ANSI UL 1653-2006 UL Standard for Safety Electrical Nonmetallic Tubing (Second Edition Reprint with Revisions Through and Including December 23 2014)《电工用非金属管》.pdf

1、UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL UL 1653 Electrical Nonmetallic TubingUL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM ULUL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER

2、 REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL UL Standard for Safety for Electrical Nonmetallic Tubing, UL 1653 Second Edition, Dated May 19, 2006 Summary of Topics The Standard for Electrical Nonmetallic Tubing, UL 1653, is being revised to incorporate the following requirement: 1. New 6

3、3 (2-1/2) Trade Size for Canada Text that has been changed in any manner or impacted by ULs electronic publishing system is marked with a vertical line in the margin. The revised requirements are substantially in accordance with Proposal(s) on this subject dated August 8, 2014. All rights reserved.

4、No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form by any means, electronic, mechanical photocopying, recording, or otherwise without prior permission of UL. UL provides this Standard as is without warranty of any kind, either expressed or implied

5、, including but not limited to, the implied warranties of merchantability or tness for any purpose. In no event will UL be liable for any special, incidental, consequential, indirect or similar damages, including loss of prots, lost savings, loss of data, or any other damages arising out of the use

6、of or the inability to use this Standard, even if UL or an authorized UL representative has been advised of the possibility of such damage. In no event shall ULs liability for any damage ever exceed the price paid for this Standard, regardless of the form of the claim. Users of the electronic versio

7、ns of ULs Standards for Safety agree to defend, indemnify, and hold UL harmless from and against any loss, expense, liability, damage, claim, or judgment (including reasonable attorneys fees) resulting from any error or deviation introduced while purchaser is storing an electronic Standard on the pu

8、rchasers computer system. The requirements in this Standard are now in effect, except for those paragraphs, sections, tables, gures, and/or other elements of the Standard having future effective dates as indicated in the preface. The prior text for requirements that have been revised and that have a

9、 future effective date are located after the Standard, and are preceded by a SUPERSEDED REQUIREMENTS notice. DECEMBER 23, 2014 UL 1653 tr1UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL DECEMBER 23, 2014 UL 1653 tr2 No Text on This PageUL CO

10、PYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL CSA Group CAN/CSA C22.2 No. 227.1-06 Fourth Edition Underwriters Laboratories Inc. UL 1653 Second Edition Electrical Nonmetallic Tubing May 19, 2006 (Title Page Reprinted: December 23, 2014) ANSI/UL

11、 1653-2014 Approved byUL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL Commitment for Amendments This standard is issued jointly by the Canadian Standards Association (operating as “CSA Group”) and Underwriters Laboratories Inc. (UL). Comment

12、s or proposals for revisions on any part of the standard may be submitted to CSA Group or UL at any time. Revisions to this standard will be made only after processing according to the standards development procedures of CSA Group and UL. CSA Group and UL will issue revisions to this standard by mea

13、ns of a revised or additional pages bearing their date of issue. ISBN 1554360013 2006 CSA Group All rights reserved. No part of this publication may be reproduced in any form whatsoever without the prior permission of the publisher. This Standard is subject to review ve years from the date of public

14、ation, and suggestions for its improvement will be referred to the appropriate committee. To submit a proposal for change, please send the following information to inquirescsagroup.org and include “Proposal for change” in the subject line: Standard designation (number); relevant clause, table, and/o

15、r gure number; wording of the proposed change; and rationale for the change. To purchase CSA Group Standards and related publications, visit CSA Groups Online Store at www.shop.csa.ca or call toll-free 1-800-463-6727 or 416-747-4044. Copyright 2014 Underwriters Laboratories Inc. ULs Standards for Sa

16、fety are copyrighted by UL. Neither a printed nor electronic copy of a Standard should be altered in any way. All of ULs Standards and all copyrights, ownerships, and rights regarding those Standards shall remain the sole and exclusive property of UL. This ANSI/UL Standard for Safety consists of the

17、 second edition including revisions through December 23, 2014. The most recent designation of ANSI/UL 1653 as an American National Standard (ANSI) occurred on December 23, 2014. ANSI approval for a standard does not include the Cover Page, Transmittal Pages, Title Page (front and back), or the Prefa

18、ce. Comments or proposals for revisions on any part of the Standard may be submitted to UL at any time. Proposals should be submitted via a Proposal Request in ULs On-Line Collaborative Standards Development System (CSDS) at http:/. To purchase UL Standards, visit Comm 2000 at http:/m- or call toll-

19、free 1-888-853-3503.UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL CONTENTS Preface .5 1 Scope .7 2 Denitions 7 3 General 7 3.1 Components .7 3.2 Reference publications 8 3.3 Units of measurement 10 4 Construction .10 4.1 Compounds 10 4.2 P

20、hysical requirements 11 4.3 Dimensions .11 4.4 End stops 11 5 Performance requirements for ENT 11 5.1 Vertical ame .11 5.2 Bending 11 5.3 Resistance to deection 11 5.4 Impact .12 5.5 Cold bend 12 5.6 Tension 12 5.7 Pull through metal wall studs .12 5.8 Durability of printing .12 5.9 Solvent-attached

21、 tting assembly 12 5.10 Stiffness .12 6 Performance requirements for ttings, mechanically attached .12 6.1 Bending and pull 12 6.2 Flame 13 6.3 Impact .13 6.4 Resistance to deection split-type couplings 13 6.5 Concrete-tightness 13 7 Test methods for ENT 13 7.1 Conditioning 13 7.2 Vertical ame (500

22、W burner) .13 7.3 Flame test in cable trays FT4 (Optional) 14 7.4 Bending 14 7.5 Resistance to deection 14 7.6 Impact .15 7.7 Cold bend 16 7.8 Tension 16 7.9 Pull through metal wall studs .17 7.10 Durability of printing 17 7.11 Solvent-attached tting assembly .18 8 Test methods for ttings, mechanica

23、lly attached .18 8.1 Bending and pull 18 8.2 Flame 19 8.3 Impact .19 8.4 Resistance to deection split-type couplings 19 8.5 Concrete-tightness 20 9 Marking .20 Tables 23 MAY 19, 2006 CSA C22.2 NO. 227.1-06 UL 1653 3UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHO

24、UT PERMISSION FROM UL Figures .24 MAY 19, 2006 CSA C22.2 NO. 227.1-06 UL 1653 4UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL Preface This is the harmonized CSA Group and UL standard for Electrical Nonmetallic Tubing. It is the fourth editi

25、on of CSA C22.2 No. 227.1 and the second edition of UL 1653. This edition of CSA C22.2 No. 227.1 supersedes the previous edition published in 1997. This edition of UL 1653 supersedes the previous edition published in 1997. This harmonized standard has been jointly revised on December 23, 2014. For t

26、his purpose, CSA Group and UL are issuing revision pages dated December 23, 2014. This harmonized standard was prepared by the CSA Group and Underwriters Laboratories Inc. (UL). The efforts and support of the Technical Harmonization Committee 23A ENT Working Group of the Council on the Harmonization

27、 of Electrotechnical Standards of the Nations of the Americas (CANENA) are gratefully acknowledged. This standard is considered suitable for use for conformity assessment within the stated scope of the standard. This standard was reviewed by the CSA Subcommittee on Nonmetallic Conduit, Tubing, and F

28、ittings, under the jurisdiction of the CSA Technical Committee on Wiring Products and the CSA Strategic Steering Committee on Requirements for Electrical Safety, and has been formally approved by the CSA Technical Committee. This standard has been approved as a National Standard of Canada by the Sta

29、ndards Council of Canada (SCC). This standard has been approved by the American National Standards Institute (ANSI) as an American National Standard. Application of Standard Where reference is made to a specic number of samples to be tested, the specied number shall be considered a minimum quantity.

30、 Note: Although the intended primary application of this standard is stated in its scope, it is important to note that it remains the responsibility of the users of the standard to judge its suitability for their particular purpose. Level of harmonization This standard uses the IEC format but is not

31、 based on, nor shall it be considered equivalent to, an IEC standard. This standard is published as an equivalent standard for CSA Group and UL. An equivalent standard is a standard that is substantially the same in technical content, except as follows: Technical national differences are allowed for

32、 codes and governmental regulations as well as those recognized as being in accordance with NAFTA Article 905, for example, because of fundamental climatic, geographical, technological, or infrastructural factors, scientic justication, or the level of protection that the country considers appropriat

33、e. Presentation is word for word except for editorial changes. Reasons for differences from IEC The Technical Harmonization Committee determined the safe use of electrical nonmetallic tubing and ttings is dependent on the design and performance of the raceway and cable systems with which they are in

34、tended to be installed. Signicant investigation is required to assess safety and system compatibility issues that may lead to harmonization of traditional North American nonmetallic tubing and ttings with DECEMBER 23, 2014 CSA C22.2 NO. 227.1-06 UL 1653 5UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FU

35、RTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL those presently addressed in the known IEC standards. The THC agreed such future investigation might be facilitated by completion of harmonization of the North American standards for electrical nonmetallic tubing and ttings. Interpretatio

36、ns The interpretation by the standards development organization of an identical or equivalent standard is based on the literal text to determine compliance with the standard in accordance with the procedural rules of the standards development organization. If more than one interpretation of the lite

37、ral text has been identied, a revision is to be proposed as soon as possible to each of the standards development organizations to more accurately reect the intent. CSA Group Effective Date The effective date for CSA Group will be announced through a CSA Informs or CSA Group Certication Notice. UL E

38、ffective Date As of December 23, 2014 all products Listed or Recognized by UL must comply with the requirements in this standard. A UL effective date is one established by Underwriters Laboratories Inc. and is not part of the ANSI approved standard. DECEMBER 23, 2014 CSA C22.2 NO. 227.1-06 UL 1653 6

39、UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL Electrical Nonmetallic Tubing 1 Scope 1.1 This Standard applies to corrugated electrical nonmetallic tubing (ENT) and mechanically-attached ttings, for use in accordance with C22.1, Canadian El

40、ectrical Code, Part I (CEC), and NFPA 70, National Electrical Code (NEC). These requirements also apply to mechanically-attached ttings integral with an outlet box. 1.2 Products covered by this Standard are intended for use: a) at a maximum continuous operating temperature of 75C (167F); b) at a max

41、imum ambient temperature of 50C (122F); c) in attics provided that the ENT is installed no higher than 900 mm (3 ft) above the bottom of the ceiling joist, and the ENT material is rated minimum 60C (140F); and d) underground (direct burial), in Canada only. 1.3 This Standard does not apply to ttings

42、 that are intended to be joined by solvent cement. Solvent-attached ttings are covered by UL 651 or CSA C22.2 No. 211.2. Solvent-attached ttings integral with an outlet or ush device box are covered by UL 514C or CAN/CSA-C22.2 No. 85. 2 Denitions 2.1 The following denitions apply to this Standard: A

43、dapter a tting used to terminate the ENT at an electrical enclosure. Coupling a tting intended to connect two lengths of ENT. Coupling, Split-Type a two-piece coupling normally used to connect two lengths of ENT after conductors have been pulled. Electrical Nonmetallic Tubing (ENT) a pliable corruga

44、ted raceway of circular cross-section, capable of being bent by hand with a reasonable force, but without other assistance. Fitting, Mechanically Attached a component in the ENT system used to terminate a length of ENT and secured to the ENT by means other than solvent cement. Fitting, Solvent-Attac

45、hed a component in the ENT system used to terminate a length of ENT and secured to the ENT by solvent cement. 3 General 3.1 Components 3.1.1 Except as indicated in Clause 3.1.2, a component of a product covered by this Standard shall comply with all the requirements for that component. A component s

46、hall comply with both the Canadian Standards Association and Underwriters Laboratories Inc. Standards for the component. MAY 19, 2006 CSA C22.2 NO. 227.1-06 UL 1653 7UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL 3.1.2 A component is not re

47、quired to comply with a specic requirement that: a) Involves a feature or characteristic not required in the application of the component in the product covered by this standard, or b) Is superseded by a requirement in this standard. 3.1.3 A component shall be used in accordance with its rating esta

48、blished for the intended conditions of use. 3.1.4 Specic components are incomplete in construction features or restricted in performance capabilities. Such components are intended for use only under limited conditions, such as certain temperatures not exceeding specied limits, and shall be used only

49、 under those specic conditions. 3.2 Reference publications 3.2.1 For undated references to Standards, such reference shall be considered to refer to the latest edition and all revisions to that edition up to the time when this Standard was approved. For dated references to Standards, such reference shall be considered to refer to the dated edition and all revisions published to that edition up to the time the Standard w