to revis

31、ion, and parties to agreements based on this American National Standard are encouraged to investigate the possibility of applying the most recent editions of the standards indicated below. ANSI C78.25-1991, Electric lamps -Method of Measuring Lamp-Base Temperature Rise ANSI C79.1-1980 (R1994), Nomen

32、clature for Glass Bulbs Intended for Use with Electric Lamps ANSI C81.61-1990, American National Standard for Electrical Lamp Bases ANSI C81.63-1991 , American National Standard for Lamp Bases and Lamp Holders Gauges IES LM45, IES Approved Method for Electrical and Photometric Measurements of Genera

33、l Service Incandescent filament Lamps IES LM54, IES Guide to Lam Seasoning SR 30a. Procedure for Use in Preparation of Lamp Space Drawing& Available hom the Illuminating Engineering Society, 120 Wall Street - 17th Floor, New York, NY 1ooo54001. Available from the Ci8 Secretariat, do National Electri

34、cal Manufacturers Association, 1300 North 17th Street, Suite 1847, Rosslyn, VA 22209. 2 3 NENA C78.22 95 6470247 0507228 I102 ANSI C78.22-1995 3 Definitions and abbreviations In addition to bulb and base codes that are defined in the standards listed in Section 2, some terms common to the industry a

35、re utilized in this standard. 3.1 the top of the bulb. MOL (Maximum Overall Length): The distance along the lamps axis from the eyelet solder to 3.2 bases) to the center of the light-emitting area of the lamp. LCL (Light Center Length): The distance from the reference plane (eyelet solder for screw

36、3.3 finish, and filament type: including two or more voitage ratings within a voltage range. Class: A grouping of like lamps having the same rated wattage, bulb shape, base, MOL, bulb NOTE-Each line itern in Tables 1 and 2 is a dass. 3.4 Voltage range: A series of rated voltages related to commonly

37、available supply lines. NOTE-A foob-ote to Tables 1 and 2 lists several common voitage ranges appiying to ciassas of hmpc in this standard. 3.5 Rated wattage: The wattage marked on the lamp. 3.6 Rated voitage: The voltage matked on the lamp or declared by the manufacturer. NOTE-lf lamps are marked w

38、ith a range volage. it shall be interpreted that they are appropriate for uce on any line voltage within that range. Consult manufacture& catalog to determine design voltage. 3.7 Rated lumens: The lumen value marked on the lamp or declared by the manufacturer. 3.8 Rated current: The current value ma

39、rked on the lamp, if necessary. 3.9 Base temperature rise: The surface temperature rise (above ambient) of a standard test lampholder fitted to the lamp, when measured in accordance with the standard method. See Section 8 for methods of measurement. 3.10 this standard, is not necessarily the only ap

40、plication. Service: The field of most common application for a given lighting source. Service, as used in 4 Lamp designations This standard does not place any control over lamp designations. Incandescent lamps are generally designated by wattage and voltage ratings. Additional codes may be applied b

41、y the lamp manufacturer. See the lamp manufacturers catalog for detailed information. 5 Bulb designations Bulb designations used in this standard are defined in ANSI C79.1. Since the traditional eighth-inch sizes have long been utilized in some lamp designations, they are used in this standard. Thei

42、r metric versions are shown in parentheses. he is no attempt to identify or dassify filament type in this standard. 4 NEMA C78.22 95 6470247 0507229 049 ANSI C78.22-1995 6 Bulb finish Only lamps with clear, inside frost, or translucent white bulb finishes are considered in this standard. Silver bowl

43、, enamel, transparent, and other special coatings are not covered. 7 Lamp space drawings For each bulb- base- MOL category, the lamp space drawings in Part III of this standard show the maximum limits of the space that may be occupied by any part of the bulb. A typical bulb shape is shown, as a dash

44、ed line, within that maximum space. The space shown shall accommodate the longest and shortest lamps with maximum bowl and neck diameters, and maximum bulb eccentricity. These drawings were prepared in accordance with SR30a. The following general conditions apply to the construction of these space d

45、rawings: Straight lines are used as much as possible to simplify the space outlines. All compromises with the actual space are in excess of the actual space required. All excursions of a lamp bulb are shown relative to a fixed position base. Bulb eccentricity with respect to the base axis is a combi

46、nation of allowances for angular tilt (skewness) and lateral displacement (true eccentricity). An eccentricity angle of 3“ applies generally to incandescent lamps, unless special applications require tighter limits. The base contact-making gauge for each type of base controls the space near the rim

47、of the base in the base-to-neck transition zone. All dimensions are in millimeters unless otherwise specified. The figure numbers shown in Tables 1 and 2 under the column “Lamp Space Drawing“ relate directly to the former American National Standard for that category. For instance, Figure C78.22-214

48、was derived from the former standard ANSI C78.214-1949. 8 Methods of measurement 8.1 8.2 9 Electrical characteristics The values of lamp voltage, current, and wattage shown in Part II are those nominal values that apply after the lamps have been seasoned. (See IES LM54 for guidelines on lamp seasoni

49、ng.) 1 O Requirements 10.1 and special gauges, shall comply with C81.61 and ANSI C81.63. 10.2 in Tables 1 and 2. The method of measuring base temperature rise shall be as described in ANSI C78.25. A recommended method of electrical measurement of lamps can be found in IES LM45. Screw-shell type bases, including the E39 mogul screw and E39d double-contact mogul screw Individual lamps shall satisy the limits for MOL and LCL that apply to their lamp class as shown 5 NEMA C78.22 95 6470247 0507230 860 ANSI C78.22-1995 10.3 occupy a space within th