ANSI UL 2586-2011 UL Standard for Safety Hose Nozzle Valves (First Edition Reprint with Revisions Through and Including August 22 2014)《软管喷嘴阀安全标准》.pdf

1、UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL UL 2586 Hose Nozzle ValvesUL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM ULUL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTI

2、ON OR DISTRIBUTION WITHOUT PERMISSION FROM UL UL Standard for Safety for Hose Nozzle Valves, UL 2586 First Edition, Dated April 29, 2011 Summary of Topics This revision of ANSI/UL 2586 is being issued to clarify test methods and results and clarify secondary shutoff mechanism. Text that has been cha

3、nged in any manner or impacted by ULs electronic publishing system is marked with a vertical line in the margin. Changes in requirements are marked with a vertical line in the margin and are followed by an effective date note indicating the date of publication or the date on which the changed requir

4、ement becomes effective. The revised requirements are substantially in accordance with Proposal(s) on this subject dated April 4, 2014, June 20, 2014, and June 27, 2014. All rights reserved. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form by an

5、y means, electronic, mechanical photocopying, recording, or otherwise without prior permission of UL. UL provides this Standard as is without warranty of any kind, either expressed or implied, including but not limited to, the implied warranties of merchantability or tness for any purpose. In no eve

6、nt will UL be liable for any special, incidental, consequential, indirect or similar damages, including loss of prots, lost savings, loss of data, or any other damages arising out of the use of or the inability to use this Standard, even if UL or an authorized UL representative has been advised of t

7、he possibility of such damage. In no event shall ULs liability for any damage ever exceed the price paid for this Standard, regardless of the form of the claim. Users of the electronic versions of ULs Standards for Safety agree to defend, indemnify, and hold UL harmless from and against any loss, ex

8、pense, liability, damage, claim, or judgment (including reasonable attorneys fees) resulting from any error or deviation introduced while purchaser is storing an electronic Standard on the purchasers computer system. The requirements in this Standard are now in effect, except for those paragraphs, s

9、ections, tables, gures, and/or other elements of the Standard having future effective dates as indicated in the note following the affected item. The prior text for requirements that have been revised and that have a future effective date are located after the Standard, and are preceded by a SUPERSE

10、DED REQUIREMENTS notice. The following table lists the future effective date with the corresponding item. AUGUST 22, 2014 UL 2586 tr1UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL Future Effective Date References April 30, 2015 Entire stand

11、ard AUGUST 22, 2014 UL 2586 tr2UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL APRIL 29, 2011 (Title Page Reprinted: August 22, 2014) HISTORICAL NOTE Prior to the rst edition, the requirements for the products covered by this standard were i

12、ncluded in the Standard for Valves for Flammable Fluids, UL 842. 1 UL 2586 Standard for Hose Nozzle Valves First Edition April 29, 2011 This ANSI/UL Standard for Safety consists of the First Edition including revisions through August 22, 2014. The most recent designation of ANSI/UL 2586 as an Americ

13、an National Standard (ANSI) occurred on August 22, 2014. ANSI approval for a standard does not include the Cover Page, Transmittal Pages, Title Page, or effective date information. Comments or proposals for revisions on any part of the Standard may be submitted to UL at any time. Proposals should be

14、 submitted via a Proposal Request in ULs On-Line Collaborative Standards Development System (CSDS) at http:/. ULs Standards for Safety are copyrighted by UL. Neither a printed nor electronic copy of a Standard should be altered in any way. All of ULs Standards and all copyrights, ownerships, and rig

15、hts regarding those Standards shall remain the sole and exclusive property of UL. COPYRIGHT 2014 UNDERWRITERS LABORATORIES INC. ANSI/UL 2586-2014UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL AUGUST 22, 2014 HOSE NOZZLE VALVES - UL 2586 2 N

16、o Text on This PageUL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL CONTENTS INTRODUCTION 1 Scope .5 2 General 6 2.1 Components .6 2.2 Units of measurement .6 2.3 Undated references .6 3 Glossary .7 CONSTRUCTION 4 Assembly 8 4.1 General .8 4.

17、2 Hose nozzle valves .8 5 Materials .9 6 Bodies and Covers .10 7 Diaphragms .12 8 Springs .12 9 Operating Mechanisms .12 PERFORMANCE 10 General 12 11 Deformation Test .13 12 External Leakage Test 14 13 Seat Leakage Test 14 14 Hose Nozzle Valve Guard Strength Test .15 15 Operation Test .16 15.1 Autom

18、atic hose nozzle valve .16 15.2 Bellows Secondary Shut Off Operation 17 16 Pull Test .17 17 Sensitivity Test .17 18 Hose Nozzle Endurance Test 18 19 Bellows Secondary Shut Off Operation Test 18A 20 Visible Discharge Indicator Tests 18A 20.1 Thermal shock test 18A 20.2 Drop test .18A 21 Hydrostatic S

19、trength Test .18B 22 Electrical Continuity Test .18B 23 Salt Spray Test .18B 24 Moist Ammonia-Air Stress Cracking Test 21 25 Tests of Synthetic Rubber Parts 21 25.1 General .21 25.2 Volume change test 22 25.3 Weight loss test 22 25.4 Accelerated aging test 23 26 Marking Adhesion Test 23 AUGUST 22, 2

20、014 HOSE NOZZLE VALVES - UL 2586 3UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL MANUFACTURING AND PRODUCTION TESTS 27 General 23 INSTALLATION INSTRUCTIONS 28 General 24 MARKING 29 General 24 APRIL 29, 2011 HOSE NOZZLE VALVES - UL 2586 4UL

21、COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL INTRODUCTION 1 Scope 1 effective April 30, 2015 1.1 These requirements cover hose nozzle valves that are intended to be used for the control of ammable and combustible liquids. They are of the typ

22、e used in motor fuel dispensing equipment. Hose nozzle valves covered by this standard are for use with ammable uids which are handled at temperatures within the range of minus 29C (minus 20F) to 52C (125F) and an operating pressure of minimum 50 psi (350 kPa). 1.2 These requirements cover hose nozz

23、le valves of the manually operated and automatic pressure operated type. When they form a part of an assembly which provides for additional functions or service, the requirements are outside the scope of these requirements. 1.3 These requirements do not cover the following: a) Hose nozzle valves for

24、 handling liquids under cryogenic conditions. b) Hose nozzle valves for general renery service, offshore and pipe line terminals, natural gas processing plants, gas distribution systems, petrochemical processing facilities, or the like. c) Hose nozzle valves operated wholly or partially by electrici

25、ty or battery. 1.4 For hose nozzle valves intended to be used with gasoline/ethanol blends with nominal ethanol concentrations above 10%, refer to Outline of Investigation for Gasoline and Gasoline/Ethanol Blends with Nominal Ethanol Concentrations up to 85 Percent (E0 - E85), UL 87A, for additional

26、 requirements. Revised 1.4 effective April 30, 2015 1.5 Refer to Outline of Investigation, UL 87B, for additional requirements for Diesel Fuel, Biodiesel Fuel, Diesel/Biodiesel Blends with Nominal Biodiesel Concentrations Up to 20 Percent (B20), Kerosene, and Fuel Oil. 1.6 Requirements for the insta

27、llation and use of these dispensing devices are included in the Code for Motor Fuel Dispensing Facilities and Repair Garages, NFPA 30A. MARCH 15, 2012 HOSE NOZZLE VALVES - UL 2586 5UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL 2 General 2

28、effective April 30, 2015 2.1 Components 2.1.1 Except as indicated in 2.1.2, a component of a product covered by this standard shall comply with the requirements for that component. 2.1.2 A component is not required to comply with a specic requirement that: a) Involves a feature or characteristic not

29、 required in the application of the component in the product covered by this standard, or b) Is superseded by a requirement in this standard. 2.1.3 A component shall be used in accordance with its rating established for the intended conditions of use. 2.1.4 Specic components are incomplete in constr

30、uction features or restricted in performance capabilities. Such components are intended for use only under limited conditions, such as certain temperatures not exceeding specied limits, and shall be used only under those specic conditions. 2.1.5 A hose nozzle valve with an integral swivel shall be a

31、dditionally evaluated to the Electrical-Continuity and Operation Tests in the Standard for Emergency Breakaway Fittings, Swivel Connectors and Pipe-Connection Fittings for Petroleum Products and LP-Gas, UL 567. The force is to be applied at the point on the swivel farthest from the joint. When neces

32、sitated by the swivel construction, this test is to be conducted on additional samples of the swivel with the load applied on the opposite side of the plane of rotation. See UL 567, Figures 15.1 15.3 for examples. 2.2 Units of measurement 2.2.1 When a value for measurement is followed by a value in

33、other units in parentheses, the rst stated value is the requirement. 2.3 Undated references 2.3.1 Any undated reference to a code or standard appearing in the requirements of this standard shall be interpreted as referring to the latest edition of that code or standard. APRIL 29, 2011 HOSE NOZZLE VA

34、LVES - UL 2586 6UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL 3 Glossary 3 effective April 30, 2015 3.1 FLAMMABLE AND COMBUSTIBLE FLUIDS Diesel, gasoline, and kerosene not in excess of 50 pounds per square inch (psi) (344.8 kPa). The fuels

35、 are formulated in accordance with Regulation of Fuels and Fuel Additives, 40CFR80, and the following: a) Gasoline formulated in accordance with the Standard Specication for Automotive Spark- Ignition Engine Fuel, ASTM/ANSI D4814; b) Gasoline/ethanol blends at levels designated as gasohol (E10) or l

36、ess formulated in accordance with ASTM/ANSI D4814, when blended with denatured fuel ethanol formulated in accordance with the Standard Specication for Denatured Fuel Ethanol for Blending with Gasolines for Use as Automotive Spark-Ignition Engine Fuel, ASTM/ANSI D4806; c) Diesel fuel formulated in ac

37、cordance with the Standard Specication for Diesel Fuel Oils, ASTM/ANSI D975; d) Kerosene formulated in accordance with the Standard Specication for Kerosine, ASTM/ ANSI D3699; and e) Fuel oil (heating fuel) formulated in accordance with the Standard Specication for Fuel Oils, ASTM D396. 3.2 HOSE NOZ

38、ZLE VALVE, AUTOMATIC A hose nozzle valve which is held open during the entire lling operation. It may be held open by manual force or by an integral hold-open or latching device. It incorporates a mechanism that shuts off the ow of liquid during refueling operations to prevent overow from the ll ope

39、ning when liquid reaches a predetermined point on the spout. 3.3 HOSE NOZZLE VALVES A self-closing device designed to control the ow of ammable and combustible liquids at an operating pressure of minimum 50 psi (345 kPa). It is intended for use at the outlet end of a hose for dispensing ammable liqu

40、ids. 3.4 HOSE NOZZLE VALVE, MANUALLY OPERATED A hose nozzle valve that is manually held open during the entire lling operation and closes only upon release of the manual force. 3.5 HOSE NOZZLE VALVE, VAPOR RECOVERY A system constructed to capture vapors displaced during lling operations. The vapors

41、are not processed during the course of this activity. a) Assist Nozzle A vacuum or pump is used to draw the vapors back to tank. b) Balance Nozzle Displacement of vapors from tank being ll forces the vapor back into the storage tank. 3.6 SEALS, DYNAMIC A seal that is subject to mechanical movement o

42、r other applied forces that result in movement or exing of the seal under normal use conditions. 3.7 SEALS, STATIC A seal that is not subject to mechanical movement or other applied forces other than compressing forces that are applied during installation, after which, the seal is held in place duri

43、ng normal use conditions. APRIL 29, 2011 HOSE NOZZLE VALVES - UL 2586 7UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL CONSTRUCTION 4 Assembly 4 effective April 30, 2015 4.1 General 4.1.1 A hose nozzle valve shall include all of the componen

44、ts required for its intended function and installation. 4.1.2 A seat disc shall be attached to its poppet or holder or otherwise assembled so as to prevent it from becoming dislocated under service conditions as determined by the Hose Nozzle Endurance Test, Section 18. The means to secure the disc s

45、hall not rely upon cement or adhesive. 4.1.3 A brazing material used for joining liquid conning parts of a valve shall have a melting point (solidus temperature) of minimum 538C (1000F). 4.2 Hose nozzle valves 4.2.1 A hose nozzle valve shall be of the manually-operated or of the automatic type. A ma

46、nually-operated valve requires the valve to be manually held open during the entire lling operation without the aid of hold-open devices or latches, but is capable of closing automatically. An automatic valve requires the valve to: a) Be manually opened, but is capable of being held open during the

47、lling operation by a latch or other device and b) Is provided with automatic closing features. Exception: A hose nozzle valve for use in salt water or boat yard environments shall be of the automatic closing type without a latch-open device. 4.2.2 Automatic hose nozzle valves equipped with an integr

48、al hold open or latching device shall be so designed that, if left in the latched position after the ow has been stopped by means other than the automatic feature of the hose nozzle, it shall automatically unlatch when it is returned to the dispenser, See Automatic hose nozzle valve, 15.1.2. NOTE: T

49、his includes hose nozzle valves that close with a no pressure/no ow mechanism, as well as interlock hose nozzles valves that unlatch when removed from car ll pipe or when hung on the dispenser. 4.2.3 A hose nozzle valve shall be of the normally closed type. It shall be self-closing upon the manual or automatic release of the operating lever. 4.2.4 A guard shall be provided to guide or protect the free end of an operating lever and to prevent opening of the valve or damage to