ANSI TIA-455-122-B-2014 FOTP 122 Adopt IEC 60793-1-48 Measurement Methods and Test Procedures-Polarization Mode Dispersion.pdf

1、 TIA-455-122-B June 2014FOTP 122 Adopt IEC 60793-1-48: Measurement Methods and Test Procedures- Polarization Mode Dispersion ANSI/TIA-455-122-B-2014 APPROVED: MAY 21, 2014 NOTICE TIA Engineering Standards and Publications are designed to serve the public interest through eliminating misunderstanding

2、s between manufacturers and purchasers, facilitating interchangeability and improvement of products, and assisting the purchaser in selecting and obtaining with minimum delay the proper product for their particular need. The existence of such Standards and Publications shall not in any respect precl

3、ude any member or non-member of TIA from manufacturing or selling products not conforming to such Standards and Publications. Neither shall the existence of such Standards and Publications preclude their voluntary use by Non-TIA members, either domestically or internationally. Standards and Publicat

4、ions are adopted by TIA in accordance with the American National Standards Institute (ANSI) patent policy. By such action, TIA does not assume any liability to any patent owner, nor does it assume any obligation whatever to parties adopting the Standard or Publication. This Standard does not purport

5、 to address all safety problems associated with its use or all applicable regulatory requirements. It is the responsibility of the user of this Standard to establish appropriate safety and health practices and to determine the applicability of regulatory limitations before its use. Any use of tradem

6、arks in this document are for information purposes and do not constitute an endorsement by TIA or this committee of the products or services of the company. (From Project No. ANSI/TIA-PN-455.122-B-R1, formulated under the cognizance of the TIA TR-42 Telecommunications Cabling Systems, TR-42.12 Subco

7、mmittee on Optical Fibers and Cables). Published by TELECOMMUNICATIONS INDUSTRY ASSOCIATION Technology (b) there is no assurance that the Document will be approved by any Committee of TIA or any other body in its present or any other form; (c) the Document may be amended, modified or changed in the

8、standards development or any editing process. The use or practice of contents of this Document may involve the use of intellectual property rights (“IPR”), including pending or issued patents, or copyrights, owned by one or more parties. TIA makes no search or investigation for IPR. When IPR consist

9、ing of patents and published pending patent applications are claimed and called to TIAs attention, a statement from the holder thereof is requested, all in accordance with the Manual. TIA takes no position with reference to, and disclaims any obligation to investigate or inquire into, the scope or v

10、alidity of any claims of IPR. TIA will neither be a party to discussions of any licensing terms or conditions, which are instead left to the parties involved, nor will TIA opine or judge whether proposed licensing terms or conditions are reasonable or non-discriminatory. TIA does not warrant or repr

11、esent that procedures or practices suggested or provided in the Manual have been complied with as respects the Document or its contents. If the Document contains one or more Normative References to a document published by another organization (“other SSO”) engaged in the formulation, development or

12、publication of standards (whether designated as a standard, specification, recommendation or otherwise), whether such reference consists of mandatory, alternate or optional elements (as defined in the TIA Engineering Manual, 4thedition) then (i) TIA disclaims any duty or obligation to search or inve

13、stigate the records of any other SSO for IPR or letters of assurance relating to any such Normative Reference; (ii) TIAs policy of encouragement of voluntary disclosure (see Engineering Manual Section 6.5.1) of Essential Patent(s) and published pending patent applications shall apply; and (iii) Info

14、rmation as to claims of IPR in the records or publications of the other SSO shall not constitute identification to TIA of a claim of Essential Patent(s) or published pending patent applications. TIA does not enforce or monitor compliance with the contents of the Document. TIA does not certify, inspe

15、ct, test or otherwise investigate products, designs or services or any claims of compliance with the contents of the Document. ALL WARRANTIES, EXPRESS OR IMPLIED, ARE DISCLAIMED, INCLUDING WITHOUT LIMITATION, ANY AND ALL WARRANTIES CONCERNING THE ACCURACY OF THE CONTENTS, ITS FITNESS OR APPROPRIATEN

16、ESS FOR A PARTICULAR PURPOSE OR USE, ITS MERCHANTABILITY AND ITS NONINFRINGEMENT OF ANY THIRD PARTYS INTELLECTUAL PROPERTY RIGHTS. TIA EXPRESSLY DISCLAIMS ANY AND ALL RESPONSIBILITIES FOR THE ACCURACY OF THE CONTENTS AND MAKES NO REPRESENTATIONS OR WARRANTIES REGARDING THE CONTENTS COMPLIANCE WITH A

17、NY APPLICABLE STATUTE, RULE OR REGULATION, OR THE SAFETY OR HEALTH EFFECTS OF THE CONTENTS OR ANY PRODUCT OR SERVICE REFERRED TO IN THE DOCUMENT OR PRODUCED OR RENDERED TO COMPLY WITH THE CONTENTS. TIA SHALL NOT BE LIABLE FOR ANY AND ALL DAMAGES, DIRECT OR INDIRECT, ARISING FROM OR RELATING TO ANY U

18、SE OF THE CONTENTS CONTAINED HEREIN, INCLUDING WITHOUT LIMITATION ANY AND ALL INDIRECT, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES (INCLUDING DAMAGES FOR LOSS OF BUSINESS, LOSS OF PROFITS, LITIGATION, OR THE LIKE), WHETHER BASED UPON BREACH OF CONTRACT, BREACH OF WARRANTY, TORT (INCLUDING NEGLIGEN

19、CE), PRODUCT LIABILITY OR OTHERWISE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. THE FOREGOING NEGATION OF DAMAGES IS A FUNDAMENTAL ELEMENT OF THE USE OF THE CONTENTS HEREOF, AND THESE CONTENTS WOULD NOT BE PUBLISHED BY TIA WITHOUT SUCH LIMITATIONS. 2 60793-1-48 IEC:2007 CONTENTS FOREWORD 4

20、INTRODUCTION 6 1 Scope 7 2 Normative references7 3 Terms and definitions .8 4 General8 4.1 Methods for measuring PMD 8 4.2 Reference test method.10 4.3 Applicability.10 5 Apparatus 11 5.1 Light source and polarizers 11 5.2 Input optics .11 5.3 Input positioner12 5.4 Cladding mode stripper 12 5.5 Hig

21、h-order mode filter 12 5.6 Output positioner .12 5.7 Output optics.12 5.8 Detector 12 5.9 Computer 12 6 Sampling and specimens 12 6.1 General.12 6.2 Specimen length13 6.3 Deployment .13 7 Procedure 14 8 Calculation or interpretation of results .14 9 Documentation .14 9.1 Information required for eac

22、h measurement 14 9.2 Information to be available .14 10 Specification information.15 Annex A (normative) Fixed analyser measurement method 16 Annex B (normative) Stokes evaluation method.27 Annex C (normative) Interferometry method 32 Annex D (informative) Determination of RMS width from a fringe en

23、velope .42 Annex E (informative) Glossary of symbols .46 Bibliography .48 Figure A.1 Block diagrams for Method A .16 Figure A.2 Typical results from Method A19 Figure A.3 PMD by Fourier analysis22 Figure A.4 Cross-correlation and autocorrelation functions.26 60793-1-48 IEC:2007 3 Figure B.1 Block di

24、agram for Method B .27 Figure B.2 Typical random-mode-coupling results from Method B.29 Figure B.3 Typical histogram of DGD values .29 Figure C.1 Schematic diagram for Method C (generic implementation) .32 Figure C.2 Other schematic diagrams for Method C.34 Figure C.3a Random mode-coupling using a T

25、INTY-based measurement system with one I/O SOP37 Figure C.3b Negligible mode-coupling using a TINTY-based measurement system with one I/O SOP37 Figure C.3 Fringe envelopes for negligible and random polarization mode-coupling.37 Figure C.4a Random mode-coupling using a GINTY-based measurement system

26、with I/O-SOP scrambling .38 Figure C.4b Negligible mode-coupling using a GINTY-based measurement system with I/O-SOP scrambling .38 Figure C.4c Mixed mode-coupling using a GINTY-based measurement system with I/O-SOP scrambling 39 Figure C.4 Fringe envelopes for negligible and random polarization mod

27、e-coupling (Ginty procedure)39 Figure D.1 Parameters for interferogram analysis 42 Table A.1 Cosine transform calculations .25 4 60793-1-48 IEC:2007 INTERNATIONAL ELECTROTECHNICAL COMMISSION _ OPTICAL FIBRES Part 1-48: Measurement methods and test procedures Polarization mode dispersion FOREWORD 1)

28、The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising all national electrotechnical committees (IEC National Committees). The object of IEC is to promote international co-operation on all questions concerning standardization in the electrical

29、and electronic fields. To this end and in addition to other activities, IEC publishes International Standards, Technical Specifications, Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC Publication(s)”). Their preparation is entrusted to technical

30、committees; any IEC National Committee interested in the subject dealt with may participate in this preparatory work. International, governmental and non-governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely with the International Organizatio

31、n for Standardization (ISO) in accordance with conditions determined by agreement between the two organizations. 2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international consensus of opinion on the relevant subjects since each technical commi

32、ttee has representation from all interested IEC National Committees. 3) IEC Publications have the form of recommendations for international use and are accepted by IEC National Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC Publications is

33、 accurate, IEC cannot be held responsible for the way in which they are used or for any misinterpretation by any end user. 4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications transparently to the maximum extent possible in their national and r

34、egional publications. Any divergence between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in the latter. 5) IEC provides no marking procedure to indicate its approval and cannot be rendered responsible for any equipment declared to be in confo

35、rmity with an IEC Publication. 6) All users should ensure that they have the latest edition of this publication. 7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and members of its technical committees and IEC National Committees for an

36、y personal injury, property damage or other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC Publications. 8) Attention is drawn to the Normati

37、ve references cited in this publication. Use of the referenced publications is indispensable for the correct application of this publication. 9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of patent rights. IEC shall not be held responsi

38、ble for identifying any or all such patent rights. International Standard IEC 60793-1-48 has been prepared by subcommittee 86A: Fibres and cables, of IEC technical committee 86: Fibre optics. This second edition cancels and replaces the first edition published in 2003. It constitutes a technical rev

39、ision. In this edition, reference to IEC 61282-9 has resulted in the removal of Annexes E, F, G and H as well as the creation of a new Annex E. The text of this standard is based on the following documents: CDV Report on voting86A/1038/CDV 86A/1078/RVC Full information on the voting for the approval

40、 of this standard can be found in the report on voting indicated in the above table. This publication has been drafted in accordance with the ISO/IEC Directives, Part 2. 60793-1-48 IEC:2007 5 This standard is to be read in conjunction with IEC 60793-1-1. A list of all parts of the IEC 60793 series,

41、published under the general title Optical fibres, can be found on the IEC website. The committee has decided that the contents of this publication will remain unchanged until the maintenance result date indicated on the IEC web site under “http:/webstore.iec.ch“ in the data related to the specific p

42、ublication. At this date, the publication will be reconfirmed; withdrawn; replaced by a revised edition, or amended. 6 60793-1-48 IEC:2007 INTRODUCTION Polarization mode dispersion (PMD) causes an optical pulse to spread in the time domain. This dispersion could impair the performance of a telecommu

43、nications system. The effect can be related to differential phase and group velocities and corresponding arrival times of different polarization components of the signal. For a sufficiently narrow band source, the effect can be related to a differential group delay (DGD), , between pairs of orthogon

44、ally polarized principal states of polarization (PSP) at a given wavelength. For broadband transmission, the delays bifurcate and result in an output pulse that is spread out in the time domain. In this case, the spreading can be related to the average of DGD values. In long fibre spans, DGD is rand

45、om in both time and wavelength since it depends on the details of the birefringence along the entire fibre length. It is also sensitive to time-dependent temperature and mechanical perturbations on the fibre. For this reason, a useful way to characterize PMD in long fibres is in terms of the expecte

46、d value, , or the mean DGD over wavelength. In principle, the expected value does not undergo large changes for a given fibre from day to day or from source to source, unlike the parameters or . In addition, is a useful predictor of lightwave system performance. The term “PMD“ is used both in the ge

47、neral sense of two polarization modes having different group velocities, and in the specific sense of the expected value . The DGD or pulse broadening can be averaged over wavelength, yielding , or time, yielding t, or temperature, yielding T. For most purposes, it is not necessary to distinguish be

48、tween these various options for obtaining . The coupling length lcis the length of fibre or cable at which appreciable coupling between the two polarization states begins to occur. If the fibre length L satisfies the condition L scales with fibre length. The corresponding PMD coefficient is “short-l

49、ength“ PMD coefficient = /L. Fibres in practical systems are nearly always in the L lc, regime and mode coupling is random. If mode coupling is also found to be random, scales with the square root of fibre length, and “long-length“ PMD coefficient = / L 60793-1-48 IEC:2007 7 OPTICAL FIBRES Part 1-48: Measurement methods and test procedures Polarization mode dispersion 1 Scope This part of IEC 60793 applies to three methods of measuring polarization mode dispersion (PMD), wh