ANSI NEMA C78.52-2017 Electric Lamps - LED (Light Emitting Diode) Direct Replacement Lamps - Method of Designation.pdf

1、NEMA Standards PublicationNational Electrical Manufacturers AssociationANSI C78.52-2017Electric Lamps LED (Light Emitting Diode) Direct Replacement Lamps Method of DesignationANSI C78.52-2017 American National Standard for Electric Lamps LED (Light Emitting Diode) Direct Replacement Lamps Method of

2、Designation Secretariat: National Electrical Manufacturers Association Approved: February 2, 2017 American National Standards Institute, Inc. 2017 National Electrical Manufacturers Association NOTICE AND DISCLAIMER The information in this publication was considered technically sound by the consensus

3、 of persons engaged in the development and approval of the document at the time it was developed. Consensus does not necessarily mean that there is unanimous agreement among every person participating in the development of this document. ANSI standards and guideline publications, of which the docume

4、nt contained herein is one, are developed through a voluntary consensus standards development process. This process brings together volunteers and/or seeks out the views of persons who have an interest in the topic covered by this publication. While NEMA administers the process to promote fairness i

5、n the development of consensus, it does not write the document and it does not independently test, evaluate, or verify the accuracy or completeness of any information or the soundness of any judgments contained in its standards and guideline publications. NEMA disclaims liability for any personal in

6、jury, property, or other damages of any nature whatsoever, whether special, indirect, consequential, or compensatory, directly or indirectly resulting from the publication, use of, application, or reliance on this document. NEMA disclaims and makes no guaranty or warranty, expressed or implied, as t

7、o the accuracy or completeness of any information published herein, and disclaims and makes no warranty that the information in this document will fulfill any of your particular purposes or needs. NEMA does not undertake to guarantee the performance of any individual manufacturer or sellers products

8、 or services by virtue of this standard or guide. In publishing and making this document available, NEMA is not undertaking to render professional or other services for or on behalf of any person or entity, nor is NEMA undertaking to perform any duty owed by any person or entity to someone else. Any

9、one using this document should rely on his or her own independent judgment or, as appropriate, seek the advice of a competent professional in determining the exercise of reasonable care in any given circumstances. Information and other standards on the topic covered by this publication may be availa

10、ble from other sources, which the user may wish to consult for additional views or information not covered by this publication. NEMA has no power, nor does it undertake to police or enforce compliance with the contents of this document. NEMA does not certify, test, or inspect products, designs, or i

11、nstallations for safety or health purposes. Any certification or other statement of compliance with any health- or safety-related information in this document shall not be attributable to NEMA and is solely the responsibility of the certifier or maker of the statement. ANSI C78.52-2017 Page i AMERIC

12、AN NATIONAL STANDARD Approval of an American National Standard requires verification by The American National Standards Institute, Inc. (ANSI) that the requirements for due process, consensus, and other criteria for approval have been met by the standards developer. An American National Standard imp

13、lies a consensus of those substantially concerned with its scope and provisions. Consensus is established when, in the judgment of the ANSI Board of Standards Review, substantial agreement has been reached by directly, and materially affected interests. Substantial agreement means much more than a s

14、imple majority, but not necessarily unanimity. Consensus requires that all views and objections be considered, and that a concerted effort be made toward their resolution. The existence of an American National Standard does not in any respect preclude anyone, whether s/he has approved the standard o

15、r not, from manufacturing, marketing, purchasing, or using products, processes, or procedures not conforming to the standards. It is intended as a guide to aid the manufacturer, the consumer, and the general public. The American National Standards Institute, Inc., does not develop standards and will

16、 in no circumstances give an interpretation of any American National Standard. Moreover, no person shall have the right or authority to issue an interpretation of an American National Standard in the name of the American National Standards Institute, Inc. Requests for interpretations should be addre

17、ssed to the secretariat or sponsor whose name appears on this title page. CAUTION NOTICE: This American National Standard may be revised or withdrawn at any time. The procedures of the American National Standards Institute, Inc., require that action be taken periodically to reaffirm, revise, or with

18、draw this standard. Purchasers of American National Standards may receive current information on all standards by calling or writing the American National Standards Institute, Inc. Published by National Electrical Manufacturers Association 1300 North 17thStreet, Suite 900 Rosslyn, Virginia 22209 201

19、7 National Electrical Manufacturers Association All rights, including translation into other languages, reserved under the Universal Copyright Convention, the Berne Convention for the Protection of Literary and Artistic Works, and the International and Pan American copyright conventions. No part of

20、this publication may be reproduced in any form, in an electronic retrieval system or otherwise, without prior written permission of the publisher. Printed in the United States of America ANSI C78.52-2017 Page ii 2017 National Electrical Manufacturers Association Foreword (This foreword is not part o

21、f ANSI C78.52-2017) This is a new standard recently developed by American National Standards Committee C78 on Electric Lamps. It is not a revision of a previous standard. Suggestions for improvement of this standard will be welcome. They should be sent to The National Electrical Manufacturers Associ

22、ation, 1300 North 17thStreet, Suite 900, Rosslyn, VA 22209. This standard was developed and approved for submittal to ANSI by Accredited Standards Committee on Electric Lamps. Approval of this standard is not meant to imply that all Accredited Standards Committee members voted to approve it. ANSI C7

23、8.52-2017 Page iii 2017 National Electrical Manufacturers Association CONTENTS Foreword ii 1 Scope 1 2 Purpose . 1 3 References 1 3.1 Normative References 1 3.2 Informative References . 2 4 Definitions . 2 5 Description of a Designation 3 5.1 General . 3 5.2 Lamp Type Classification Letter 3 5.3 Cha

24、racteristic Number 3 5.4 Special Characteristic Letter . 4 6 The Practice of Lamp Code Designations (LCD) Becoming American National Standard . 4 Annexes Annex A1 Direct Replacements for Incandescent and Tungsten Halogen Lamps . 5 Annex A2 Direct Replacements for single and double ended fluorescent

25、Lamps 48 Annex A3 Direct Replacements for High Intensity Discharge Lamps . 56 Annex B Special Characteristic Letters . 59 Annex C Additional Characteristics Affecting Interchangeability . 59 ANSI C78.52-2017 Page 1 1 Scope This standard describes a system for the designation of LED lamps that are di

26、rect replacements for existing ANSI standardized non-LED lamps. Lamps covered in this standard contain LED-based light sources. OLED lamps are not included at this time. 2 Purpose The purpose of the designation system covered by this standard is to provide an identification code for use in ANSI stan

27、dards. Some lamp marking requirements are also identified. Guidance is given as to which characteristics are essential to assure interchangeability for safe operation and which characteristics affect performance. The lamp characteristic data given by a manufacturer on an LED (Light-Emitting Diode) D

28、irect Replacement Lamp Code Designation Request Form becomes the basis for the assignment of a designation. They have not been approved by the American National Standards Institute (ANSI) and do not constitute an American National Standard. Similarly, any consolidated listing of assigned designation

29、s with associated characteristics does not constitute an American National Standard. 3 References The following standards contain provisions that, through reference in this text, constitute provisions of this American National Standard. At the time of publication, the editions indicated were valid.

30、All standards are subject to revision, and parties to agreements based on this American National Standard are encouraged to investigate the possibility of applying the most recent editions of the standards indicated below. 3.1 Normative References ANSI C78.30-1997 American National Standard for Elec

31、tric LampsProcedure for Use in Preparation of Lamp Space DrawingsANSI C78.377-2015 American National Standard for Electric LampsSpecifications for the Chromaticity of Solid State Lighting (SSL) Products ANSI C78.379-2006 (R2015) American National Standard for Electric LampsClassification of the Beam

32、 Patterns of Reflector Lamps ANSI C78.380-2016 American National Standard for Electric LampsHigh-Intensity Discharge (HID)Method of Designation ANSI C81.61-2017 American National Standard for Electrical Lamp BasesSpecifications for Bases (Caps) for Electric Lamps ANSI C81.62-2017 American National S

33、tandard for Electric Lamp Holders ANSI C81.63-2007(R2014) American National Standard for Gauges for Electric Lamp Bases and Lampholders ANSI C81.64-2005 (R2014) American National StandardGuidelines and General Information for Electrical Lamp Bases, Lampholders and Gauges ANSI C82.5-2016 American Nat

34、ional Standard for Reference BallastsHigh-Intensity-Discharge and Low-Pressure Sodium Lamps ANSI/UL1 598-2008 Standard for SafetyLuminaires IES RP-16-10 Nomenclature and Definitions for Illuminating Engineering ANSI C78.52-2017 Page 2 2017 National Electrical Manufacturers Association 3.2 Informativ

35、e References ANSI C78.20-2003 (R2007, R2015) American National Standard for Electric LampsA, G, PS, and Similar Shapes with E26 Medium Screw Bases ANSI C78.21-2011(R2016) American National Standard for Electric LampsPAR and R Shapes ANSI C78.22-1995 (R2003) American National Standard for Incandescen

36、t LampsA, G, PS and Similar Shapes with E39 Mogul Screw Bases ANSI C78.23-1995 (R2003) American National Standard for Incandescent LampsMiscellaneous Types ANSI C78.24-2001 American National Standard for Electric LampsTwo-inch (51 mm) Integral-Reflector Lamps with Front Covers and GU5.3 or GX5.3 Bas

37、es ANSI C78.42-2009 (R2016) American National Standard for Electric LampsHigh-Pressure Sodium (HPS) Lamps ANSI C78.43-2013 American National Standard for Electric LampsSingle-Ended Metal Halide Lamps ANSI C78.44-2016 American National Standard for Electric LampsDouble-Ended Metal Halide Lamps ANSI C

38、78.50-2016 American National Standard for Electric LampsAssigned LED Lamp Codes ANSI C78.79-2014 American National Standard for Electric LampsNomenclature for Envelope Shapes Intended for Use with Electric Lamps ANSI C78.81-2016 American National Standard for Electric LampsDouble-Capped Fluorescent

39、LampsDimensional and Electrical Characteristics NEMA SSL 6-2010 Solid State Lighting for Incandescent ReplacementDimming ANSI/IEC C78.682-1997 American National Standard for Electric LampsStandard Method of Measuring Pinch Temperature of Quartz Tungsten-Halogen Lamps ANSI C78.1413-2001 American Nati

40、onal Standard for Dimensions and Centering Systems for Projection Lamps51 mm (2 in.) Integral Reflector, Rim Reference Lamps with GX5.3, GY5.3 and GU5.3 Bases UL1993 Safety Standard for Self Ballasted Lamps and Adapters 4 Definitions alternative design: A lamp with key characteristics that are the s

41、ame but utilize different features that do not affect interchangeability. direct replacement lamp: A light source provided with a standard lamp base and additional internal components necessary for starting and stable operation, designed to replace at least one existing non-LED lamp without modifica

42、tion of the luminaire. designation program: The procedures and requirements of this standard formulated to provide designations for lamps. electrical interchangeability: The ability to operate a replacement lamp in an installation where electrical characteristics of lamps and luminaires are compatib

43、le in regard to characteristics such as voltage, current, power, open circuit voltage, etc. ANSI C78.52-2017 Page 3 2017 National Electrical Manufacturers Association lamp manufacturer: A manufacturer who produces finished lamps and offers them for sale. light center length (LCL): Distance from the

44、reference plane (eyelet solder or equivalent for screw bases) to the center of the light-emitting element of the lamp. physical interchangeability: The ability to properly install a replacement lamp in a particular installation, based on physical characteristics such as base type, lamp size, lamp le

45、ngth, etc. key characteristic: A characteristic identified as having a critical effect on the interchangeability of lamps. maximum overall length (MOL): Distance along the lamp axis from furthest base extension (eyelet solder for screw bases) to the top or face of the lamp. maximum seating plane (MS

46、P): Distance in millimeters from the seating plane to the end of the base. The seating plane is that part of the reflector or lens intended to lay or seat against the housing. self-ballasted lamp: A device provided with a lamp base and incorporating a non-replaceable light source and any additional

47、elements necessary for starting and stabilizing operation of the light source, which cannot be dismantled without being permanently damaged. sponsor: The originator of a lamp code designation request form. 5 Description of a Designation 5.1 General A direct LED replacement lamp designation code shal

48、l consist of a combination of letters and numbers in the following sequence: a. Lamp Type Classification Letter (SLR) b. Characteristic Number (See Annex A1, A2, & A3) c. Special Characteristic Letter(s) (optional) The lamp designation code should be marked on the lamps or on the product packaging.

49、5.2 Lamp Type Classification Letters The code for direct LED replacement lamp type classification shall be SLR Refer to annex A1 through A3 for the current SLR codes. 5.3 Characteristic Number The direct LED replacement lamp code characteristic number is technology dependent and is based on existing ANSI lamp codes for incumbent lamp technologies. This standard provides a designation system for the following lamp technologies: a. Incandescent (INC) b. Halogen (HAL) c. Linear Fluorescent (LFL) d. Compact Fluorescent (CFL) e. High Intensity