ANSI TIA-102.CCAB-A-2014 Project 25 Two - Slot Time Division Multiple Access Transceiver Performance Recommendations.pdf

1、 TIA-102.CCAB-A (Revision of TIA-102.CCAB) March 2014Project 25 Two - Slot Time Division Multiple Access Transceiver Performance RecommendationsANSI/TIA-102.CCAB-A-2014 APPROVED: MARCH 17, 2014 NOTICE TIA Engineering Standards and Publications are designed to serve the public interest through elimin

2、ating misunderstandings between manufacturers and purchasers, facilitating interchangeability and improvement of products, and assisting the purchaser in selecting and obtaining with minimum delay the proper product for their particular need. The existence of such Standards and Publications shall no

3、t in any respect preclude any member or non-member of TIA from manufacturing or selling products not conforming to such Standards and Publications. Neither shall the existence of such Standards and Publications preclude their voluntary use by Non-TIA members, either domestically or internationally.

4、Standards and Publications are adopted by TIA in accordance with the American National Standards Institute (ANSI) patent policy. By such action, TIA does not assume any liability to any patent owner, nor does it assume any obligation whatever to parties adopting the Standard or Publication. This Sta

5、ndard does not purport to address all safety problems associated with its use or all applicable regulatory requirements. It is the responsibility of the user of this Standard to establish appropriate safety and health practices and to determine the applicability of regulatory limitations before its

6、use. Any use of trademarks in this document are for information purposes and do not constitute an endorsement by TIA or this committee of the products or services of the company. (From Project No. ANSI/TIA-PN-102.CCAB-A, formulated under the cognizance of the TIA TR-8 Mobile and Personal Private Rad

7、io TR-8.6 Subcommittee on Equipment Performance Recommendation). Published by TELECOMMUNICATIONS INDUSTRY ASSOCIATION Technology (b) there is no assurance that the Document will be approved by any Committee of TIA or any other body in its present or any other form; (c) the Document may be amended, m

8、odified or changed in the standards development or any editing process. The use or practice of contents of this Document may involve the use of intellectual property rights (“IPR”), including pending or issued patents, or copyrights, owned by one or more parties. TIA makes no search or investigation

9、 for IPR. When IPR consisting of patents and published pending patent applications are claimed and called to TIAs attention, a statement from the holder thereof is requested, all in accordance with the Manual. TIA takes no position with reference to, and disclaims any obligation to investigate or in

10、quire into, the scope or validity of any claims of IPR. TIA will neither be a party to discussions of any licensing terms or conditions, which are instead left to the parties involved, nor will TIA opine or judge whether proposed licensing terms or conditions are reasonable or non-discriminatory. TI

11、A does not warrant or represent that procedures or practices suggested or provided in the Manual have been complied with as respects the Document or its contents. If the Document contains one or more Normative References to a document published by another organization (“other SSO”) engaged in the fo

12、rmulation, development or publication of standards (whether designated as a standard, specification, recommendation or otherwise), whether such reference consists of mandatory, alternate or optional elements (as defined in the TIA Engineering Manual, 4thedition) then (i) TIA disclaims any duty or ob

13、ligation to search or investigate the records of any other SSO for IPR or letters of assurance relating to any such Normative Reference; (ii) TIAs policy of encouragement of voluntary disclosure (see Engineering Manual Section 6.5.1) of Essential Patent(s) and published pending patent applications s

14、hall apply; and (iii) Information as to claims of IPR in the records or publications of the other SSO shall not constitute identification to TIA of a claim of Essential Patent(s) or published pending patent applications. TIA does not enforce or monitor compliance with the contents of the Document. T

15、IA does not certify, inspect, test or otherwise investigate products, designs or services or any claims of compliance with the contents of the Document. ALL WARRANTIES, EXPRESS OR IMPLIED, ARE DISCLAIMED, INCLUDING WITHOUT LIMITATION, ANY AND ALL WARRANTIES CONCERNING THE ACCURACY OF THE CONTENTS, I

16、TS FITNESS OR APPROPRIATENESS FOR A PARTICULAR PURPOSE OR USE, ITS MERCHANTABILITY AND ITS NONINFRINGEMENT OF ANY THIRD PARTYS INTELLECTUAL PROPERTY RIGHTS. TIA EXPRESSLY DISCLAIMS ANY AND ALL RESPONSIBILITIES FOR THE ACCURACY OF THE CONTENTS AND MAKES NO REPRESENTATIONS OR WARRANTIES REGARDING THE

17、CONTENTS COMPLIANCE WITH ANY APPLICABLE STATUTE, RULE OR REGULATION, OR THE SAFETY OR HEALTH EFFECTS OF THE CONTENTS OR ANY PRODUCT OR SERVICE REFERRED TO IN THE DOCUMENT OR PRODUCED OR RENDERED TO COMPLY WITH THE CONTENTS. TIA SHALL NOT BE LIABLE FOR ANY AND ALL DAMAGES, DIRECT OR INDIRECT, ARISING

18、 FROM OR RELATING TO ANY USE OF THE CONTENTS CONTAINED HEREIN, INCLUDING WITHOUT LIMITATION ANY AND ALL INDIRECT, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES (INCLUDING DAMAGES FOR LOSS OF BUSINESS, LOSS OF PROFITS, LITIGATION, OR THE LIKE), WHETHER BASED UPON BREACH OF CONTRACT, BREACH OF WARRANTY

19、, TORT (INCLUDING NEGLIGENCE), PRODUCT LIABILITY OR OTHERWISE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. THE FOREGOING NEGATION OF DAMAGES IS A FUNDAMENTAL ELEMENT OF THE USE OF THE CONTENTS HEREOF, AND THESE CONTENTS WOULD NOT BE PUBLISHED BY TIA WITHOUT SUCH LIMITATIONS. ANSI/TIA-PN-102.

20、CCAB-A i FOREWORD (This foreword is not part of this Standard) This Standard was developed and will be maintained by the TR-8.6 Equipment Performance Recommendations Subcommittee of the TR-8 Land Mobile Services Committee. Participating in its development were radio equipment and test equipment manu

21、facturers as well as representatives of public safety user groups from the Association of Public Safety Communications Officials, International (APCO), the National Association of State Telecommunications Directors (NASTD), and numerous federal government agencies. This standard provides the standar

22、d limit values for the equipment characteristics assessed by the measurement methods described in TIA-102.CCAA-A, Two-Slot Time Division Multiple Access Transceiver Measurement Methods. This Standard was approved for publication during the “to be determined” meeting of Subcommittee TR 8.6. There are

23、 two annexes in this Standard, The annexes, A and B, are informative and are not considered part of this Standard. ANSI/TIA-PN-102.CCAB-A ii Blank Page ANSI/TIA-PN-102.CCAB-A iii Table of Contents 1 Introduction . 1 1.1 Scope . 1 1.2 Object 1 1.3 Standard Definitions . 1 1.4 Standard Test Conditions

24、 . 1 1.5 Characteristics of Test Equipment 1 1.6 Normative Reference Documents 1 1.7 Revision History . 2 2 Methods of Measurements . 2 3 Standards for all equipment . 2 3.1 Receiver Section 4 3.1.1 Radiated spurious emissions 4 3.1.2 Conducted spurious output power . 4 3.1.3 Power line conducted sp

25、urious output voltage 4 3.1.4 Reference sensitivity . 5 3.1.5 Faded reference sensitivity . 5 3.1.6 Signal delay spread capability . 5 3.1.7 Adjacent channel rejection 6 3.1.8 Co-channel rejection . 6 3.1.9 Spurious response rejection 6 3.1.10 Intermodulation rejection . 7 3.1.11 Signal displacement

26、 bandwidth . 7 3.1.12 Audio output distortion 7 3.1.13 Residual audio noise ratio . 7 3.1.14 Average radiation sensitivity 8 3.1.15 Acoustic audio output 8 3.1.16 Bit error rate floor 8 3.1.17 Blocking rejection 8 3.2 Transmitter section 10 3.2.1 RF Output power 10 3.2.2 Operating frequency accuracy

27、 .10 3.2.3 Electrical audio performance 11 3.2.4 Acoustic audio performance .11 3.2.5 Modulation emission spectrum .11 3.2.6 Unwanted emissions: radiated spurious .12 3.2.7 Unwanted emissions: conducted spurious .13 3.2.8 Unwanted emissions: adjacent channel power ratio .13 3.2.9 Intermodulation att

28、enuation 14 3.2.10 Average radiated power output 15 3.2.11 Conducted spurious emissions into VSWR 16 3.2.12 Frequency deviation for H-CPM .16 3.2.13 Modulation fidelity 16 3.2.14 Symbol rate accuracy .16 ANSI/TIA-PN-102.CCAB-A iv 3.2.15 H-CPM Transmitter logical channel peak adjacent channel power r

29、atio . 16 3.2.16 H-CPM Transmitter logical channel off slot power 17 3.2.17 H-CPM Transmitter logical channel power envelope 17 3.2.18 H-CPM Transmitter logical channel time alignment 17 3.3 Trunked system timing characteristics 18 3.3.1 Trunking voice access time 18 3.4 Unit characteristics 19 3.4.

30、1 Power supply voltage range . 19 3.4.2 Temperature range 21 3.4.3 High humidity . 22 3.4.4 Vibration stability 23 3.4.5 Shock stability 23 3.4.6 DC Supply noise susceptibility . 24 3.4.7 Battery life 24 3.4.8 Dimensions 25 3.4.9 Weight . 25 3.4.10 Other environmental 25 ANNEX A Measurement Uncertai

31、nty (Informative) . 29 A.1 Introduction . 29 A.2 Definitions . 29 A.2.1 Accuracy 29 A.2.2 Measurand . 29 A.2.3 Error 29 A.2.4 Bias and systematic error 29 A.2.5 Random error. 30 A.2.6 RSS errors . 30 A.2.7 Precision 30 A.2.8 Uncertainty 30 A.2.9 Confidence limits . 30 A.3 Principles for calculating

32、measurement uncertainties 30 A.3.1 General 30 A.3.2 Types of errors . 30 A.3.3 Propagation of errors . 33 A.3.4 Converting power errors expressed in dB to percentage 34 A.3.5 Mismatch uncertainty and mismatch loss . 34 A.3.6 Sensitivity of transmitter output to load 35 A.3.7 Correcting rms measureme

33、nts for the effects of rms residuals . 36 A.3.8 Correcting peak measurements for the effects of residuals 37 ANNEX B Example calculations (Informative) 38 B.1 Example calculations for receiver measurements 38 B.1.1 Radiated spurious emissions . 38 B.1.2 Conducted spurious output power 38 B.1.3 Power

34、 line conducted spurious output voltage . 38 B.1.4 Reference sensitivity 39 B.1.5 Faded reference sensitivity 39 B.1.6 Signal delay spread capability 39 ANSI/TIA-PN-102.CCAB-A v B.1.7 Adjacent channel rejection .40 B.1.8 Co-channel rejection 40 B.1.9 Spurious response rejection .40 B.1.10 Intermodul

35、ation rejection 41 B.1.11 Signal displacement bandwidth 41 B.1.12 Audio output distortion .41 B.1.13 Residual audio noise ratio 42 B.1.14 Average radiation sensitivity .42 B.1.15 Acoustic audio output .42 B.1.16 Bit error rate floor .42 B.1.17 Blocking rejection .43 B.2 Example calculations for tran

36、smitter measurements 44 B.2.1 RF Output power 44 B.2.2 Operating frequency accuracy .44 B.2.3 Electrical audio performance 45 B.2.4 Acoustic audio performance .45 B.2.5 Modulation emission spectrum .45 B.2.6 Unwanted emissions: radiated spurious .45 B.2.7 Unwanted emissions: conducted spurious .46 B

37、.2.8 Unwanted emissions: adjacent channel power ratio .46 B.2.9 Intermodulation attenuation 47 B.2.10 Average radiated power output 48 B.2.11 Conducted spurious emissions into VSWR 48 B.2.12 Frequency deviation for H-CPM .48 B.2.13 Modulation fidelity 48 B.2.14 Symbol rate accuracy .49 B.2.15 H-CPM

38、Transmitter logical channel peak adjacent channel power ratio .49 B.2.16 H-CPM Transmitter logical channel off slot power 49 B.2.17 H-CPM Transmitter logical channel power envelope 50 B.2.18 H-CPM Transmitter logical channel time alignment 50 B.3 Trunking system measurements .51 B.3.1 Trunking voice

39、 access time 51 ANSI/TIA-PN-102.CCAB-A vi Patent Identification NOTE: The users attention is called to the possibility that compliance with this document may require use of one or more inventions covered by patent rights. By publication of this TIA Publication, no position is taken with respect to t

40、he validity of those claims of rights or of any patent rights in connection with this document. The patent holder(s) so far identified to TIA have, however, filed statements of willingness to grant licenses under those rights either without compensation or on reasonable and nondiscriminatory terms a

41、nd conditions to applicants desiring to obtain such licenses for the purpose of implementing this TIA Publication. Details regarding the filed statements may be obtained from the TIA. The following patent holder and patent has been identified in accordance with the TIA intellectual property rights p

42、olicy: No patents have been identified. TIA shall not be responsible for identifying patents for which licenses may be required in connection with any TIA Publication or for conducting inquiries into the legal validity or scope of those patents that are brought to its attention. ANSI/TIA-PN-102.CCAB

43、-A 1 1 Introduction 1.1 Scope This Standard provides physical layer performance standards under standard conditions for 12.5 kHz channelization digitally modulated radio equipment used in the Private (Dispatch) Land Mobile Services that employs a Two-Slot Time Division Multiple Access method for tra

44、nsmission and reception of voice or data using digital techniques, with or without encryption, with a frequency of 1 GHz or less. The definition and description of the system in which this equipment operates is given in the Project 25 Two-Slot TDMA Overview document (TIA TSB-102.BBAA). The physical

45、layer description is given in Project 25 Phase 2 Two-Slot Time Division Multiple Access Physical Layer Description (TIA-102.BBAB). The media access control is given in Project 25 Phase 2, Two-Slot Time Division Multiple Access Media Access Control Layer Specification- Trunked Voice Services, (TIA-10

46、2.BBAC). Two performance levels have been distinguished herein for certain equipment characteristics. The performance level of Class B is comparable to the performance level for 12.5 kHz analog radio equipment in TIA/EIA-603-D, Land Mobile FM or PM Communications Equipment. Class A describes a highe

47、r level of performance for more stringent applications. Should Federal Communications Commission (FCC) requirements as listed in 47 CFR, Code of Federal Regulations, Telecommunication, become more stringent than any standard contained herein, the FCC requirements supersede these. The standards in th

48、is document may be applicable to applications other than those specifically addressed in Project 25. Use of these standards is encouraged for any application of similar equipment; however, the user should review the required standards needed for the specific application. 1.2 Object The objective of

49、this document is to serve as a performance level benchmark for assessment of equipment per the measurement methods defined in companion document TIA-102.CCAA-A, Two-Slot Time Division Multiple Access Transceiver Measurement Methods. 1.3 Standard Definitions These are described in TIA-102.CCAA-A, clause 1.5. 1.4 Standard Test Conditions These are described in TIA-102.CCAA-A, clause 1.7. 1.5 Characteristics of Test Equipment These are described in IA-102.CCAA-A, clause 1.8. 1.6 Normative Reference Documents The following Standards contain provisions that, through reference in this text,