ANSI TIA EIA 455-41A-1993 Compressive Loading Resistance of Fiber Optic Cable《光缆的耐压负荷》.pdf

1、ANSI/TIA/EIA-455-41A-l993 Approved: November 2, 1993 Reaffirmed: December 26, 2001 The Teleconmiunications Industry Association represents the conmiunications sector of Copyright Electronic Industries Alliance Provided by IHS under license with EIANot for ResaleNo reproduction or networking permitte

2、d without license from IHS-,-,-NOTICE TIA/EIA Engineering Standards and Publications are designed to serve the public interest through eliminating misunderstandings between manufacturers and purchasers, facilitating interchangeability and improvement of products, and assisting the purchaser in selec

3、ting and obtaining with minimum delay the proper product for his particular need. Existence of such Standards and Publications shall not in any respect preclude any member or nonmember of TIA/EIA from manufacturing or selling products not conforming to such Standards and Publications, nor shall the

4、existence of such Standards and Publications preclude their voluntary use by those other than TIA/EIA members, whether the standard is to be used either domestically or internationally. Standards and Publications are adopted by TIA/EIA in accordance with the American National Standards Institute (AN

5、SI) patent policy. By such action, TIA/EIA does not assume any liability to any patent owner, nor does it assume any obligation whatever to parties adopting the Standard or Publication. This Standard does not purport to address all safety problems associated with its use or all applicable regulatory

6、 requirements. It is the responsibility of the user of this Standard to establish appropriate safety and health practices and to determine the applicability of regulatory limitations before its use. (From Standards Proposal No. 3-3884-RF1, formulated under the cognizance of the TIA FO-6.6 Subcommitt

7、ee on Optical Fibers.) This Document was reaffirmed by the American National Standards Institute (ANSI) on December 26,200 1, and by the TIA. Published by TELECOMMUNICATIONS INDUSTRY ASSOCIATION 1998 Standards and Technology Department 2500 Wilson Boulevard Arlington, VA 22201 U.S.A. PRICE: Please r

8、efer to current Catalog of EIA ELECTRONIC INDUSTRIES ALLIANCE STANDARDS and ENGINEERING PUBLICATIONS or call Global Engineering Documents, USA and Canada (1 -800-854-7 179) International (303-397-7956) All rights reserved Printed in U.S.A. Copyright Electronic Industries Alliance Provided by IHS und

9、er license with EIANot for ResaleNo reproduction or networking permitted without license from IHS-,-,-Copyright Electronic Industries Alliance Provided by IHS under license with EIANot for ResaleNo reproduction or networking permitted without license from IHS-,-,-NOTICE OF DISCLAIMER AND LIMITATION

10、OF LIABILITY The document to which this Notice is affixed has been prepared by one or more Engineering Committees of the Telecommunications Industry Association (“TIA”). TIA is not the author of the document contents, but publishes and claims copyright to the document pursuant to licenses and permis

11、sion granted by the authors of the contents. TIA Engineering Committees are expected to conduct their affairs in accordance with the TIA Engineering Manual (“Manual”), the current and predecessor versions of which are available at http:/www.tiaonline.orZr/standards/sfZr/engineering manual.ch. TIAS f

12、unction is to administer the process, but not the content, of document preparation in accordance with the Manual and, when appropriate, the policies and procedures of the American National Standards Institute (“ANSI”). THE USE OR PRACTICE OF CONTENTS OF THIS DOCUMENT MAY INVOLVE THE USE OF INTELLECT

13、UAL PROPERTY RIGHTS (“IPR), INCLUDING PENDING OR ISSUED PATENTS, OR COPYRIGHTS, OWNED BY ONE OR MORE PARTIES. TIA MAKES NO SEARCH OR INVESTIGATION FOR IPR. WHEN IPR CONSISTING OF PATENTS AND PUBLISHED PATENT APPLICATIONS ARE CLAIMED AND CALLED TO TIAS ATTENTION, A STATEMENT FROM THE HOLDER THEREOF I

14、S REQUESTED, ALL IN ACCORDANCE WITH THE MANUAL. TIA TAKES NO POSITION WITH REFERENCE TO, AND DISCLAIMS ANY OBLIGATION TO INVESTIGATE OR INQUIRE INTO, THE SCOPE OR VALIDITY OF ANY CLAIMS OF IPR. ALL WARRANTIES, EXPRESS OR IMPLIED, ARE DISCLAIMED, INCLUDING WITHOUT LIMITATION, ANY AND ALL WARRANTIES C

15、ONCERNING THE ACCURACY OF THE CONTENTS, ITS FITNESS OR APPROPRIATENESS FORA PARTICULAR PURPOSE PARTYS INTELLECTUAL PROPERTY RIGHTS. TIA EXPRESSLY DISCLAIMS ANY AND ALL RESPONSIBILITIES FOR THE ACCURACY OF THE CONTENTS AND MAKES NO REPRESENTATIONS OR WARRANTIES REGARDING THE CONTENTS COMPLIANCE WITH

16、ANY APPLICABLE STATUTE, RULE OR REGULATION. OR USE, ITS MERCHANTABILITY AND ITS NON-INFRINGEMENT OF ANY THIRD TIA SHALL NOT BE LIABLE FOR ANY AND ALL DAMAGES, DIRECT OR INDIRECT, ARISING FROM OR RELATING TO ANY USE OF THE CONTENTS CONTAINED HEREIN, INCLUDING WITHOUT LIMITATION ANY AND ALL INDIRECT,

17、SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES (INCLUDING DAMAGES FOR LOSS OF BUSINESS, LOSS OF PROFITS, LITIGATION, OR THE LIKE), WHETHER BASED UPON BREACH OF CONTRACT, BREACH OF WARRANTY, TORT (INCLUDING NEGLIGENCE), PRODUCT LIABILITY OR OTHERWISE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.

18、 THE FOREGOING NEGATION OF DAMAGES IS A FUNDAMENTAL ELEMENT OF THE USE OF THE CONTENTS HEREOF, AND THESE CONTENTS WOULD NOT BE PUBLISHED BY TIA WITHOUT SUCH LIMITATIONS. Copyright Electronic Industries Alliance Provided by IHS under license with EIANot for ResaleNo reproduction or networking permitt

19、ed without license from IHS-,-,-EIA TIA-455-4LA 93 3234600 0552372 441 o Reproduced By GUML ENGINEERING DOCUMENTS 3 With lhe Permission of EIA Under Royalty Agreement TIAIEIA STANDARD ANSI/ TIA/ EIA- 4 5 5- 41A- 19 9 3 APPROVED: November 2, 1993 FOTP-41 Compressive Loading Resistance of - Fiber Opti

20、c Cables (Revision of EIA-455-41) DECEMBER 1993 TELECOMMUNICATIONS INDUSTRY ASSOCIATION Copyright Electronic Industries Alliance Provided by IHS under license with EIANot for ResaleNo reproduction or networking permitted without license from IHS-,-,-EIA TIA-q55-q3A 93 3234600 0552373 388 NOTICE TIA/

21、EIA Engineering Standards and Publications are designed to serve the public interest through eliminating misunderstandings between manufacturers and purchasers, facilitating interchangeability and improvement of products, and assisting the purchaser in selecting and obtaining with minimum delay the

22、proper product for his particular need. Existence of such Standards and Publications shall not in any respect preclude any member or nonmember of TIA/EIA from manufacturing or selling products not conforming to such Standards and Publications, nor shall the existence of such Standards and Publicatio

23、ns preclude their voluntary use by those other than TIA/EIA members, whether the standard is to be used either domestically or internationally. Recommended Standards and Publications are adopted by TIA/EIA in accordance with the American National Standards Institute (ANSI) patent policy. By such act

24、ion, TIA/ElA does not assume any liability to any patent owner, nor does it assume any obligation whatever to parties adopting the Recommended Standard or Publication. This Standard does not purport to address all safety problems associated with its use or all applicable regulatory requirements. It

25、is the responsibility of the user of this Standard to establish appropriate safety and health practices and to determine the applicability of regulatory limitations before its use. Published by TELECOMMUNICATIONS INDUSTRY ASSOCIATION Standards and Technology Department 2001 Pennsylvania Avenue N. W.

26、 Washington, D.C. 20006 ELECTRONIC INDUSTRIES ASSOCIATION 1993 All rights reserved Printed in U.S.A. PRICE: Please refer to current Catalog of EIA 6.2.2 of the compressive force; If specified, the fibers shall not be broken as a result 6.2.3 There shall be no cracking, splitting, or similar damage o

27、f the cable exterior, and 6.2.4 Cable exterior deformation shall not be considered as damage. 6.3 Precision and Bias. No statement is made about either the precision or bias of FOTP-41 for measuring compressive loading resistance. The results merely state whether there is conformance to the criteria

28、 for success specified in the procedure. Copyright Electronic Industries Alliance Provided by IHS under license with EIANot for ResaleNo reproduction or networking permitted without license from IHS-,-,-_ EIA TIA-455-4LA 93 3234600 0552383 227 = TIA/EIA-455-41A Page 8 7. DOCUMENTATION 7.1 Report the

29、 following information for each test: 7.1.1 Date of test. 7.1.2 Identification of procedure use (FOTP-41). 7.1.3- Sample identification and description, including cable length tested. 7.1.4 Maximum load applied and the loading rate. 7.1.5 If optical measurements are required: 7.1.5.1 The optical tes

30、t procedure and equipment used (3.4). 7.1.5.2 Appropriate identification of the fibers tested (number of fibers, distribution in units, etc.) (5.3). 7.1.5.3 The initial and final power readings and the calculated loss, or the measured attenuation (5.3 and 5.5). 7.1.5.4 The optical power or attenuati

31、on readings while under load, when measured (5.4). O - 7.1.6 Visual observations and damage assessments made. 7.1.7 Conformance to the acceptance criteria. 7.2 United States military applications require that the following information also be reported for each test. For other (nonmilitary) applicati

32、ons, this information need not be reported but shall be available for review upon request. 7.2.1 Identification of test personnel. 7.2.2 Detailed information on equipment used (model number, serial number, etc.) and calibration dates. 7.2.3 If optical measurement is required: 7.2.3.1 Type and wavele

33、ngth of source. 7.2.3.2 Description of launch conditions used. 7.2.3.3 Description of cladding mode strippers, if applicable. 7.2.3.4 Description of detection and recording equipment. Copyright Electronic Industries Alliance Provided by IHS under license with EIANot for ResaleNo reproduction or netw

34、orking permitted without license from IHS-,-,-EIA TIA-455-4LA 93 3234600 0552384 Lb3 - 8.4.2 The number of fibers to be tested (5.3). TIA/EIA-455-41A Page 9 8. SPECIFICATION INFORMATION The following information shall be specified in the Detail Specification: 8.1 A reference to this test procedure.

35、8.2 Any exceptions or deviations that apply to this test procedure, including: 8.2.1 Specimen length limits, if other than stated in the procedure (4.2) . 8.2.2 Conditioning requirements and test conditions, if other than standard (5.1). 8.2.3 Any other deviations. 8.3 The compressive load to be app

36、lied, the loading rate, and the interval for which is load is maintained. 8.4 Whether optical measurements are required, and if so: 8.4.1 Optical source wavelenqth to be used. 8.4.3 Whether optical measurements are required during the compressive loading, and if so, the required measurement interval

37、(s) (5.4 and 5.5). 8.5 Acceptance or failure criteria. 8.6 Other requirements, if applicable. Copyright Electronic Industries Alliance Provided by IHS under license with EIANot for ResaleNo reproduction or networking permitted without license from IHS-,-,-EIA TIA-455-41A 93 3234b00 0552185 OTT D . T

38、IA/EIA-455-41A Page 10 c APPENDIX COMPARISON BETWEEN FOTP-41 AND IEC, SIO, AND CCITT REQUIREMENTS (Nonmandatory Information) B.l IEC Reference is made to IEC 794-1, Second Edition (1987), “Optical fibre cables, Part 1: Generic Specification,“ and to IEC 794-2, Second Edition (1989-lo), “Optical fibr

39、e cables, Part 2: Product specifications. I Clause 12 of IEC 704-1 covers “Method IEC 794-1-E3 - Crush,“ which is a method essentially the same as FOTP-41. IEC 794-1 reqires testing at 15 to 35OC, 25 to 75% relative humidity, and 86 to 106 kPa air pressure, which does not completely agree with FOTP-

40、41. IEC 794-1 also specifies that if the load is applied in incremental steps, the steps shall not exceed a ratio of 1.5:l. IEC 794-1, like FOTP-41, defers to the Detail Specification for other test conditions and requirements. As examples of Detail Specification requirements, Clause 6.2 of IEC 794-

41、2 deals with a single fiber cable. It calls for a minimum radius of curvature of the movable plate of 5 mm, and a 500 N load applied for 1 minute, with no fiber breakage allowed. Clause 10.2.2 relates to a dual fiber cable; it calls for a minimum of a 5 mm radius movable plate curvature, and a 1000

42、N load applied for 1 minute, with no fiber breakage allowed. B.2 IS0 No comparable IS0 tests have been identified or reviewed. B.3 CCITT It should be noted that, as of this publication date, there are no known CCITT test methods that are comparable to this FOTP. Copyright Electronic Industries Allia

43、nce Provided by IHS under license with EIANot for ResaleNo reproduction or networking permitted without license from IHS-,-,-EIA TIA-455-4LA 93 323YbOO 0552186 T3b Copyright Electronic Industries Alliance Provided by IHS under license with EIANot for ResaleNo reproduction or networking permitted without license from IHS-,-,-