ANSI UL 1363-2018 UL Standard for Safety Relocatable Power Taps (Fifth Edition).pdf

1、UL 1363 Relocatable Power Taps STANDARD FOR SAFETYUL Standard for Safety for Relocatable Power Taps, UL 1363 Fifth Edition, Dated June 12, 2018 Summary of Topics This new edition of ANSI/UL 1363 reects the First time ANSI approval of the Standard, as well as the following changes in requirements: RP

2、T Employing Tamper-Resistant Outlets Miscellaneous Editorial Corrections The new and revised requirements are substantially in accordance with Proposal(s) on this subject dated November 17, 2017 and April 20, 2018. All rights reserved. No part of this publication may be reproduced, stored in a retri

3、eval system, or transmitted in any form by any means, electronic, mechanical photocopying, recording, or otherwise without prior permission of UL. UL provides this Standard as is without warranty of any kind, either expressed or implied, including but not limited to, the implied warranties of mercha

4、ntability or tness for any purpose. In no event will UL be liable for any special, incidental, consequential, indirect or similar damages, including loss of prots, lost savings, loss of data, or any other damages arising out of the use of or the inability to use this Standard, even if UL or an autho

5、rized UL representative has been advised of the possibility of such damage. In no event shall ULs liability for any damage ever exceed the price paid for this Standard, regardless of the form of the claim. Users of the electronic versions of ULs Standards for Safety agree to defend, indemnify, and h

6、old UL harmless from and against any loss, expense, liability, damage, claim, or judgment (including reasonable attorneys fees) resulting from any error or deviation introduced while purchaser is storing an electronic Standard on the purchasers computer system. UL COPYRIGHTED MATERIAL NOT AUTHORIZED

7、 FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL JUNE 12, 2018 UL 1363 tr1JUNE 12, 2018 UL 1363 tr2 No Text on This PageJUNE 12, 2018 1 UL 1363 Standard for Relocatable Power Taps The rst edition was titled Temporary Power Taps. First Edition June, 1991 Second Edition December, 1

8、996 Third Edition May, 2007 Fourth Edition October, 2014 Fifth Edition June 12, 2018 This ANSI/UL Standard for Safety consists of the Fifth Edition. The most recent designation of ANSI/UL 1363 as an American National Standard (ANSI) occurred on June 12, 2018. ANSI approval for a standard does not in

9、clude the Cover Page, Transmittal Pages, and Title Page. Comments or proposals for revisions on any part of the Standard may be submitted to UL at any time. Proposals should be submitted via a Proposal Request in ULs On-Line Collaborative Standards Development System (CSDS) at https:/. ULs Standards

10、 for Safety are copyrighted by UL. Neither a printed nor electronic copy of a Standard should be altered in any way. All of ULs Standards and all copyrights, ownerships, and rights regarding those Standards shall remain the sole and exclusive property of UL. COPYRIGHT 2018 UNDERWRITERS LABORATORIES

11、INC. ANSI/UL 1363-2018JUNE 12, 2018 RELOCATABLE POWER TAPS - UL 1363 2 No Text on This PageCONTENTS INTRODUCTION 1 Scope .7 2 Components8 3 Units of Measurement .9 4 Undated References 9 5Use .9 6 Glossary .9 CONSTRUCTION 7 General.12 8 Enclosure .13 8.1 General 13 8.2 Metallic.14 8.3 Nonmetallic .1

12、4 9 Mechanical Assembly 15 10 Accessibility of Live Parts 16 11 Temporary Mounting Means .18 12 Corrosion Protection 18 13 Insulating Materials .19 14 Power-Supply Cord .19 14.1 General .19 14.2 Class 2 lead .21 14.3 Bushings 21 15 Strain Relief21 16 Receptacles22 17 Supplementary Protection23 18 Sw

13、itches.24 19 Live Parts25 20 Internal Wiring25 21 Spacings 26 22 Clearance and Creepage Distances Isolated Secondary Circuits27 23 Printed-Wiring Boards .28 24 Separation of Circuits .29 25 Grounding .29 25.1 General .29 25.2 Bonding .31 26 Storage Compartment .32 27 Cord Reel Feature 32 28 Low Volt

14、age Charging and Isolated Secondary Output Circuits .32 PERFORMANCE 29 General32 30 Temperature Test.33 31 Dielectric Voltage-Withstand Test .35 32 Leakage Current Test .36 32.1 General .36 32.2 Leakage current after humidity conditioning39 JUNE 12, 2018 RELOCATABLE POWER TAPS - UL 1363 333 Groundin

15、g Continuity Test .39 34 Fault Current Test 40 34.1 General .40 34.2 Calibration of test circuits40 35 Overcurrent Test41 36 Mounting Hole Barrier Tests .42 36.1 General .42 36.2 Mounting hole barrier impact test.43 36.3 Mounting hole barrier probe test .44 37 Strain Relief Test .44 38 Impact Tests

16、.45 38.1 General .45 38.2 Drop impact test .46 38.3 Steel sphere impact test 47 38.4 Low-temperature steel sphere impact test .50 39 Crushing Test 50 40 Adequacy of Mounting Test 51 41 Stability Test .52 41.1 General .52 41.2 Test method general 52 41.3 Pedestal mounted RPT with multiple or articula

17、ted columns .52 41.4 Pedestal mounted RPT having provisions for loading .52 41.5 Pedestal mounted RPT over 54 in (1472 mm) in height .52 42 Tipover Test .53 43 Mold Stress-Relief Distortion Test.53 44 Spill Test 54 45 Water Leakage Test 54 46 Permanence of Cord Tag Test .55 46.1 General .55 46.2 Con

18、ditioning .55 46.3 Test Method .56 47 Flexing Endurance Test .56 MANUFACTURING AND PRODUCTION-LINE TESTS 48 Dielectric Voltage-Withstand Test .57 49 Grounding Continuity Test .59 RATINGS 50 Details.59 MARKINGS 51 Details.59 INSTRUCTIONS 52 Details.62 JUNE 12, 2018 RELOCATABLE POWER TAPS - UL 1363 4S

19、UPPLEMENT SA - EXTENDABLE RELOCATABLE POWER TAPS INTRODUCTION SA1 Scope SA1 SA2 GlossarySA1 CONSTRUCTION SA3 General SA2 SA4 Electrical Contact Devices SA2 SA4.1 General SA2 SA4.2 Mating connectors.SA2 SA4.3 Flammability SA3 SA4.4 Electrical properties .SA3 SA4.5 Thermal properties SA4 SA4.6 Mating

20、connector physical requirements .SA4 SA5 EnclosuresSA4 SA6 Performance SA5 SA6.1 General SA5 SA6.2 Locking and latching tests SA5 SA6.3 Mating connector tests .SA6 SA7 Markings .SA7 SA8 Instruction Manual .SA8 SUPPLEMENT SB - RELOCATABLE POWER TAPS INCORPORATING BATTERIES INTRODUCTION SB1 Scope SB1

21、SB2 GlossarySB1 SB3 General SB2 SB4 Battery Chargers and Circuits .SB2 CONSTRUCTION SB5 BatteriesSB2 SB5.1 General SB2 SB5.2 Non-replaceable batteries .SB3 SB5.3 Technician replaceable batteries SB3 SB5.4 User replaceable batteriesSB3 SB5.5 Battery packs .SB3 SB5.6 Lithium-ion battery cells or packs

22、SB3 SB6 Battery Compartments .SB4 SB7 Battery Circuits SB5 SB8 Battery Charging SB5 JUNE 12, 2018 RELOCATABLE POWER TAPS - UL 1363 5PERFORMANCE SB9 Temperature TestSB5 SB9.1 General SB5 SB9.2 Temperature test method I .SB6 SB9.3 Temperature test method II.SB6 SB9.4 Temperature test method III SB6 SB

23、10 Discharge Test .SB6 SB11 Lithium-ion Batteries SB7 SB11.1 Lithium-ion battery abnormal testsSB7 SB11.2 Impact tests .SB8 SB12 Markings SB9 SB13 Installation and Operation Instructions.SB9 SUPPLEMENT SC - RELOCATABLE POWER TAPS EMPLOYING AN INTEGRAL THERMAL INTERRUPTION MECHANISM INTRODUCTION SC1

24、ScopeSC1 SC2 Glossary .SC1 CONSTRUCTION SC3 General SC1 PERFORMANCE SC4 General SC2 SC5 Abnormal Slow Heat Rise TestSC2 SC6 Abnormal Fast Heat Rise Test SC4 SC7 Abnormal Switch TestSC4 MARKINGS SC8 Details .SC5 INSTRUCTIONS SC9 Details .SC5 APPENDIX A Standards for ComponentsA1 JUNE 12, 2018 RELOCAT

25、ABLE POWER TAPS - UL 1363 6INTRODUCTION 1 Scope 1.1 These requirements cover indoor use cord and plug connected, relocatable power taps (RPT) rated 250 V AC or less and 20 Amperes or less. A RPT may include an integral Class 2 power supply with an integral lead and/or connector(s) output. In accorda

26、nce with the National Electric Code, NFPA 70, RPT are for use as a movable power supply connection for cord and plug connected electrical utilization equipment and shall not serve as xed wiring of a structure or of xed furnishings, such as but not limited to applications in permanent countertops of

27、kitchens and bathrooms. 1.2 A cord-and-plug-connected product as described in 1.1 with less than three receptacle outlets and provided with a Luminaire is covered under the Standard for Portable Electric Luminaires, UL 153. 1.3 A cord-and-plug-connected product as described in 1.1 with less than thr

28、ee receptacle outlets that employs an electromagnetic interference lter is covered under the Standard for Electromagnetic Interference Filters, UL 1283. 1.4 A cord-and-plug-connected product as described in 1.1 with less than three receptacle outlets that employs a surge protective device (SPD) is c

29、overed under the Standard for Surge Protective Devices, UL 1449, for SPD Type 3. 1.5 These requirements cover RPT with more than two receptacle outlets that employ a surge protective device (SPD) shall also comply with the applicable requirements for cord-connected, Type 3 Surge Protective Device (S

30、PD) in the Standard for Surge Protective Devices, UL 1449. 1.6 A cord-and-plug-connected product as described in 1.1 that employs ground-fault protection is covered under the requirements for portable GFCIs in the Standard for Ground-Fault Circuit Interrupters, UL 943. 1.7 This standard does not cov

31、er RPT including those employing Hospital Grade receptacles or Hospital Grade plugs (see 52.1), intended for use with medical equipment. RPT are not suitable for use in Category 2 (General Patient Care) Spaces or Category 1 (Critical Patient Care) Spaces or Patient Care Vicinities of health care fac

32、ilities. 1.8 These requirements do not cover a cord-and plug-connected product, Health Care Facility Receptacle Assemblies (HCOA), covered by the Outline of Investigation for Cord-and-Plug-Connected Health Care Facility Outlet Assemblies, UL 2930. HCOA are intended as a movable power supply connecti

33、on for cord-and-plug-connected medical electrical utilization equipment for use in Category 2 (General Patient Care) Spaces or Category 1 (Critical Patient Care) Spaces, including Patient Care Vicinities equipped with Patient Equipment Grounding Points, of health care facilities. 1.9 These requireme

34、nts do not cover a cord-and-plug-connected component, Special Purpose Relocatable Power Taps (SPRPT), covered by the covered in the Outline of Investigations Special Purpose Relocatable Power Taps, UL 1363A. SPRPT are power distribution components intended to supply power to plug-connected component

35、s of a movable equipment assemblies that are rack, table, or pedestal-mounted. SPRPT are intended for use as components of complete equipment submitted for investigation rather than for direct separate installation in the eld. The SPRPT shall be an integral part of the equipment assembly and permane

36、ntly attached to the equipment assembly only by those qualied to assemble medical electrical equipment systems compliant with Medical Electrical Equipment Part 1: General Requirements for Basic Safety and Essential Performance, IEC 60601-1. SPRPT are not suitable for use in Patient Care Vicinities.

37、JUNE 12, 2018 RELOCATABLE POWER TAPS - UL 1363 71.10 A RPT may employ an integral cord reel for the supply cord and attachment plug. A cord reel provided with pull out receptacle outlets or cord connectors is covered under the Standard for Cord Reels, UL 355. 1.11 These requirements do not cover RPT

38、 with work surfaces or surfaces intended to support weight loads other than as specied in 6.16 for the storage of hand-held electronic devices and charging equipment such as a cell phone, cell phone charger and the like. 1.12 These requirements cover RPT provided with isolated secondary circuits. 1.

39、13 These requirements cover RPT provided with batteries located in isolated secondary circuits. See UL 1363 Supplement SB Relocatable Power Taps Incorporating Batteries. 1.14 A product that has a battery backup feature or other uninterruptible power supply equipment located in the Primary Circuit sh

40、all comply with the applicable requirements in the Standard for Uninterruptible Power Supply Equipment, UL 1778. 1.15 A RPT with three or more receptacle outlets may employ a Light Emitting Diode (LED) Luminaire. 1.16 A cord-and-plug-connected product as described in 1.1 for xed mounting by use of t

41、ools to portable or stationary furnishings is covered under the requirements in the Standard for Furniture Power Distribution Units, UL 962A. 1.17 This standard contains the following Supplements: a) Supplement SA Extendable Relocatable Power Taps. b) Supplement SB Relocatable Power Taps Incorporati

42、ng Batteries. c) Supplement SC Relocatable Power Taps Employing An Integral Thermal Interruption Mechanism. 2 Components 2.1 Except as indicated in 2.2, a component of a product covered by this standard shall comply with the requirements for that component. See Appendix A for a list of standards cov

43、ering components used in the products covered by this standard. 2.2 A component is not required to comply with a specic requirement that: a) Involves a feature or characteristic not required in the application of the component in the product covered by this standard, or b) Is superseded by a require

44、ment in this standard. 2.3 A component shall be used in accordance with its rating established for the intended conditions of use. JUNE 12, 2018 RELOCATABLE POWER TAPS - UL 1363 82.4 Specic components are incomplete in construction features or restricted in performance capabilities. Such components

45、are intended for use only under limited conditions, such as certain temperatures not exceeding specied limits, and shall be used only under those specic conditions. 2.1.5 A RPT that incorporates a LED Luminaire and LED components and subassemblies shall comply with the applicable requirements of the

46、 Standard for Light Emitting Diode (LED) Equipment for Use in Lighting Products, UL 8750. 3 Units of Measurement 3.1 Values stated without parentheses are the requirement. Values in parentheses are explanatory or approximate information. 3.2 Unless otherwise indicated, all voltage and current values

47、 mentioned in this standard are root-mean-square (rms). 4 Undated References 4.1 Any undated reference to a code or standard appearing in the requirements of this standard shall be interpreted as referring to the latest edition of that code or standard. 5 Use 5.1 A RPT is intended to be connected to

48、 a permanently installed branch circuit receptacle outlet. 5.2 A RPT is not intended to be permanently mounted. 5.3 A RPT is not intended to be series connected (daisy chained) to other RPT or to extension cords. 6 Glossary 6.1 For the purpose of this standard the following denitions apply. 6.2 ATTA

49、CHMENT PLUG A male contact device for the temporary connection of a exible cord or cable to a receptacle outlet or cord connector. 6.3 CLASS 2 LEAD Consists of a factory-made, power-limited cable with a connector at one end. The other end is secured within the housing or enclosure of the RPT. The connector is intended for connection to the Class 2 separable interface. 6.4 CLASS 2 SEPARABLE INTERFACE A separable component containing Class 2 low-voltage connector(s) only (such as Universal Serial Bus (USB) connector(s). 6.