ANSI UL 2115-2015 UL Standard for Safety Processed Solid-Fuel Firelogs (Third Edition).pdf

1、UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL UL 2115 Processed Solid-Fuel FirelogsUL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM ULUL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER

2、 REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL UL Standard for Safety for Processed Solid-Fuel Firelogs, UL 2115 Third Edition, Dated October 2, 2015 Summary of Topics This Third Edition of the Standard for Processed Solid-Fuel Firelogs, ANSI/UL 2115, has been issued as an Editorial update

3、 only. No changes to the requirement have been made. All rights reserved. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form by any means, electronic, mechanical photocopying, recording, or otherwise without prior permission of UL. UL provides thi

4、s Standard as is without warranty of any kind, either expressed or implied, including but not limited to, the implied warranties of merchantability or tness for any purpose. In no event will UL be liable for any special, incidental, consequential, indirect or similar damages, including loss of prots

5、, lost savings, loss of data, or any other damages arising out of the use of or the inability to use this Standard, even if UL or an authorized UL representative has been advised of the possibility of such damage. In no event shall ULs liability for any damage ever exceed the price paid for this Sta

6、ndard, regardless of the form of the claim. Users of the electronic versions of ULs Standards for Safety agree to defend, indemnify, and hold UL harmless from and against any loss, expense, liability, damage, claim, or judgment (including reasonable attorneys fees) resulting from any error or deviat

7、ion introduced while purchaser is storing an electronic Standard on the purchasers computer system. OCTOBER 2, 2015 UL 2115 tr1UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL OCTOBER 2, 2015 UL 2115 tr2 No Text on This PageUL COPYRIGHTED MAT

8、ERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL OCTOBER 2, 2015 1 UL 2115 Standard for Processed Solid-Fuel Firelogs First Edition February, 1999 Second Edition November, 2007 Third Edition October 2, 2015 This ANSI/UL Standard for Safety consists of the Thir

9、d edition. The most recent designation of ANSI/UL 2115 as a Reaffirmed American National Standard (ANS) occurred on June 12, 2014. ANSI approval for a standard does not include the Cover Page, Transmittal Pages and Title Page. Comments or proposals for revisions on any part of the Standard may be su

10、bmitted to UL at any time. Proposals should be submitted via a Proposal Request in ULs On-Line Collaborative Standards Development System (CSDS) at http:/. ULs Standards for Safety are copyrighted by UL. Neither a printed nor electronic copy of a Standard should be altered in any way. All of ULs Sta

11、ndards and all copyrights, ownerships, and rights regarding those Standards shall remain the sole and exclusive property of UL. COPYRIGHT 2015 UNDERWRITERS LABORATORIES INC. ANSI/UL 2115-2010 (R2014)UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FR

12、OM UL OCTOBER 2, 2015 PROCESSED SOLID-FUEL FIRELOGS - UL 2115 2 No Text on This PageUL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL CONTENTS INTRODUCTION 1 Scope .4 2 Units of Measurement .4 3 Undated References 4 PERFORMANCE 4 Aging Test .4

13、 5 Spontaneous Heating Test .4 6 Heat Release Rate Calorimeter Test 5 MARKINGS 7 Firelog Marking and Instructions 6 OCTOBER 2, 2015 PROCESSED SOLID-FUEL FIRELOGS - UL 2115 3UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL INTRODUCTION 1 Scope

14、 1.1 These requirements cover processed solid-fuel relogs that are intended for use as an alternative fuel in factory-built replaces. 2 Units of Measurement 2.1 Values stated without parentheses are the requirement. Values in parentheses are explanatory or approximate information. 3 Undated Referenc

15、es 3.1 Any undated reference to a code or standard appearing in the requirements of this standard shall be interpreted as referring to the latest edition of that code or standard. PERFORMANCE 4 Aging Test 4.1 The processed solid-fuel relog shall remain intact and show no visible signs of degradation

16、 after being subjected to the test described in 4.2 and 4.3. 4.2 Four relogs are to be placed in a full draft circulating air oven at a temperature of 158F (70C) for 60 days. 4.3 The relogs are to be removed from the oven after 60 days and visually examined for degradation such as cracking, brittlen

17、ess, or crumbling. 5 Spontaneous Heating Test 5.1 There shall be no evidence of spontaneous heating of the relog material when tested in accordance with 5.2 5.4. The relogs used for this test shall be previously conditioned as described in the Aging Test, Section 4. 5.2 The apparatus used for the Sp

18、ontaneous Heating Test is to consist of a vertical, cylindrical test chamber, 7 inches (178 mm) in height and 4 inches (102 mm) in diameter, surrounded at the side and bottom by an electrically heated water bath. The test chamber is to be provided with a cover having two air vent tubes and an openin

19、g for introduction of a thermocouple or a maximum registering thermometer. The representative relog is to be contained within the test chamber by a cylinder of wire gauze, 6 inches (152 mm) in height and 1-1/2 inches (38 mm) in diameter. The cylinder is to be concentric with the axis of the test cha

20、mber and annular space through air of 1-1/4 inch (32 mm) is to exist between the cylinder and the wall of the chamber. 5.3 A minimum 2.6-oz (74-g) crumbled segment from the middle of a relog is to be prepared. The segment is to consist of ne particles not larger than 3/8 inch (10 mm) in diameter. Th

21、e segment is to be loosely placed into the cylinder as described in 5.2, with cheesecloth used to close the bottom. The cylinder is then to be placed in the test chamber and a thermocouple is to be inserted at the center of the segment. The cover is then to be placed on the chamber, and the water ba

22、th surrounding the chamber is to be maintained at boiling for a period of 24 hours. OCTOBER 2, 2015 PROCESSED SOLID-FUEL FIRELOGS - UL 2115 4UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL 5.4 A rise in temperature of the segment above the a

23、mbient temperature of the water bath under the conditions of the test indicates spontaneous heating of the product. 6 Heat Release Rate Calorimeter Test 6.1 Using the method described in 6.2 6.4, the Heat Release Rate (HRR) of the processed solid-fuel relog shall be determined. The Peak Average HRR

24、of the relog shall not be greater than 2015 Btu/min (35.4 kW). 6.2 A representative processed solid-fuel relog is to be conditioned to a constant weight at an ambient temperature of 73.4 5.4F (23 3C) and a relative humidity of 50 5 percent. The ambient temperature in the test area is to be greater t

25、han 60F (16C) and the relative humidity is to be less than 75 percent prior to the start of the test. 6.3 The tests are to be conducted under an oxygen consumption calorimeter as shown in Figure 6.1. The representative processed solid-fuel relog is to be placed on a metal stand 36 inches (0.9 m) bel

26、ow the center of the collection hood. The stand is to be constructed of a grid consisting of 1/2-inch (12.7 mm) diameter steel bars, space according to Table 6.1, with side supporting legs. A 5-3/8-inch (140-mm) inside diameter (I.D.) petri dish lled with 3.4 oz (100 ml) of denatured isopropyl alcoh

27、ol is to be used as an ignition source, and is to be located under the center of the relog. 6.4 One processed solid-fuel relog is to be placed on the metal stand in accordance with the manufacturers instructions and the alcohol is to be ignited. The re is to burn until aming combustion ceases. The p

28、eak one minute interval Average HRR and the peak ten minute interval Average HRR are to be calculated using the measurements obtained from the oxygen consumption calorimeter. These measurements are to be taken starting eight minutes after the ignition of the alcohol in the petri dish so that the alc

29、ohol fuel source is completely consumed and the measured Heat Release value is solely that produced by the burning log. Table 6.1 Metal stand bar spacing Firelog length, inches Quantity of supporting bars Supporting bar on-center spacing 15 3 7 inches 9 to 14.75 2 7 inches 4 to 9 2 2 inches less tha

30、n relog length This is generated text for gtxt. OCTOBER 2, 2015 PROCESSED SOLID-FUEL FIRELOGS - UL 2115 5UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL MARKINGS 7 Firelog Marking and Instructions 7.1 Each relog wrapper shall be printed with

31、 the manufacturers name and address, and shall include the following wording: PROCESSED SOLID FUEL FOR USE IN LISTED FACTORY-BUILT FIREPLACES 7.2 Each wrapper shall include the following or equivalent markings and safety instructions: a) Directions For Lighting: 1) Open the replace damper. 2) Pull e

32、nd seams of wrapper outward carefully. (Do not tear wrapper.) 3) Create an air space between the body of the wrapper and the log by carefully pulling outward on the seam. Exception: For relogs that have a grooved surface, item (3) is not required Figure 6.1 Test set-up to determine the heat release

33、rate OCTOBER 2, 2015 PROCESSED SOLID-FUEL FIRELOGS - UL 2115 6UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL 4) Place log (use only one) at the rear of the replace on supporting grate with arrows pointing downward and seam facing room. Ligh

34、t the seam below each arrow. b) CAUTION Risk of Fire: 1) Do not use ammable liquids or gas log lighter to ignite log. 2) Poking or breaking up a burning relog can cause the relog to become extremely ammable. 3) Do not poke burning log with replace tools. Flaming particles may stick to tools. 4) Do n

35、ot place wood or other items on relogs. 5) To extinguish relogs in an emergency use dry chemical re extinguisher or carefully douse re with water. 6) Do not close replace damper until ashes are cool. 7) Do not use in wood stoves or barbecues. 8) Do not use for cooking. c) Safety Instructions: 1) Ope

36、n replace damper before lighting log. 2) Burn relog on supporting grate to rear of replace. 3) Burn ONLY ONE LOG at a time and never add anything to an existing relog re. 4) Close wire mesh protective re screen when burning relog. 5) Never leave any re unattended, nor allow children to play near re. OCTOBER 2, 2015 PROCESSED SOLID-FUEL FIRELOGS - UL 2115 7UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL OCTOBER 2, 2015 PROCESSED SOLID-FUEL FIRELOGS - UL 2115 8 No Text on This Page