ANSI TIA-1062-2006 Telecommunications Telephony Aspects of MLTS and Packetbased Equipment including VoIP Interface Requirements for Packet-based Gateways《分组网关的1544 kbps速率接口要求》.pdf

1、 TIA-1062 April 2006 Telecommunications Telephony Aspects of MLTS and Packetbased Equipment, including VoIP Interface Requirements for Packet-based Gateways ANSI/TIA-1062 - 2006 APPROVED: APRIL 6, 2006 REAFFIRMED: OCTOBER 17, 2011 NOTICE TIA Engineering Standards and Publications are designed to ser

2、ve the public interest through eliminating misunderstandings between manufacturers and purchasers, facilitating interchangeability and improvement of products, and assisting the purchaser in selecting and obtaining with minimum delay the proper product for their particular need. The existence of suc

3、h Standards and Publications shall not in any respect preclude any member or non-member of TIA from manufacturing or selling products not conforming to such Standards and Publications. Neither shall the existence of such Standards and Publications preclude their voluntary use by Non-TIA members, eit

4、her domestically or internationally. Standards and Publications are adopted by TIA in accordance with the American National Standards Institute (ANSI) patent policy. By such action, TIA does not assume any liability to any patent owner, nor does it assume any obligation whatever to parties adopting

5、the Standard or Publication. This Standard does not purport to address all safety problems associated with its use or all applicable regulatory requirements. It is the responsibility of the user of this Standard to establish appropriate safety and health practices and to determine the applicability

6、of regulatory limitations before its use. (From Standards Proposal No. 3-0190, formulated under the cognizance of the TIA TR-41.1, Subcommittee on Telephony Aspects of MLTS and VoIP Equipment). Published by TELECOMMUNICATIONS INDUSTRY ASSOCIATION Standards and Technology Department 2500 Wilson Boule

7、vard Arlington, VA 22201 U.S.A. PRICE: Please refer to current Catalog of TIA TELECOMMUNICATIONS INDUSTRY ASSOCIATION STANDARDS AND ENGINEERING PUBLICATIONS or call IHS, USA and Canada (1-877-413-5187) International (303-397-2896) or search online at http:/www.tiaonline.org/standards/catalog/ All ri

8、ghts reserved Printed in U.S.A. NOTICE OF COPYRIGHT This document is copyrighted by the TIA. Reproduction of these documents either in hard copy or soft copy (including posting on the web) is prohibited without copyright permission. For copyright permission to reproduce portions of this document, pl

9、ease contact the TIA Standards Department or go to the TIA website (www.tiaonline.org) for details on how to request permission. Details are located at: http:/www.tiaonline.org/standards/catalog/info.cfm#copyright or Telecommunications Industry Association Technology (b) there is no assurance that t

10、he Document will be approved by any Committee of TIA or any other body in its present or any other form; (c) the Document may be amended, modified or changed in the standards development or any editing process. The use or practice of contents of this Document may involve the use of intellectual prop

11、erty rights (“IPR”), including pending or issued patents, or copyrights, owned by one or more parties. TIA makes no search or investigation for IPR. When IPR consisting of patents and published pending patent applications are claimed and called to TIAs attention, a statement from the holder thereof

12、is requested, all in accordance with the Manual. TIA takes no position with reference to, and disclaims any obligation to investigate or inquire into, the scope or validity of any claims of IPR. TIA will neither be a party to discussions of any licensing terms or conditions, which are instead left t

13、o the parties involved, nor will TIA opine or judge whether proposed licensing terms or conditions are reasonable or non-discriminatory. TIA does not warrant or represent that procedures or practices suggested or provided in the Manual have been complied with as respects the Document or its contents

14、. If the Document contains one or more Normative References to a document published by another organization (“other SSO”) engaged in the formulation, development or publication of standards (whether designated as a standard, specification, recommendation or otherwise), whether such reference consist

15、s of mandatory, alternate or optional elements (as defined in the TIA Engineering Manual, 4thedition) then (i) TIA disclaims any duty or obligation to search or investigate the records of any other SSO for IPR or letters of assurance relating to any such Normative Reference; (ii) TIAs policy of enco

16、uragement of voluntary disclosure (see Engineering Manual Section 6.5.1) of Essential Patent(s) and published pending patent applications shall apply; and (iii) Information as to claims of IPR in the records or publications of the other SSO shall not constitute identification to TIA of a claim of Es

17、sential Patent(s) or published pending patent applications. TIA does not enforce or monitor compliance with the contents of the Document. TIA does not certify, inspect, test or otherwise investigate products, designs or services or any claims of compliance with the contents of the Document. ALL WARR

18、ANTIES, EXPRESS OR IMPLIED, ARE DISCLAIMED, INCLUDING WITHOUT LIMITATION, ANY AND ALL WARRANTIES CONCERNING THE ACCURACY OF THE CONTENTS, ITS FITNESS OR APPROPRIATENESS FOR A PARTICULAR PURPOSE OR USE, ITS MERCHANTABILITY AND ITS NONINFRINGEMENT OF ANY THIRD PARTYS INTELLECTUAL PROPERTY RIGHTS. TIA

19、EXPRESSLY DISCLAIMS ANY AND ALL RESPONSIBILITIES FOR THE ACCURACY OF THE CONTENTS AND MAKES NO REPRESENTATIONS OR WARRANTIES REGARDING THE CONTENTS COMPLIANCE WITH ANY APPLICABLE STATUTE, RULE OR REGULATION, OR THE SAFETY OR HEALTH EFFECTS OF THE CONTENTS OR ANY PRODUCT OR SERVICE REFERRED TO IN THE

20、 DOCUMENT OR PRODUCED OR RENDERED TO COMPLY WITH THE CONTENTS. TIA SHALL NOT BE LIABLE FOR ANY AND ALL DAMAGES, DIRECT OR INDIRECT, ARISING FROM OR RELATING TO ANY USE OF THE CONTENTS CONTAINED HEREIN, INCLUDING WITHOUT LIMITATION ANY AND ALL INDIRECT, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES (I

21、NCLUDING DAMAGES FOR LOSS OF BUSINESS, LOSS OF PROFITS, LITIGATION, OR THE LIKE), WHETHER BASED UPON BREACH OF CONTRACT, BREACH OF WARRANTY, TORT (INCLUDING NEGLIGENCE), PRODUCT LIABILITY OR OTHERWISE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. THE FOREGOING NEGATION OF DAMAGES IS A FUNDAME

22、NTAL ELEMENT OF THE USE OF THE CONTENTS HEREOF, AND THESE CONTENTS WOULD NOT BE PUBLISHED BY TIA WITHOUT SUCH LIMITATIONS. TIA-1062 Page 1 TABLE OF CONTENTS FOREWORD. 3 1 INTRODUCTION. 4 1.1 Purpose 4 1.2 Categories of Performance Criteria. 4 2 SCOPE 5 2.1 Conformance with Regulatory and Safety Stan

23、dards 5 3 NORMATIVE and INFORMATIVE REFERENCES 6 4 DEFINITIONS, ABBREVIATIONS and ACRONYMS 8 4.1 Definitions. 8 4.2 Abbreviations and Acronyms 10 5 DS1 and DSX-1 NETWORK INTERFACE REQUIREMENTS . 12 5.1 Electrical and Physical Characteristics 12 5.2 Electrical Interfaces.13 5.3 Signal Formats. 22 5.4

24、 ISDN Primary Rate Access (DSS1) Requirements . 39 5.5 ISDN Private Network Signaling (PSS1 / QSIG) Requirements 39 5.6 Channel-associated Signaling and Supervision Requirements 41 6 TRANSMISSION REQUIREMENTS 45 6.1 General 45 6.2 Echo Cancellation 45 7 DTMF SIGNALING REQUIREMENTS . 46 7.1 General 4

25、6 7.2 DTMF Generator Characteristics 47 7.3 DTMF Receiver Characteristics 48 8 CALL PROGRESS SIGNALING. 50 8.1 Call Progress Signals Sent to the VoIP networks 50 8.2 Definitions of Call Progress Signals 53 8.3 Electrical Standards for Call Progress Signals 54 Annex A. Bibliography 56 LIST OF FIGURES

26、 Figure 1 - Packet-based Gateway 1544 kbps Interface Connections12 Figure 2 - DSX-1 Cross-Connect Isolated Pulse Template 14 Figure 3 - DS1 Packet-based Gateway Interface Isolated Pulse Template.16 Figure 4 - Pulse Amplitude Envelope with 60 Hz Longitudinal Currents17 Figure 5 - Frequency Weighting

27、Function for Band 1 Jitter Specification.20 Figure 6 - Frequency Weighting Function for Band 2 Jitter Specification.20 Figure 7 - Example of Bipolar Eight Zero Substitution (B8ZS).21 Figure 8 - 1544 kbps Signal Format22 Figure 9 - Extended Superframe Framing (ESF) F-Bit Assignments .24 Figure 10 - E

28、SF/CMB Relationship25 Figure 11 - Mathematical Check-Bit Generation25 Figure 12 - Performance Report Message Structure.30 TIA-1062 Page 2 Figure 13 - QSIG Protocol Model.40 LIST OF TABLES Table 1 - Assigned Bit-patterned ESF Data Link Messages.32 Table 2 - Unassigned ESF Data Link Codewords 33 Table

29、 3 - Example - ESF Data Link Performance Report Messages34 Table 4 - Interface Type and Channel Unit Equivalent 42 Table 5 - Standard Call Progress Signals51 Table 6 - Other Call Progress Signals.52 TIA-1062 Page 3 FOREWORD (This foreword is not part of this standard.) This document is a TIA Telecom

30、munications Standard produced by TIA Engineering Technical Subcommittee TR-41.1 of Committee TR-41. This standard was developed in accordance with TIA procedural guidelines, and represents the consensus position of the subcommittee TR-41.1, which served as the formulating group. The TR-41.1 Engineer

31、ing Technical Subcommittee acknowledges the contribution made by the following individuals in the development of this standard. Name Representing Trone Bishop Verizon Robert Chrostowski Iwatsu Richard Frank Dietrich Lockard Group Kirit Patel Cisco Systems Joachim Pomy Avaya Vice-chair Tailey Tung Si

32、emens Communications, Inc. Chair i.e., equipment designed for operation with DS1 facility losses of up to 6 dB at 772 kHz. For example, using 22 gauge ABAM type cable, which has a loss of 6 dB at 772 kHz for 200 meters (655 feet), the distance between the DSX-1 interface in the packet-based gateway

33、and a cross-connect point can be up to 200 meters (655 feet). The distance from the cross-connect point to the DSX-1 interface in an NCTE for this example can also be up to 200 meters (655 feet). Thus, a maximum separation (based on DSX-1 connectivity) of 400 meters (1310 feet) is possible in this e

34、xample. TIA-1062 Page 14 Time in Unit Intervals-0.500.511.5-1 -0.5 0 0.5 1 1.5Normalized AmplitudeMaximumcurveMinimumcurveNote: 1 Unit Interval = 648 nanoseconds DSX-1 Pulse Template Corner Points Minimum Curve Maximum Curve Time (Unit Intervals) Normalized Amplitude Time (Unit Intervals) Normalized

35、 Amplitude -0.77 -0.05 -0.77 0.05 -0.23 -0.05 -0.39 0.05-0.23 0.50 -0.27 0.80 -0.15 0.95 -0.27 1.150.00 0.95 -0.12 1.15 0.15 0.90 0.00 1.050.23 0.50 0.27 1.05 0.23 -0.45 0.35 -0.070.46 -0.45 0.93 0.05 0.66 -0.20 1.16 0.050.93 -0.05 1.16 -0.05 Successive corner points are joined by straight lines to

36、form the template shown above Figure 2 - DSX-1 Cross-Connect Isolated Pulse Template TIA-1062 Page 15 5.2.2 DS1 Electrical Interface The electrical specifications describe the characteristics of the signals received and transmitted to the DS1 facility at the DS1 packet-based gateway interface (Figur

37、e 1). The signal delivered by the T1 carrier is received on the packet-based gateway T1 and R1 leads. The signal delivered by the packet-based gateway to the T1 carrier is transmitted on the T and R leads. The characteristics of the signals at the DS1 packet-based gateway interface are not symmetric

38、al; i.e., some of the electrical requirements differ for the transmit and receive signals. The terms transmit and receive are used to refer to signals from the perspective of the packet-based gateway. The requirements for the electrical interface are summarized below: Line Rate: 1544 kbps 32 ppm (50

39、 b/s). The tolerance is for operating without any synchronization to a network clock (e.g., self-timed, free-running). During synchronized operation, the line-rate accuracy shall be as specified in ANSI/TIA-594-B (Ref 8) and ANSI T1.101 (Ref 7) for the appropriate stratum level. Line Code: B8ZS. (Se

40、e text for pulse density constraints.) Test Load: Resistive termination of 100 5%. Pulse amplitude An isolated pulse transmitted from the Network to the packet-based gateway shall have a base-to-peak amplitude between 2.25 V and 3.6 V. An isolated pulse transmitted from the packet-based gateway to t

41、he Network shall have a base-to-peak amplitude between 2.4 V and 3.6 V. Pulse Shape: An isolated pulse shall fit the template shown in Figure 3. An isolated pulse is a pulse preceded by at least four zeros, and followed by at least one or more zeros. Power Levels: For an all “ones“ transmitted patte

42、rn, the power in a 3 1 kHz band centered about 772 kHz shall be in the range 12.4 to 19.7 dBm. The power in a 3 1 kHz band centered about 1544 kHz shall be at least 25 dB less than the power measured at 772 kHz. Pulse Imbalance: In any window of 17 consecutive bits, the maximum variation in pulse am

43、plitudes shall be less than 200 mV and the maximum variation in pulse width at half amplitude shall be less than 20 ns. 60 Hz Pulse Amplitude Variation: Pulse amplitude may vary at a 60 Hz rate as a result of longitudinal currents in the powering loops of T1 repeaters. In such cases, the envelope of

44、 the pulse amplitude shall be limited as shown in Figure 4. Any pulse amplitude in the ranges given above may be used as the 100% point in Figure 4. Notes: 1. The signal received by the packet-based gateway at the network interface has the characteristics specified above, with the exception that the

45、 pulse characteristics will be those of the standard signal transmitted through a cable pair with a loss in the range of 0.0 to 16.5 dB at 772 kHz into a 100 termination. The lower limit of the standard pulse amplitude shall be 2.25 V rather than 2.4 V. 2. Older equipment may have rate variations up

46、 to 128ppm ( 200 b/s). TIA-1062 Page 16 Time in Unit Intervals-0.500.000.501.001.50-1.00 -0.50 0.00 0.50 1.00 1.50Normalized AmplitudeMaximumcurveMinimumcurveNote: 1 Unit Interval = 648 nanoseconds DS1 Pulse Template Corner Points Minimum Curve Maximum Curve Time (Unit Intervals) Normalized Amplitud

47、e Time (Unit Intervals) Normalized Amplitude -0.77 -0.05 -0.77 0.05 -0.23 -0.05 -0.39 0.05-0.23 0.50 -0.27 0.80 -0.15 0.90 -0.27 1.200.00 0.95 -0.12 1.20 0.15 0.90 0.00 1.050.23 0.50 0.27 1.05 0.23 -0.45 0.34 -0.050.46 -0.45 0.77 0.05 0.61 -0.26 1.16 0.050.93 -0.05 1.16 -0.05 Successive corner point

48、s are joined by straight lines to form the template shown below: Figure 3 - DS1 Packet-based Gateway Interface Isolated Pulse Template TIA-1062 Page 17 Time (ms)Pulse Amplitude(Percent ofReference)11010075-75-100-1100 8.3 11.3 14.3 16.71/60Hz = 16.7 ms5.3Notes: 1. Envelope of pulse amplitudes shall

49、lie within the shaded areas. 2. Reference (100 percent point) may be any amplitude in the range of pulse amplitudes (see text). Figure 4 - Pulse Amplitude Envelope with 60 Hz Longitudinal Currents 5.2.2.1 Line Build Out (LBO) Networks To ensure that a usable DS1 signal is available to the public and private network, selectable artificial lines, or equivalent losses, shall be included in the transmit direction as part of the packet-based gateway interface circuitry. As a minimum, selectable values of 0.0, 7.5, and 15.0 dB of loss at 772 kHz shall be avai