1、UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL UL 1715 Fire Test of Interior Finish Material STANDARD FOR SAFETYUL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM ULUL COPYRIGHTED MATERIA
2、L NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL UL Standard for Safety for Fire Test of Interior Finish Material, UL 1715 Third Edition, Dated September 9, 1997 Summary of Topics This revision to ANSI/UL 1715 is being issued to update the title page to reect reaf
3、firmation of ANSI approval. The revisions are substantially in accordance with Proposal(s) on this subject dated February 10, 2017. Text that has been changed in any manner or impacted by ULs electronic publishing system is marked with a vertical line in the margin. All rights reserved. No part of t
4、his publication may be reproduced, stored in a retrieval system, or transmitted in any form by any means, electronic, mechanical photocopying, recording, or otherwise without prior permission of UL. UL provides this Standard as is without warranty of any kind, either expressed or implied, including
5、but not limited to, the implied warranties of merchantability or tness for any purpose. In no event will UL be liable for any special, incidental, consequential, indirect or similar damages, including loss of prots, lost savings, loss of data, or any other damages arising out of the use of or the in
6、ability to use this Standard, even if UL or an authorized UL representative has been advised of the possibility of such damage. In no event shall ULs liability for any damage ever exceed the price paid for this Standard, regardless of the form of the claim. Users of the electronic versions of ULs St
7、andards for Safety agree to defend, indemnify, and hold UL harmless from and against any loss, expense, liability, damage, claim, or judgment (including reasonable attorneys fees) resulting from any error or deviation introduced while purchaser is storing an electronic Standard on the purchasers com
8、puter system. APRIL 27, 2017 UL 1715 tr1UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL APRIL 27, 2017 UL 1715 tr2 No Text on This PageUL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL
9、 SEPTEMBER 9, 1997 (Title Page Reprinted: April 27, 2017) 1 UL 1715 Standard for Fire Test of Interior Finish Material First Edition October, 1989 Second Edition January, 1994 Third Edition September 9, 1997 This ANSI/UL Standard for Safety consists of the Third Edition including revisions through A
10、pril 27, 2017. The most recent designation of ANSI/UL 1715 as a Reaffirmed American National Standard (ANS) occurred on April 27, 2017. ANSI approval for a standard does not include the Cover Page, Transmittal Pages, and Title Page. Comments or proposals for revisions on any part of the Standard may
11、 be submitted to UL at any time. Proposals should be submitted via a Proposal Request in ULs On-Line Collaborative Standards Development System (CSDS) at https:/. ULs Standards for Safety are copyrighted by UL. Neither a printed nor electronic copy of a Standard should be altered in any way. All of
12、ULs Standards and all copyrights, ownerships, and rights regarding those Standards shall remain the sole and exclusive property of UL. COPYRIGHT 2017 UNDERWRITERS LABORATORIES INC. ANSI/UL 1715-2003 (R2017)UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMIS
13、SION FROM UL MARCH 19, 2004 FIRE TEST OF INTERIOR FINISH MATERIAL - UL 1715 2 No Text on This PageUL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL CONTENTS INTRODUCTION 1 Scope .5 2 General 6 2.1 Units of measurement .6 2.2 Undated references
14、 .6 PERFORMANCE 3 General 6 4 Ignition Source .7 5 Fire Test Room Geometry and Construction .7 6 Specimen Mounting .9 7 Protection and Conditioning of Test Assembly 9 8 Fire Test Room Environment .9 8.1 Ventilation 9 8.2 Ambient conditions in test room .10 9 Instrumentation .10 9.1 Ignition source m
15、onitoring thermocouples .10 9.2 Test measurement thermocouples .11 9.3 Visual records .11 10 Test Procedure 11 REPORT 11 General 12 11.1 Materials 12 11.2 Humidity and temperature 12 11.3 Temperature development 12 11.4 Time history of re growth 13 11.5 Specimen conditions .13 APPENDIX A GUIDE TO MO
16、UNTING METHODS A1 Introduction A1 A2 Acoustical Materials and Other Board Materials A4 A3 Batt or Blanket-Type Insulating and Other Flexible Materials .A4 A4 Building Units A4 A5 Coatings or Spray Applied Materials A4 A6 Plastic Materials .A4A A7 Wall Covering Material A5 MARCH 19, 2004 FIRE TEST OF
17、 INTERIOR FINISH MATERIAL - UL 1715 2AUL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL APPENDIX B GUIDE FOR SUPPLEMENTAL INSTRUMENTATION B1 Introduction B1 B1.1 General B1 B1.2 Calorimeters .B1 B2 Thermocouples B1 B2.1 Specication B1 B2.2 Loc
18、ations for room B1 B2.3 Location for doorway B2 B2.4 Location in the collection and dust system .B2 B3 Collection Hood and Exhaust Duct .B3 B3.1 Installation and operation B3 B3.2 Duct Gas Velocity B4 B3.3 Duct oxygen concentration .B4 B3.4 Duct smoke density .B5 B4 Diffused Flame Gas Burner Ignitio
19、n Source B5 B5 Report of Supplemental Data .B6 B5.1 General B6 B5.2 Calculation of the total rate of heat production .B7 OCTOBER 18, 2002 FIRE TEST OF INTERIOR FINISH MATERIAL - UL 1715 2BUL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL OCTOB
20、ER 18, 2002 FIRE TEST OF INTERIOR FINISH MATERIAL - UL 1715 3 No Text on This PageUL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL This page intentionally left blank. APRIL 8, 2008 FIRE TEST OF INTERIOR FINISH MATERIAL - UL 1715 4UL COPYRIGHT
21、ED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL INTRODUCTION 1 Scope 1.1 This test method describes the testing procedures and requirements applicable to the classication of interior nish material assemblies by use of a standardized room re exposure. 1.
22、2 This test method is intended for use in the evaluation of the ammability contribution of wall material assemblies, ceiling material assemblies, or both, exposed to early re growth under specied room re exposure conditions. The effectiveness of re barrier materials as protection for other combustib
23、le materials or components within the assembly is of primary interest for this evaluation. 1.3 Data with respect to surface ammability characteristics of interior nish materials is provided by evaluations in accordance with the Standard for Test for Surface Burning Characteristics of Building Materi
24、als, UL 723, as described in 1.5. 1.4 The results obtained by use of this test method are intended to be used as one element of the total body of data used in the processes of selecting and controlling materials for use in building construction. 1.5 Related classication information for building mate
25、rials and assemblies intended for specic end-uses is promulgated under categorical designations in accordance with specied testing procedures. These classication categories are as follows: a) Surface Burning Characteristics Classication Establishes the comparative burning characteristics of building
26、 materials and assemblies by measurement of ame spread over exposed surfaces and the density of the smoke developed during the re exposure period. This test method is described in the Standard for Test for Surface Burning Characteristics of Building Materials, UL 723. b) Fire Resistance Classication
27、 Establishes hourly re resistance ratings of building assemblies through large-scale re exposures under specic loading conditions. This test method is described in the Standard for Fire Tests of Building Construction and Materials, UL 263. c) Roof-Covering Materials Classication Establishes performa
28、nce measurements for coverings relative to resistance to exterior re spread and penetration. This test method is described in the Standard for Test Methods for Fire Resistance of Roof-Covering Materials, UL 790. d) Roof-Deck Construction Materials Classication Establishes performance measurements fo
29、r roong systems with respect to resistance to the spread-of-ame and damage from underdeck interior re exposure. Information pertaining to the test method used in this classication is published in the General Information section, under Guide TGKX, in Underwriters Laboratories Inc.s Annual Building Ma
30、terials Directory. SEPTEMBER 9, 1997 FIRE TEST OF INTERIOR FINISH MATERIAL - UL 1715 5UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL 2 General 2.1 Units of measurement 2.1.1 Values stated without parentheses are the requirement. Values in p
31、arentheses are explanatory or approximate information. 2.1.1 revised October 18, 2002 2.2 Undated references 2.2.1 Any undated reference to a code or standard appearing in the requirements of this standard shall be interpreted as referring to the latest edition of that code or standard. PERFORMANCE
32、3 General 3.1 A nominal 30 pound (13.6 kg) wood crib is to be used to produce a uniform ame for direct impingement on the walls and ceiling in the corner of an 8 by 12 by 8 foot (2.44 by 3.66 by 2.44 m) high room. The contribution of the wall, ceiling, or both wall and ceiling materials or assemblie
33、s, to re growth is to be dened in terms of: a) The time history of temperature development within the room, b) The time from ignition to ameover, and c) The maximum observed ame progression. The test is to be conducted with natural ventilation to the room provided through a single doorway 2-1/2 by 7
34、 feet (0.76 by 2.13 m) in width and height, respectively. 3.2 During the test the observed surface burning shall not extend to the extremities of the test specimen nor shall ame project through the doorway opening at any time. 3.3 At the conclusion of the test, observations shall show that the combu
35、stive damage, such as burning and charring, of the test materials within the assembly diminishes at increasing distance from the immediate re exposure area. 3.4 A report of the test results shall be prepared as specied in Report, Section 11. OCTOBER 18, 2002 FIRE TEST OF INTERIOR FINISH MATERIAL - U
36、L 1715 6UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL 4 Ignition Source 4.1 The ignition source for the test is to be a wood crib weighing 30 pounds (13.6 kg), having dimensions of 15 by 15 by 15 inches (381 by 381 by 381 mm), and construc
37、ted of 10 tiers of spruce, pine, or r lumber strips. Each strip is to be 15 inches long, and is to have a cross section of trade size 2 by 2 inches nominal 1-1/2 by 1-1/2 inches (38 by 38 mm). Each tier is to consist of ve parallel strips arranged with equal spacing between strips so that the tier d
38、imensions are 15 by 15 inches. Within the crib, the strips in each tier are to lie at right angles to the strips in the tier below. Adjacent tiers are to be fastened to each other by chisel-point staples or 8d nails at each point of contact between strips. Each staple is to have a at top, and the tw
39、o pointed ends each are to be 1-1/4 inch (32 mm) long and on 1 inch (25 mm) centers. 4.2 The crib is to be placed into a curing cell, at a temperature of 120 10F (48.9 5.5C) and 20 5 percent relative humidity, until constant weight is achieved. 4.3 The wood crib is to be removed from the curing cell
40、 not more than 1 hour prior to the start of the test. 4.4 Immediately prior to test, the crib weight is to be adjusted to a nal weight of 30 1 pound (13.61 0.45 kg) by the addition of conditioned strips. 5 Fire Test Room Geometry and Construction 5.1 With the test specimens in place, the interior di
41、mensions of the test room oor are to be 8 feet 1 inch by 12 feet 1 inch (2.4 m 25 mm by 3.66 m 25 mm). The nished ceiling is to be 8 feet 0.5 inch (2.44 m 13 mm) above the oor. There are to be four walls at right angles dening the room (see Figure 5.1). SEPTEMBER 9, 1997 FIRE TEST OF INTERIOR FINISH
42、 MATERIAL - UL 1715 7UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL This is generated text for gtxt. 5.2 The 2-1/2 by 7 foot (0.76 by 2.13 m) doorway is to be in the center of one of the 8 by 8 foot (2.44 by 2.44 m) walls. There are to be n
43、o other wall or ceiling openings. The door frame is to be constructed so that the height and width remain unchanged during the test period to a tolerance of 1 percent. 5.3 There is to be a framed structure resting on a non-combustible oor, with an interior membrane of calcium silicate board of 46 po
44、unds per cubic foot (736 kg/m 3 ) density or equivalent non-combustible board material and 1/2 inch (13 mm) nominal thickness, dening the edges of the ceiling and walls to which the test specimens are attached. Self-supporting panels do not require the frame or calcium silicate board substrate. Figu
45、re 5.1 Room-corner test OCTOBER 18, 2002 FIRE TEST OF INTERIOR FINISH MATERIAL - UL 1715 8UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL 6 Specimen Mounting 6.1 The mounting of the test specimens on the framing or support system shall inclu
46、de backing materials, insulation, and air gaps, or air gaps without backing materials or insulation, as appropriate for the intended application. 6.2 Ceiling material assemblies are to be mounted horizontally to form an 8 by 8 foot (2.44 by 2.44 m) area tangent to the back and side walls. Wall mater
47、ials and assemblies are to be mounted vertically to cover the 8 by 8 foot wall opposite the doorway and 8 feet of the width of one adjacent side wall so as to form an additional 8 by 8 foot wall forming a corner with the back wall as indicated in Figure 5.1. 6.3 Either wall, or ceiling, or both wall
48、 and ceiling material assemblies are to be mounted in the wall-ceiling relationship intended for the anticipated end-use(s). Wall materials to be evaluated alone are to utilize a ceiling fabricated of 1/2 inch (13 mm) thick calcium silicate board supplied in 4 by 8 foot (1.22 by 2.44 m) sheets with
49、a density of 46 pounds per cubic foot (736 kg/m 3 ) or 5/8 inch (15.9 mm) thick gypsum wallboard Type X supplied in 4 by 8 foot sheets, having a density of 42.2 pounds per cubic foot (675 kg/m 3 ), and uncoated; or an equivalent non-combustible board material. Ceiling materials to be evaluated alone are to utilize the specied calcium silicate board or an equivalent non-combustible material on the walls and an uncovered 4 by 8 foot ceiling panel adjacent
copyright@ 2008-2019 麦多课文库（www.mydoc123.com）网站版权所有
备案/许可证编号：苏ICP备17064731号-1