ANSI TIA EIA 561-1990 Simple 8-Position Non-Synchronous Interface between Data Terminal Equipment and Data Circuit-Terminating Equipment Employing Serial Data Interchange《用串联数据交换的数.pdf

1、 TIA STANDARD ANSI/TIA/EIA-561-1990 Approved: March 20, 1990 Reaffirmed: December 10, 1998 Reaffirmed: May 20, 2003 Simple 8-Position Non-Synchronous Interface Between Data Terminal Equipment and Data Circuit-Terminating Equipment Employing Serial Binary Data Interchange TIA-561 OCTOBER 1990 TELECOM

2、MUNICATIONS INDUSTRY ASSOCIATION Representing the telecommunications industry in association with the Electronic Industries Alliance Copyright Electronic Industries Alliance Provided by IHS under license with EIANot for ResaleNo reproduction or networking permitted without license from IHS-,-,-NOTIC

3、E TIA Engineering Standards and Publications are designed to serve the public interest through eliminating misunderstandings between manufacturers and purchasers, facilitating interchangeability and improvement of products, and assisting the purchaser in selecting and obtaining with minimum delay th

4、e proper product for their particular need. The existence of such Standards and Publications shall not in any respect preclude any member or non-member of TIA from manufacturing or selling products not conforming to such Standards and Publications. Neither shall the existence of such Standards and P

5、ublications preclude their voluntary use by Non-TIA members, either domestically or internationally. Standards and Publications are adopted by TIA in accordance with the American National Standards Institute (ANSI) patent policy. By such action, TIA does not assume any liability to any patent owner,

6、 nor does it assume any obligation whatever to parties adopting the Standard or Publication. Further details of the development process are available in the TIA Engineering Manual, located at http:/www.tiaonline.org/standards/sfg/engineering_manual.cfm This Standard does not purport to address all s

7、afety problems associated with its use or all applicable regulatory requirements. It is the responsibility of the user of this Standard to establish appropriate safety and health practices and to determine the applicability of regulatory limitations before its use. (From Standards Proposal No. 3-409

8、2-RF2, formulated under the cognizance of the TIA TR-30.2 Subcommittee on DTE-DCE Interfaces and Protocols.) This Document was reaffirmed by the American National Standards Institute (ANSI) on May 20, 2003 and by the TIA. Published by TELECOMMUNICATIONS INDUSTRY ASSOCIATION 1990 Standards and Techno

9、logy Department 2500 Wilson Boulevard Arlington, VA 22201 U.S.A. PRICE: Please refer to current Catalog of TIA TELECOMMUNICATIONS INDUSTRY ASSOCIATION STANDARDS AND ENGINEERING PUBLICATIONS or call Global Engineering Documents, USA and Canada (1-800-854-7179) International (303-397-7956) or search o

10、nline at http:/www.tiaonline.org/standards/search_n_order.cfm All rights reserved Printed in U.S.A Copyright Electronic Industries Alliance Provided by IHS under license with EIANot for ResaleNo reproduction or networking permitted without license from IHS-,-,-NOTICE OF DISCLAIMER AND LIMITATION OF

11、LIABILITY The document to which this Notice is affixed (the “Document”) has been prepared by one or more Engineering Committees or Formulating Groups of the Telecommunications Industry Association (“TIA”). TIA is not the author of the Document contents, but publishes and claims copyright to the Docu

12、ment pursuant to licenses and permission granted by the authors of the contents. TIA Engineering Committees and Formulating Groups are expected to conduct their affairs in accordance with the TIA Engineering Manual (“Manual”), the current and predecessor versions of which are available at http:/www.

13、tiaonline.org/standards/sfg/engineering_manual.cfm. TIAs function is to administer the process, but not the content, of document preparation in accordance with the Manual and, when appropriate, the policies and procedures of the American National Standards Institute (“ANSI”). TIA does not evaluate,

14、test, verify or investigate the information, accuracy, soundness, or credibility of the contents of the Document. In publishing the Document, TIA disclaims any undertaking to perform any duty owed to or for anyone. The use or practice of contents of this Document may involve the use of intellectual

15、property rights (“IPR”), including pending or issued patents, or copyrights, owned by one or more parties. TIA makes no search or investigation for IPR. When IPR consisting of patents and published pending patent applications are claimed and called to TIAs attention, a statement from the holder ther

16、eof is requested, all in accordance with the Manual. TIA takes no position with reference to, and disclaims any obligation to investigate or inquire into, the scope or validity of any claims of IPR. TIA does not enforce or monitor compliance with the contents of the Document. TIA does not certify, i

17、nspect, test or otherwise investigate products, designs or services or any claims of compliance with the contents of the Document. ALL WARRANTIES, EXPRESS OR IMPLIED, ARE DISCLAIMED, INCLUDING WITHOUT LIMITATION, ANY AND ALL WARRANTIES CONCERNING THE ACCURACY OF THE CONTENTS, ITS FITNESS OR APPROPRI

18、ATENESS FOR A PARTICULAR PURPOSE OR USE, ITS MERCHANTABILITY AND ITS NON-INFRINGEMENT OF ANY THIRD PARTYS INTELLECTUAL PROPERTY RIGHTS. TIA EXPRESSLY DISCLAIMS ANY AND ALL RESPONSIBILITIES FOR THE ACCURACY OF THE CONTENTS AND MAKES NO REPRESENTATIONS OR WARRANTIES REGARDING THE CONTENTS COMPLIANCE W

19、ITH ANY APPLICABLE STATUTE, RULE OR REGULATION, OR THE SAFETY OR HEALTH EFFECTS OF THE CONTENTS OR ANY PRODUCT OR SERVICE REFERRED TO IN THE DOCUMENT OR PRODUCED OR RENDERED TO COMPLY WITH THE CONTENTS. TIA SHALL NOT BE LIABLE FOR ANY AND ALL DAMAGES, DIRECT OR INDIRECT, ARISING FROM OR RELATING TO

20、ANY USE OF THE CONTENTS CONTAINED HEREIN, INCLUDING WITHOUT LIMITATION ANY AND ALL INDIRECT, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES (INCLUDING DAMAGES FOR LOSS OF BUSINESS, LOSS OF PROFITS, LITIGATION, OR THE LIKE), WHETHER BASED UPON BREACH OF CONTRACT, BREACH OF WARRANTY, TORT (INCLUDING NEG

21、LIGENCE), PRODUCT LIABILITY OR OTHERWISE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. THE FOREGOING NEGATION OF DAMAGES IS A FUNDAMENTAL ELEMENT OF THE USE OF THE CONTENTS HEREOF, AND THESE CONTENTS WOULD NOT BE PUBLISHED BY TIA WITHOUT SUCH LIMITATIONS. Copyright Electronic Industries Allia

22、nce Provided by IHS under license with EIANot for ResaleNo reproduction or networking permitted without license from IHS-,-,-PLEASE! DONT VIOLATE THE LAW! This document is copyrighted by the TIA and may not be reproduced without prior permission of the Telecommunications Industry Association. For in

23、formation consult our website at http:/www.tiaonline.org/about/faqDetail.cfm?id=18 Organizations may obtain permission to reproduce a limited number of copies through entering into a license agreement. For information, contact: Global Engineering Documents 15 Inverness Way East Englewood, CO 80112-5

24、704 U.S.A. or call U.S.A. and Canada 1-800-854-7179, International (303) 397-7956 Copyright Electronic Industries Alliance Provided by IHS under license with EIANot for ResaleNo reproduction or networking permitted without license from IHS-,-,-. EIX/TIA-SGl CONTENTS i . SCOPE i 1.1 GENERAL 1 1.2 CON

25、NECTION . i 1.3 BITSEQUENCES i 1.4 DATA SIGNALING RATES . i 2 . INTERFACE MECHANICAL CHARACTERISTICS 2 2.1 POINT OF INTERFACE 2 2.2 INTERFACE CONNECTOR . 2 2.3 CONNECTOR CONTACT ASSIGNMENTS 7 3.1 GENERAL 8 3.2 CLASSIFICATION OF CIRCUITS . 8 3.3 SIGNAL CHARACTERISTICS, GENERAL 9 3.4 DEFINITIONS OF IN

26、TERCHANGE CIRCUITS 9 . 1.5 NON-SYNCHRONOUSCOMMUNICATION . 1 3 . FUNCTIONAL DESCRIPTIONS OF THE INTERCHANGE CIRCUITS 8 LIST OF FIGURES Figure 2.1 . 2 Figure 2.2 . 3 Figure 2.3 . 3 Figure 2.4 . 4 Figure 2.5 . 5 Figure 2.6 . 6 Figure 2.7 . 7 Figure 3.1 . 8 Copyright Electronic Industries Alliance Provi

27、ded by IHS under license with EIANot for ResaleNo reproduction or networking permitted without license from IHS-,-,- STD-EIA TIA-5bL-ENGL 1970 M 3234b00 Ob14570 121 EIA/TIA-561 Page i SECTION ONE 1. SCOPE 1.1 GENERAL This Standard is applicable to the interconnection of data terminating equipment (D

28、TE) and data circuit-terminating equipment (DCE) employing serial binary data interchange where a minimal number of control and information circuits are required. It defines: Section i - Scope Section 2 - Interface Mechanical Characteristics Section 3 - Functional Description of the Interchange Circ

29、uits The electrical characteristics applicable to this interface can be found in AMERICAN NATIONAL STANDARD ANSI/EIA/TIA-562. 1.2 CONNECTION When used in conjunction with the above mentioned electrical characteristics standard, this Standard applies where equipment on one side of the DTE/DCE interfa

30、ce is intended for connection directly to the other side without additional technical considerations. 1.3 BIT SEQUENCES This Standard applies to data communication systems where data is bit serialieed by the DTE and the DCE and places no restrictions on the arrangement or the sequence of bits. 1.4 D

31、ATA SIGNALING RATES This Standard is applicable for use at data signaling rates at or below 38.4 kbitfs. Equipments complying with this Standard, however, need not operate over this entire signaling range. They may be designed to operate over a more narrow range as appropriate for the specific appli

32、cation. 1.5 NON-SYNCHRONOUS COMMUNICATION This Standard applies to non-synchronous serial binary data communication systems. 1.6 CLASSES OF SERVICE This Standard applies to duplex switched, non-switched, dedicated, leased or private line service, either two-wire or four-wire. Copyright Electronic In

33、dustries Alliance Provided by IHS under license with EIANot for ResaleNo reproduction or networking permitted without license from IHS-,-,-EIA/TIAdBl Page 2 SECTION TWO 2. MTEBXACE MECHANICAL CHARACTERISTICS a.1 POINT OF INTERFACE The interface between the DTE and the DOE is located at a pluggable c

34、onnector signal interface point between the two equipments (see Figure 2.1). An hin-*0a Pig in these cases the ON condition on Circuit 125 may be in response to these predefmed ringing signals. The operation of this circuit shall not be disabled by an OFF condition on Circuit 108/2 (DTE Ready). The

35、DTE may decline to answer a call by not placing an ON condition on Circuit 108/2 in response to 125 cycling. Copyright Electronic Industries Alliance Provided by IHS under license with EIANot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STDSEIA TIA-SbL-ENGL 1970 323

36、4b00 ObL9bO1 837 m EIA/TIA-561 Page 12 Circuit ISS-Ready for Receiving Direction: To the DCE This circuit is used to control the transfer of data on Circuit 104 (Received Data) when an intermediate function such as error control is being used in the DCE. The ON condition on Circuit 133 indicates tha

37、t the DTE is capable of receiving data. The OFF condition indicates that the DTE is not capable of receiving data and causes the DCE, or the intermediate function, to retain the data. In some DCEs the OFF condition on Circuit 133 niay also cause a signal to be transmitted to the distant DCE causing

38、an OFF condition to be placed on Circuit 106 (Clear to Send) extending the flow control to the distant DTE. . Copyright Electronic Industries Alliance Provided by IHS under license with EIANot for ResaleNo reproduction or networking permitted without license from IHS-,-,-Copyright Electronic Industries Alliance Provided by IHS under license with EIANot for ResaleNo reproduction or networking permitted without license from IHS-,-,-