ANSI TIA-568.2-C-2-2014 Balanced Twisted-Pair Telecommunications Cabling and Components Standard Addendum 2 Alternative Test Methodology for Category 6A Patch Cords (Addendum to TI.pdf

1、 TIA-568-C.2-2 November 2014Balanced Twisted-Pair Telecommunications Cabling and Components Standard, Addendum 2: Alternative Test Methodology for Category 6A Patch Cords ANSI/TIA-568-C.2-2-2014 APPROVED: NOVEMBER 7, 2014 NOTICE TIA Engineering Standards and Publications are designed to serve the pu

2、blic interest through eliminating misunderstandings between manufacturers and purchasers, facilitating interchangeability and improvement of products, and assisting the purchaser in selecting and obtaining with minimum delay the proper product for their particular need. The existence of such Standar

3、ds and Publications shall not in any respect preclude any member or non-member of TIA from manufacturing or selling products not conforming to such Standards and Publications. Neither shall the existence of such Standards and Publications preclude their voluntary use by Non-TIA members, either domes

4、tically or internationally. Standards and Publications are adopted by TIA in accordance with the American National Standards Institute (ANSI) patent policy. By such action, TIA does not assume any liability to any patent owner, nor does it assume any obligation whatever to parties adopting the Stand

5、ard or Publication. This Standard does not purport to address all safety problems associated with its use or all applicable regulatory requirements. It is the responsibility of the user of this Standard to establish appropriate safety and health practices and to determine the applicability of regula

6、tory limitations before its use. Any use of trademarks in this document are for information purposes and do not constitute an endorsement by TIA or this committee of the products or services of the company. (From Project No. ANSI/TIA-PN-568-C.2-2, formulated under the cognizance of the TIA TR-42 Tel

7、ecommunications Cabling Systems, TR-42.7 Subcommittee on Telecommunications Copper Cabling Systems (568). Published by TELECOMMUNICATIONS INDUSTRY ASSOCIATION Technology and Standards Department 1320 N. Courthouse Road, Suite 200 Arlington, VA 22201 U.S.A. PRICE: Please refer to current Catalog of T

8、IA TELECOMMUNICATIONS INDUSTRY ASSOCIATION STANDARDS AND ENGINEERING PUBLICATIONS or call IHS, USA and Canada (1-877-413-5187) International (303-397-2896) or search online at http:/www.tiaonline.org/standards/catalog/ All rights reserved Printed in U.S.A. NOTICE OF COPYRIGHT This document is copyri

9、ghted by the TIA. Reproduction of these documents either in hard copy or soft copy (including posting on the web) is prohibited without copyright permission. For copyright permission to reproduce portions of this document, please contact the TIA Standards Department or go to the TIA website (www.tia

10、online.org) for details on how to request permission. Details are located at: http:/www.tiaonline.org/standards/catalog/info.cfm#copyright or Telecommunications Industry Association Technology (b) there is no assurance that the Document will be approved by any Committee of TIA or any other body in i

11、ts present or any other form; (c) the Document may be amended, modified or changed in the standards development or any editing process. The use or practice of contents of this Document may involve the use of intellectual property rights (“IPR”), including pending or issued patents, or copyrights, ow

12、ned by one or more parties. TIA makes no search or investigation for IPR. When IPR consisting of patents and published pending patent applications are claimed and called to TIAs attention, a statement from the holder thereof is requested, all in accordance with the Manual. TIA takes no position with

13、 reference to, and disclaims any obligation to investigate or inquire into, the scope or validity of any claims of IPR. TIA will neither be a party to discussions of any licensing terms or conditions, which are instead left to the parties involved, nor will TIA opine or judge whether proposed licens

14、ing terms or conditions are reasonable or non-discriminatory. TIA does not warrant or represent that procedures or practices suggested or provided in the Manual have been complied with as respects the Document or its contents. If the Document contains one or more Normative References to a document p

15、ublished by another organization (“other SSO”) engaged in the formulation, development or publication of standards (whether designated as a standard, specification, recommendation or otherwise), whether such reference consists of mandatory, alternate or optional elements (as defined in the TIA Proce

16、dures for American National Standards) then (i) TIA disclaims any duty or obligation to search or investigate the records of any other SSO for IPR or letters of assurance relating to any such Normative Reference; (ii) TIAs policy of encouragement of voluntary disclosure (see TIA Procedures for Ameri

17、can National Standards Annex C.1.2.3) of Essential Patent(s) and published pending patent applications shall apply; and (iii) Information as to claims of IPR in the records or publications of the other SSO shall not constitute identification to TIA of a claim of Essential Patent(s) or published pend

18、ing patent applications. TIA does not enforce or monitor compliance with the contents of the Document. TIA does not certify, inspect, test or otherwise investigate products, designs or services or any claims of compliance with the contents of the Document. ALL WARRANTIES, EXPRESS OR IMPLIED, ARE DIS

19、CLAIMED, INCLUDING WITHOUT LIMITATION, ANY AND ALL WARRANTIES CONCERNING THE ACCURACY OF THE CONTENTS, ITS FITNESS OR APPROPRIATENESS FOR A PARTICULAR PURPOSE OR USE, ITS MERCHANTABILITY AND ITS NONINFRINGEMENT OF ANY THIRD PARTYS INTELLECTUAL PROPERTY RIGHTS. TIA EXPRESSLY DISCLAIMS ANY AND ALL RES

20、PONSIBILITIES FOR THE ACCURACY OF THE CONTENTS AND MAKES NO REPRESENTATIONS OR WARRANTIES REGARDING THE CONTENTS COMPLIANCE WITH ANY APPLICABLE STATUTE, RULE OR REGULATION, OR THE SAFETY OR HEALTH EFFECTS OF THE CONTENTS OR ANY PRODUCT OR SERVICE REFERRED TO IN THE DOCUMENT OR PRODUCED OR RENDERED T

21、O COMPLY WITH THE CONTENTS. TIA SHALL NOT BE LIABLE FOR ANY AND ALL DAMAGES, DIRECT OR INDIRECT, ARISING FROM OR RELATING TO ANY USE OF THE CONTENTS CONTAINED HEREIN, INCLUDING WITHOUT LIMITATION ANY AND ALL INDIRECT, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES (INCLUDING DAMAGES FOR LOSS OF BUSINE

22、SS, LOSS OF PROFITS, LITIGATION, OR THE LIKE), WHETHER BASED UPON BREACH OF CONTRACT, BREACH OF WARRANTY, TORT (INCLUDING NEGLIGENCE), PRODUCT LIABILITY OR OTHERWISE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. THE FOREGOING NEGATION OF DAMAGES IS A FUNDAMENTAL ELEMENT OF THE USE OF THE CONT

23、ENTS HEREOF, AND THESE CONTENTS WOULD NOT BE PUBLISHED BY TIA WITHOUT SUCH LIMITATIONS. ANSI/TIA-568-C.2-2 i Balanced Twisted-Pair Telecommunications Cabling and Components Standard, Addendum 2: Alternative Test Methodology for Category 6A Patch Cords TABLE OF CONTENTS FOREWORD ii 1 SCOPE 1 2 NORMAT

24、IVE AND INFORMATIVE REFERENCES . 1 3 DEFINITIONS, ABBREVIATIONS AND ACRONYMS, UNITS OF MEASURE 1 4 GENERAL 1 4.1 Alternative test head NEXT loss requirements 1 4.2 Category 6A patch cord NEXT loss requirements when measured using alternative test head . 2 4.3 Other category 6A modular cord requireme

25、nts when measured using alternative test head 2 Annex A (informative) - Bibliography . 3 LIST OF TABLES Table 1 - Alternative test head NEXT loss requirements 1 Table 2 - Alternative test head NEXT loss requirements when using high and low 36-45 virtual test plugs 1 Table 3 - Minimum category 6A wor

26、k area, equipment and patch cord NEXT Loss when using alternative test head 2 ANSI/TIA-568-C.2-2 ii FOREWORD (This foreword is not a part of this Addendum) This Addendum was developed by TIA Subcommittee TR-42.7. Approval of this Addendum This Addendum was approved by TIA Subcommittee TR-42.7, TIA E

27、ngineering Committee TR-42, and the American National Standards Institute (ANSI). ANSI/TIA reviews standards every 5 years. At that time, standards are reaffirmed, rescinded, or revised according to the submitted updates. Updates to be included in the next revision should be sent to the committee ch

28、air or to ANSI/TIA. Contributing Organizations More than 30 organizations within the telecommunications industry contributed their expertise to the development of this Addendum (including manufacturers, consultants, end users, and other organizations). Documents superseded This provides an Addendum

29、to the ANSI/TIA-568-C.2 standard dated August 11, 2009 to specify the use of an alternative patch cord test head when characterizing category 6A patch cords. Since the original publication of ANSI/EIA/TIA-568-C.2 in August of 2009 international standards such as ISO/IEC 61935-2 require the use of a

30、different performance of connector for measurement of category 6A cords compared to ANSI/TIA-568-C.2. This creates practical differences in field and laboratory measurements of category 6A cords. This document presents a refinement to ANSI/TIA-568-C.2 which allows convenient measurement of category

31、6A cords to both TIA and international standards. This Addendum incorporates and refines the technical content of: - ANSI/TIA-568-C.2 Significant technical changes from ANSI/TIA-568-C.2 Incorporation of an alternative patch cord test head for category 6A cords Instructions on how to calculate limit

32、lines for category 6A cords according to ANSI/TIA-568-C.2 when using the alternative test heads. Annexes Annex A is informative and is not considered a requirement of this Addendum. ANSI/TIA-568-C.2-2 iii Introduction This Addendum provides requirements for an alternative category 6A patch cord test

33、 head. TIA category 6A jacks and ISO/IEC category 6A jacks used for measurement of patch cords have slightly differing requirements. These cause negligible difference to measured patch cord results, however they create a situation where it is difficult and impractical to make a patch cord test head

34、that is both TIA and ISO/IEC compliant. This causes practical difficulties in both laboratory and field measurements of cords. Purpose This Addendum provides requirements for an alternative category 6A patch cord test head, and guidelines for calculation of category 6A patch cord requirements when u

35、sing these test heads. Specification of criteria Two categories of criteria are specified; mandatory and advisory. The mandatory requirements are designated by the word “shall“; advisory requirements are designated by the words “should”, “may“, or “desirable“ which are used interchangeably in this A

36、ddendum. Mandatory criteria generally apply to protection, performance, administration and compatibility; they specify the absolute minimum acceptable requirements. Advisory or desirable criteria are presented when their attainment will enhance the general performance of the cabling system in all it

37、s contemplated applications. A note in the text, table, or figure is used for emphasis or offering informative suggestions. Metric equivalents of US customary units The majority of the metric dimensions in this Addendum are metric with approximate conversions to US customary units; e.g., 4 inches (i

38、n) is the approximate conversion of 100 millimeters (mm). Life of the Addendum This Addendum is a living document. The criteria contained in this Addendum are subject to revisions and updating as warranted by advances in building construction techniques and telecommunications technology.ANSI/TIA-568

39、-C.2-2 ANSI/TIA-568-C.2-2 1 1 SCOPE This Addendum specifies requirements for an alternative category 6A patch cord test head and provides guidelines for how to calculate requirements for category 6A cords when this patch cord test head is used. This Addendum is only applicable to category 6A patch c

40、ords according to ANSI/TIA-568-C.2. 2 NORMATIVE AND INFORMATIVE REFERENCES None. 3 DEFINITIONS, ABBREVIATIONS AND ACRONYMS, UNITS OF MEASURE For the purpose of this Addendum the definitions, acronyms, abbreviations and units of measure from ANSI/TIA-568-C.2 apply. 4 GENERAL When testing a category 6

41、A patch cord according to ANSI/TIA-568-C.2 it is permitted to use test heads according to the requirements of 4.1. When using test heads according to clause 4.1 the category 6A patch cord NEXT requirements shall be according to clause 4.2. 4.1 Alternative test head NEXT loss requirements Mated modul

42、ar cord test head NEXT loss shall be measured for all pair combinations in accordance with ANSI/TIA-568-C.2 clause C.4.4. For all frequencies from 10 MHz to 500 MHz, modular test head NEXT loss performance shall meet the connecting hardware NEXT loss requirements specified in table 1. Table 1 - Alte

43、rnative test head NEXT loss requirements Frequency (MHz) NEXT loss (dB) Category 6A 10 f 250 250 f 500 )100/log(2054 f )250/log(3004.46 f In addition, the best case NEXT loss performance of the mated modular cord test head shall be centered for pair combinations 3,6-4,5; 1,2-3,6; and 3,6-7,8 as veri

44、fied by the following procedure. 1. Measure the mated NEXT loss throughout the frequency range from 10 to 500 MHz for the low and high virtual test plugs per the procedures in clause ANSI/TIA-568-C.2 clause C.4.4. 2. Determine the minimum margin (dB) to the NEXT loss requirements as specified in tab

45、le 2 for pair combination 3,6-4,5 and table 1 for pair combinations 1,2-3,6 and 3,6-7,8 from 10 to 500 MHz for both the low and high virtual test plugs. Table 2 - Alternative test head NEXT loss requirements when using high and low 36-45 virtual test plugs Frequency (MHz) NEXT loss (dB) Category 6A

46、10 f 250 250 f 500 )100/log(205.52 f )250/log(3054.44 f ANSI/TIA-568-C.2-2 2 3. The difference between these minimum margins for the high and low limit-value virtual test plugs shall be less than 2 dB for the pair combination terminated on pins 3,6 4,5 and 4 dB for the pair combinations terminated o

47、n pins 1,2-3,6 and 3,6-7,8. There are no centering requirements for pair combinations 1,2-4,5; 4,5-7,8; or 1,2-7,8. In addition the test head according to this Addendum shall also comply to FEXT loss requirements of ANSI/TIA-568-C.2 clause C.5.2.2 and Return Loss requirements of ANSI/TIA-568-C.2 cla

48、use C.5.2.3. 4.2 Category 6A patch cord NEXT loss requirements when measured using alternative test head The modular plug cord test limits shall be calculated using the connector contribution corresponding to the NEXT limits used for test head qualification. When the alternative test head is used, t

49、he NEXT loss requirement for category 6A cords shall be calculated according to ANSI/TIA-568-C.2 clause 6.9.2 equation 28, and the values provided by table 1 shall be used for term NEXTconn_spec in ANSI/TIA-568-C.2 clause 6.9.2 equation 29. The work area, equipment, and patch cord minimum NEXT loss values in table 3 are provided for information only. Table 3 - Minimum category 6A work area, equipment, and patch cord NEXT Loss when using alternative test head Frequency(MHz) 2m (dB) 5m (dB) 10m (dB) 1.00 65.0 65.0 65.0 4.00 65.0 65.0 65.0 8.00 6