ANSI NEMA C78.41-2016 Electric Lamps - Guidelines for Low- Pressure Sodium Lamps.pdf

1、NEMA Standards PublicationNational Electrical Manufacturers AssociationANSI C78.41-2016 Electric Lamps Guidelines for Low-Pressure Sodium LampsANSI C78.41-2016 Page 1 2016 National Electrical Manufacturers Association ANSI C78.41-2016 American National Standard for Electric Lamps Guidelines for Low-

2、Pressure Sodium Lamps Secretariat: National Electrical Manufacturers Association Approved: August 23, 2016 American National Standards Institute, Inc. 2016 National Electrical Manufacturers Association NOTICE AND DISCLAIMER The information in this publication was considered technically sound by the

3、consensus of persons engaged in the development and approval of the document at the time it was developed. Consensus does not necessarily mean that there is unanimous agreement among every person participating in the development of this document. ANSI standards and guideline publications, of which t

4、he document contained herein is one, are developed through a voluntary consensus standards development process. This process brings together volunteers and/or seeks out the views of persons who have an interest in the topic covered by this publication. While NEMA administers the process to promote f

5、airness in the development of consensus, it does not write the document and it does not independently test, evaluate, or verify the accuracy or completeness of any information or the soundness of any judgments contained in its standards and guideline publications. NEMA disclaims liability for any pe

6、rsonal injury, property, or other damages of any nature whatsoever, whether special, indirect, consequential, or compensatory, directly or indirectly resulting from the publication, use of, application, or reliance on this document. NEMA disclaims and makes no guaranty or warranty, expressed or impl

7、ied, as to the accuracy or completeness of any information published herein, and disclaims and makes no warranty that the information in this document will fulfill any of your particular purposes or needs. NEMA does not undertake to guarantee the performance of any individual manufacturer or sellers

8、 products or services by virtue of this standard or guide. In publishing and making this document available, NEMA is not undertaking to render professional or other services for or on behalf of any person or entity, nor is NEMA undertaking to perform any duty owed by any person or entity to someone

9、else. Anyone using this document should rely on his or her own independent judgment or, as appropriate, seek the advice of a competent professional in determining the exercise of reasonable care in any given circumstances. Information and other standards on the topic covered by this publication may

10、be available from other sources, which the user may wish to consult for additional views or information not covered by this publication. NEMA has no power, nor does it undertake to police or enforce compliance with the contents of this document. NEMA does not certify, test, or inspect products, desi

11、gns, or installations for safety or health purposes. Any certification or other statement of compliance with any health- or safety-related information in this document shall not be attributable to NEMA and is solely the responsibility of the certifier or maker of the statement. ANSI C78.41-2016 Page

12、 i 2016 National Electrical Manufacturers Association AMERICAN NATIONAL STANDARD Approval of an American National Standard requires verification by The American National Standards Institute, Inc. (ANSI) that the requirements for due process, consensus, and other criteria for approval have been met b

13、y the standards developer. An American National Standard implies a consensus of those substantially concerned with its scope and provisions. Consensus is established when, in the judgment of the ANSI Board of Standards Review, substantial agreement has been reached by directly, and materially affect

14、ed interests. Substantial agreement means much more than a simple majority, but not necessarily unanimity. Consensus requires that all views and objections be considered, and that a concerted effort be made toward their resolution. The existence of an American National Standard does not in any respe

15、ct preclude anyone, whether s/he has approved the standard or not, from manufacturing, marketing, purchasing, or using products, processes, or procedures not conforming to the standards. It is intended as a guide to aid the manufacturer, the consumer, and the general public. The American National St

16、andards Institute, Inc., does not develop standards and will in no circumstances give an interpretation of any American National Standard. Moreover, no person shall have the right or authority to issue an interpretation of an American National Standard in the name of the American National Standards

17、Institute, Inc. Requests for interpretations should be addressed to the secretariat or sponsor whose name appears on this title page. CAUTION NOTICE: This American National Standard may be revised or withdrawn at any time. The procedures of the American National Standards Institute, Inc., require th

18、at action be taken periodically to reaffirm, revise, or withdraw this standard. Purchasers of American National Standards may receive current information on all standards by calling or writing the American National Standards Institute, Inc. Published by National Electrical Manufacturers Association

19、1300 North 17thStreet, Suite 900 Rosslyn, Virginia 22209 2016 National Electrical Manufacturers Association All rights, including translation into other languages, reserved under the Universal Copyright Convention, the Berne Convention for the Protection of Literary and Artistic Works, and the Inter

20、national and Pan American copyright conventions. No part of this publication may be reproduced in any form, in an electronic retrieval system or otherwise, without prior written permission of the publisher. Printed in the United States of America ANSI C78.41-2016 Page ii 2016 National Electrical Man

21、ufacturers Association Foreword (This foreword is not part of ANSI C78.41-2016) Suggestions for improvement of this standard should be submitted to the C78 Secretariat, NEMA, 1300 North 17thStreet, Suite 900, Arlington, Virginia 22209. This American National Standard has been approved by the ANSI Ac

22、credited Standards Committee, C78. Approval of the standard does not necessarily imply that all members voted for approval.ANSI C78.41-2016 Page iii 2016 National Electrical Manufacturers Association CONTENTS Part IGeneral Information: Provides references to related American National standards and o

23、ffers brief explanations for some of the numerical data given on the individual lamp data sheets in Part II. 1 Scope . 1 2 Normative References . 1 3 Lamp Designations . 2 4 Bulb Designations . 2 5 Base Specifications 2 6 Maximum Outline Drawing . 2 7 Other Safety Requirements and Information. . 2 8

24、 Methods of Measurement . 3 9 Electrical Characteristics . 3 10 Reference Ballasts 3 11 Ballast Design . 3 12 Information for Luminaire Design . 3 Part IILamp Data Sheets: Contains individual lamp data sheets for each type of low-pressure sodium lamp. 18W low-pressure sodium lamp, L69 . 6 35W low-pr

25、essure sodium lamp, L70 . 8 55W low-pressure sodium lamp, L71 . 10 90W low-pressure sodium lamp, L72 . 12 135W low-pressure sodium lamp, L73 14 180W low-pressure sodium lamp, L74 16 Part IIIMaximum Outline Drawings: Contains the maximum outline drawings applicable to each lamp size. Maximum outline

26、drawing for L69, L70, L71 lamps . 19 Maximum outline drawing for L72, L73, L74 lamps . 20 ANSI C78.41-2016 Page iv 2016 National Electrical Manufacturers Association ANSI C78.41-2016 Page 1 2016 National Electrical Manufacturers Association Part I General Information 1 Scope This standard describes

27、the physical and electrical requirements of the principal types of single-ended low-pressure sodium lamps. The electrical data provides the specific basis for ballast requirements for these lamps. 2 Normative References The following standards contain provisions which, through reference in this text

28、, constitute provisions of this American National Standard. At the time of publication, the editions indicated were valid. All standards are subject to revision, and parties to agreements based on this American National Standard are encouraged to investigate the possibility of applying the most rece

29、nt editions of the standards indicated below. ANSI C78.30-1997 (R2011) American National Standard for Electric LampsProcedure for Use in Preparation of Lamp Space Drawings ANSI C78.380-2016 American National Standard for Electric LampsHigh-Intensity Discharge Lamps (HID)Method of Designation ANSI C7

30、8.389-2004 (R2009) American National Standard for Electric LampsHigh-Intensity Discharge (HID)Methods of Measuring Characteristics ANSI C78.79-2014 American National Standard for Electric LampsNomenclature for Envelope Shapes Intended for Use with Electric Lamps ANSI C81.61-2017 American National St

31、andard for Electrical Lamp BasesSpecifications for Bases (Caps) for Electric Lamps ANSI C81.62-2017 American National Standard for Electric Lampholders ANSI C81.63-2007 (R2014) American National Standard for Gauges for Electric Lamp Bases and Lampholders ANSI C81.64-2005 (R2014) American National St

32、andardGuidelines and General Information for Electrical Lamp Bases, Lampholders and Gauges ANSI C82.4-2002 (R2010) American National Standard for Lamp BallastsBallasts for High-Intensity Discharge and Low-Pressure Sodium (LPS) Lamps (Multiple-Supply Type) ANSI C82.5-2010 American National Standard f

33、or Reference BallastsHigh-Intensity-Discharge and Low-Pressure Sodium Lamps ANSI C82.9-2016 American National Standard for Lamp BallastsHigh-Intensity Discharge (HID) and Low-Pressure Sodium (LPS) LampsDefinitions ANSI C78.62035-2016 American National Standard for Electric LampsDischarge Lamps (Excl

34、uding Fluorescent Lamps)Safety Specifications ANSI C78.41-2016 Page 2 2016 National Electrical Manufacturers Association IEC 60061-1:2005 Lamp caps and holders together with gauges for the control of interchangeability and safetyPart 1: Lamp caps IEC 60192:2001 Low-pressure sodium vapour lampsPerfor

35、mance specifications 3 Lamp Designations Designations for low-pressure sodium lamps are assigned in accordance with ANSI C78.380. For reference, the older designations are shown in parentheses in the lamp data sheets. Note that the number (two or three digits) following the first letter in the desig

36、nation (L for low pressure sodium), indicates a unique set of electrical characteristics. Following the number is a slash followed by a luminaire characteristic letter. Low-pressure sodium lamps are typically used in enclosed luminaires and have a luminaire characteristic code of “E.” Marking low-pr

37、essure sodium lamps with the ANSI designation is not required. 4 Bulb Designations Bulb designations are defined in ANSI C79.1. Due to long-term use of the conventional method of bulb designations, that use will continue herein with the equivalent metric bulb designations shown in parentheses (i.e.,

38、 BT28 BT90) in contrast with the use of metric primary dimensions elsewhere in this standard. 5 Base Specifications The BY22d base is described in ANSI C81.61. 6 Maximum Outline Drawings The maximum outline drawings in Part III of this standard show the maximum limits of the space that may be occupi

39、ed by any part of the bulb for each lamp type. These limits are in accordance with IEC 60192. Most luminaires for low-pressure sodium lamps constrain the dome end of the lamp and take up any eccentricity of the lamp by means of a moveable base holder. Accordingly, the maximum outline drawings allow

40、for the maximum bulb diameter at the dome end and for eccentricity at the base end. 7 Other Safety Requirements and Information Lamps shall comply with the requirements of ANSI/IEC C78.62035. Low-pressure Sodium lamps contain a quantity of sodium that may heat from a reaction with moisture in the ai

41、r or on the skin if the lamp is broken. Sodium may burn spontaneously when exposed to air. Consult the lamp manufacturers literature for information on the proper use, care, and disposal of these lamps. ANSI C78.41-2016 Page 3 2016 National Electrical Manufacturers Association 8 Methods of Measureme

42、nt An American National Standard for methods of measuring the electrical characteristics and the bulb and base temperatures of low-pressure sodium lamps has not been written. General guidelines for these measurements may be found in ANSI C78.389 and IEC 60192. 9 Electrical Characteristics 9.1 Lamp O

43、perating Characteristics The values of lamp volts, amperes, and watts shown on the individual lamp data sheets in Part II of this standard apply for lamps that have aged 100 hours. Lamp rms voltage may increase with operating hours. Contact the lamp manufacturer for details. 9.2 Warm-up Time Bare la

44、mps operating in still air shall reach a stabilized voltage within the time limit and at the ambient temperature specified on the applicable lamp data sheet in Part II of this standard. For purposes of this test, low-pressure sodium lamps have reached a stabilized voltage when their voltage does not

45、 vary more than 2% in any one-minute period. Lamps shall meet this requirement when operated on the appropriate reference ballast specified in Part II, section 4, and in the allowed operating position most adverse to warm-up. 10 Reference Ballasts Reference ballasts shall meet the general requiremen

46、ts described in ANSI C82.5. 11 Ballast Design General ballast requirements are described in ANSI C82.4. The following requirements shall be met over the full range of input voltage allowed for the ballast. 11.1 Open Circuit Voltage The minimum ballast open circuit voltages shown on the individual la

47、mp data sheets assure starting and operating reliability over lamp life. The percentage probability has not yet been determined. 11.2 Starting Current Starting current shall be measured 515 seconds after the lamp has been energized and shall be within the limits shown on the applicable lamp data she

48、et. 12 Information for Luminaire Design 12.1 Lamp Temperatures Luminaire design shall be such that the maximum lamp temperatures given in the physical characteristics section of the relevant lamp data sheet of Part II are not exceeded. 12.2 Lamp Operating Position A luminaire shall maintain the lamp

49、 within its allowable operating position limits. ANSI C78.41-2016 Page 4 2016 National Electrical Manufacturers Association 12.3 Maximum Lamp Outlines The information in clause 6 and the maximum lamp outlines in Part III provide guidance for the designers of luminaires. For mechanical acceptance of lamps complying with this standard, a free space should be provided in the luminaires based on these maximum outlines. ANSI C78.41-2016 Page 5 2016 National Electrical Manufacturers Association Part II Lamp Data Sheets ANSI C7