1、 TIA-1019-A September 2012Standard for Installation, Alteration and Maintenance of Antenna Supporting Structures and Antennas ANSI/TIA-1019-A-2012 APPROVED: AUGUST 16, 2012 REAFFIRMED: AUGUST 3, 2016 NOTICE TIA Engineering Standards and Publications are designed to serve the public interest through
2、eliminating misunderstandings between manufacturers and purchasers, facilitating interchangeability and improvement of products, and assisting the purchaser in selecting and obtaining with minimum delay the proper product for their particular need. The existence of such Standards and Publications sh
3、all not in any respect preclude any member or non-member of TIA from manufacturing or selling products not conforming to such Standards and Publications. Neither shall the existence of such Standards and Publications preclude their voluntary use by Non-TIA members, either domestically or internation
4、ally. Standards and Publications are adopted by TIA in accordance with the American National Standards Institute (ANSI) patent policy. By such action, TIA does not assume any liability to any patent owner, nor does it assume any obligation whatever to parties adopting the Standard or Publication. Th
5、is Standard does not purport to address all safety problems associated with its use or all applicable regulatory requirements. It is the responsibility of the user of this Standard to establish appropriate safety and health practices and to determine the applicability of regulatory limitations befor
6、e its use. Any use of trademarks in this document are for information purposes and do not constitute an endorsement by TIA or this committee of the products or services of the company. (From Project No. ANSI/TIA-PN-1019-A-RF1, formulated under the cognizance of the TIA TR-14 Committee on Structural
7、Standards for Communication and Small Wind Turbine Support Structures). Published by TELECOMMUNICATIONS INDUSTRY ASSOCIATION Standards and Technology Department 1320 N. Courthouse Road, Suite 200 Arlington, VA 22201 U.S.A. PRICE: Please refer to current Catalog of TIA TELECOMMUNICATIONS INDUSTRY ASS
8、OCIATION STANDARDS AND ENGINEERING PUBLICATIONS or call IHS, USA and Canada (1-877-413-5187) International (303-397-2896) or search online at http:/www.tiaonline.org/standards/catalog/ All rights reserved Printed in U.S.A. NOTICE OF COPYRIGHT This document is copyrighted by the TIA. Reproduction of
9、these documents either in hard copy or soft copy (including posting on the web) is prohibited without copyright permission. For copyright permission to reproduce portions of this document, please contact the TIA Standards Department or go to the TIA website (www.tiaonline.org) for details on how to
10、request permission. Details are located at: http:/www.tiaonline.org/standards/catalog/info.cfm#copyright or Telecommunications Industry Association Standards and Technology Department 1320 N. Courthouse Road, Suite 200 Arlington, VA 22201 USA +1.703.907.7700 Organizations may obtain permission to re
11、produce a limited number of copies by entering into a license agreement. For information, contact IHS 15 Inverness Way East Englewood, CO 80112-5704 or call USA and Canada (1.800.525.7052) International (303.790.0600) NOTICE OF DISCLAIMER AND LIMITATION OF LIABILITY The document to which this Notice
12、 is affixed (the “Document”) has been prepared by one or more Engineering Committees or Formulating Groups of the Telecommunications Industry Association (“TIA”). TIA is not the author of the Document contents, but publishes and claims copyright to the Document pursuant to licenses and permission gr
13、anted by the authors of the contents. TIA Engineering Committees and Formulating Groups are expected to conduct their affairs in accordance with the TIA Procedures for American National Standards and TIA Engineering Committee Operating Procedures, the current and predecessor versions of which are av
14、ailable at http:/www.tiaonline.org/standards/ec-procedures)/TIAs function is to administer the process, but not the content, of document preparation in accordance with the Manual and, when appropriate, the policies and procedures of the American National Standards Institute (“ANSI”). TIA does not ev
15、aluate, test, verify or investigate the information, accuracy, soundness, or credibility of the contents of the Document. In publishing the Document, TIA disclaims any undertaking to perform any duty owed to or for anyone. If the Document is identified or marked as a project number (PN) document, or
16、 as a standards proposal (SP) document, persons or parties reading or in any way interested in the Document are cautioned that: (a) the Document is a proposal; (b) there is no assurance that the Document will be approved by any Committee of TIA or any other body in its present or any other form; (c)
17、 the Document may be amended, modified or changed in the standards development or any editing process. The use or practice of contents of this Document may involve the use of intellectual property rights (“IPR”), including pending or issued patents, or copyrights, owned by one or more parties. TIA m
18、akes no search or investigation for IPR. When IPR consisting of patents and published pending patent applications are claimed and called to TIAs attention, a statement from the holder thereof is requested, all in accordance with the Manual. TIA takes no position with reference to, and disclaims any
19、obligation to investigate or inquire into, the scope or validity of any claims of IPR. TIA will neither be a party to discussions of any licensing terms or conditions, which are instead left to the parties involved, nor will TIA opine or judge whether proposed licensing terms or conditions are reaso
20、nable or non-discriminatory. TIA does not warrant or represent that procedures or practices suggested or provided in the Manual have been complied with as respects the Document or its contents. If the Document contains one or more Normative References to a document published by another organization
21、(“other SSO”) engaged in the formulation, development or publication of standards (whether designated as a standard, specification, recommendation or otherwise), whether such reference consists of mandatory, alternate or optional elements (as defined in the TIA Procedures for American National Stand
22、ards) then (i) TIA disclaims any duty or obligation to search or investigate the records of any other SSO for IPR or letters of assurance relating to any such Normative Reference; (ii) TIAs policy of encouragement of voluntary disclosure (see TIA Procedures for American National Standards Annex C.1.
23、2.3) of Essential Patent(s) and published pending patent applications shall apply; and (iii) Information as to claims of IPR in the records or publications of the other SSO shall not constitute identification to TIA of a claim of Essential Patent(s) or published pending patent applications. TIA does
24、 not enforce or monitor compliance with the contents of the Document. TIA does not certify, inspect, test or otherwise investigate products, designs or services or any claims of compliance with the contents of the Document. ALL WARRANTIES, EXPRESS OR IMPLIED, ARE DISCLAIMED, INCLUDING WITHOUT LIMITA
25、TION, ANY AND ALL WARRANTIES CONCERNING THE ACCURACY OF THE CONTENTS, ITS FITNESS OR APPROPRIATENESS FOR A PARTICULAR PURPOSE OR USE, ITS MERCHANTABILITY AND ITS NONINFRINGEMENT OF ANY THIRD PARTYS INTELLECTUAL PROPERTY RIGHTS. TIA EXPRESSLY DISCLAIMS ANY AND ALL RESPONSIBILITIES FOR THE ACCURACY OF
26、 THE CONTENTS AND MAKES NO REPRESENTATIONS OR WARRANTIES REGARDING THE CONTENTS COMPLIANCE WITH ANY APPLICABLE STATUTE, RULE OR REGULATION, OR THE SAFETY OR HEALTH EFFECTS OF THE CONTENTS OR ANY PRODUCT OR SERVICE REFERRED TO IN THE DOCUMENT OR PRODUCED OR RENDERED TO COMPLY WITH THE CONTENTS. TIA S
27、HALL NOT BE LIABLE FOR ANY AND ALL DAMAGES, DIRECT OR INDIRECT, ARISING FROM OR RELATING TO ANY USE OF THE CONTENTS CONTAINED HEREIN, INCLUDING WITHOUT LIMITATION ANY AND ALL INDIRECT, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES (INCLUDING DAMAGES FOR LOSS OF BUSINESS, LOSS OF PROFITS, LITIGATION,
28、OR THE LIKE), WHETHER BASED UPON BREACH OF CONTRACT, BREACH OF WARRANTY, TORT (INCLUDING NEGLIGENCE), PRODUCT LIABILITY OR OTHERWISE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. THE FOREGOING NEGATION OF DAMAGES IS A FUNDAMENTAL ELEMENT OF THE USE OF THE CONTENTS HEREOF, AND THESE CONTENTS W
29、OULD NOT BE PUBLISHED BY TIA WITHOUT SUCH LIMITATIONS. ANSI/TIA-1019-A 1 Standard for Installation, Alteration and Maintenance of Antenna Supporting Structures and Antennas HISTORY 3 OBJECTIVE 3 SCOPE 3 1. GENERAL 4 1.1. Definitions 4 1.2. Abbreviations 8 1.3. Symbols and Notations 8 2. CONSTRUCTION
30、 CONSIDERATIONS 11 2.1. Scope 11 2.2. Rigging Plans 11 2.3. Construction Equipment 11 2.4. Lifting Devices 12 2.5. Gin Pole Jumping and Lifting 13 2.6. Hoist 13 2.7. Temporary Supports 14 2.8. Guy Installation 15 2.9. Rigging Components 16 2.10. Personnel Lifting 18 2.11. Dismantling/Modification Co
31、nsiderations 18 2.12. Load Testing and Verification 19 2.13. Monitoring During Lifting Operations 19 2.14. Climbing Facilities 19 2.15. Site Evaluation 20 2.16. Training 20 3. GIN POLE OPERATION AND USE 27 3.1. Scope 27 3.2. Gin Pole Components 27 3.3. Lifting Personnel 28 3.4. Gin Pole Inspections
32、28 3.5. Load Charts 29 ANSI/TIA-1019-A 2 3.6. Tilted Gin Poles 32 3.7. Special Engineered Lifts 33 4. SUPPORTING STRUCTURE LOADING 44 4.1. Scope 44 4.2. Design Standards 44 4.3. Structural Loads 44 4.4. Load Combinations 45 4.5. Construction Duration Reduction Factors 45 5. GIN POLE ANALYSIS AND DES
33、IGN 47 5.1. Scope 47 5.2. Classification of Vertical or Near Vertical Gin Poles 47 5.3. Design Method 47 5.4. Impact Factors 47 5.5. Load Combinations 47 5.6. Reactions 48 5.7. Analysis Models 48 5.8. Overall Stability 49 5.9. Connections 50 5.10. Rooster Head 51 5.11. Generation of Standard Load Ch
34、arts for Vertical or Near Vertical Gin Poles 52 6. GIN POLE CONSTRUCTION 57 6.1. Scope 57 6.2. Manufacturing 57 ANNEX A: PROCUREMENT AND USER GUIDELINES (NORMATIVE) 59 ANNEX B: GIN POLE ENGINEERING DESIGN (NORMATIVE) 60 ANNEX C: EVALUATION OF EXISTING GIN POLES (NORMATIVE) 63 ANNEX D: RIGGING PLAN (
35、NORMATIVE) 64 ANNEX E: WIRE ROPE END CONNECTIONS (NORMATIVE) 72 ANNEX F: EVALUATION OF A COMMUNICATION TOWER SITE (NORMATIVE) 77 ANNEX G: REFERENCES (INFORMATIVE) 82 Notes: 1. Normative annexes are integral parts of the Standard which for reasons of convenience are placed after other requirements of
36、 the Standard. 2. Informative annexes contain additional information and are not considered parts of the Standard. ANSI/TIA-1019-A 3 HISTORY The installation, alteration and maintenance of communications structures, and the associated equipment they support have been based on extensive field practic
37、es that are unique due to their height and slenderness and historically have been performed without the benefit of a uniform design standard. OBJECTIVE The objective of this Standard is to provide construction guidelines for the Telecommunications and Broadcast Industries. This Standard is intended
38、to replace the Standard ANSI/TIA-1019-2004, “Structural Standards for Steel Gin Poles Used for Installation of Antenna Towers and Antenna Supporting Structures”. Information contained in this Standard was obtained from available sources and represents, in the judgment of the subcommittee, the accept
39、ed Industry minimum standard for the installation, alteration and maintenance of antenna supporting structures and antennas. While it is believed to be accurate, this information should not be relied upon for a specific application without competent professional examination and verification of its a
40、ccuracy, suitability, and applicability. It is the intent of this Standard to have Owners specify this Standard for projects and to have Contractors follow the Standard in their work. SCOPE The scope of this Standard is to provide construction considerations and loading requirements for structures u
41、nder construction related to antenna supporting structures and antennas. The Standard addresses the requirements for specialized equipment such as: gin poles, hoists and required temporary supports. This Standard provides criteria based upon both Load and Resistance Factor Design (LRFD) and Allowabl
42、e Stress Design (ASD) methods. Figures and drawings in this Standard are for illustration purposes only and are not intended to represent all potential aspects of a particular lift or rigging situation. It is the responsibility of the user to determine an appropriate rigging plan in accordance with
43、this Standard for construction activities accounting for all loads, forces and reactions. ANSI/TIA-1019-A 4 1. GENERAL 1.1. Definitions Allowable Stress Design: a design method utilizing working loads where the design strength of a structural component is equal to its minimum ultimate strength divid
44、ed by a safety factor. Basket: the lower support of a gin pole providing both vertical and horizontal support. Boatswain Chair: a seat consisting of a rigid or flexible seat and a rope, originally used on ships and boats and later adapted for working at heights on buildings and other structures. Bri
45、dle: (Collar) the upper support of a gin pole providing horizontal support. Capstan Hoist: a spool shaped drum for wrapping a synthetic rope to raise or lower a load. Charted Value: a value tabulated in a gin pole Standard Load Chart. Communication Structure: a structure used for transmitting or rec
46、eiving electronic communication or broadcast signals. Competent Rigger: a person knowledgeable and experienced with the procedures and equipment common to the Communication Structures Industry and trained to identify hazards with authorization to take prompt corrective measures. Construction: field
47、activities related to the installation, alteration or maintenance of antenna supporting structures and antennas. Construction Duration: the period of time a structure is subject to construction loading. Construction Loads: loads applied to a structure by rigging systems, loads being lifted, and all
48、other material, equipment or loading associated with construction. Crown Block: (Top Block) the upper sheave assembly attached to a structure used to change the direction of a load or jump line coming from a hoist. Dismantling: the removal of existing antennas, appurtenances, structural components o
49、r the structure itself. Effective Length Factor: a factor to modify the unbraced length of a structural component based on its structural configuration and end conditions. Effective Wind Speed: the design wind speed used to determine wind loading. Fleet Angle: the wire rope deviation angle from a line normal (perpendicular) to the pin axis of a sheave or block. Free Body Diagram: a representation of an object in equilibrium, showing external forces, moments and support reactions. Full Body Harness with Boatswain Seat: a full body harness that incorporates a rigi
copyright@ 2008-2019 麦多课文库（www.mydoc123.com）网站版权所有
备案/许可证编号：苏ICP备17064731号-1