ANSI UL 567A-2015 UL Standard for Safety Emergency Breakaway Fittings Swivel Connectors and Pipe-Connection Fittings for Gasoline and Gasoline Ethanol Blends with Nominal Ethanol C.pdf

1、UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL UL 567A Emergency Breakaway Fittings, Swivel Connectors and Pipe-Connection Fittings for Gasoline and Gasoline/Ethanol Blends with Nominal Ethanol Concentrations up to 85 Percent (E0 E85)UL COP

2、YRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM ULUL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL UL Standard for Safety for Emergency Breakaway Fittings, Swivel Connectors and Pipe-Connectio

3、n Fittings for Gasoline and Gasoline/Ethanol Blends with Nominal Ethanol Concentrations up to 85 Percent (E0 E85), UL 567A First Edition, Dated March 5, 2015 Summary of Topics This revision of ANSI/UL 567A relocates 9.1 to the scope section and revises the Moist Ammonia-Air Stress Cracking Test. The

4、 revised requirements are substantially in accordance with Proposal(s) on this subject dated May 1, 2015. Text that has been changed in any manner or impacted by ULs electronic publishing system is marked with a vertical line in the margin. All rights reserved. No part of this publication may be rep

5、roduced, stored in a retrieval system, or transmitted in any form by any means, electronic, mechanical photocopying, recording, or otherwise without prior permission of UL. UL provides this Standard as is without warranty of any kind, either expressed or implied, including but not limited to, the im

6、plied warranties of merchantability or tness for any purpose. In no event will UL be liable for any special, incidental, consequential, indirect or similar damages, including loss of prots, lost savings, loss of data, or any other damages arising out of the use of or the inability to use this Standa

7、rd, even if UL or an authorized UL representative has been advised of the possibility of such damage. In no event shall ULs liability for any damage ever exceed the price paid for this Standard, regardless of the form of the claim. Users of the electronic versions of ULs Standards for Safety agree t

8、o defend, indemnify, and hold UL harmless from and against any loss, expense, liability, damage, claim, or judgment (including reasonable attorneys fees) resulting from any error or deviation introduced while purchaser is storing an electronic Standard on the purchasers computer system. JUNE 17, 201

9、5 UL 567A tr1UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL JUNE 17, 2015 UL 567A tr2 No Text on This PageUL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL March 5, 2015 (Title Page R

10、eprinted: June 17, 2015) 1 UL 567A Standard for Emergency Breakaway Fittings, Swivel Connectors and Pipe- Connection Fittings for Gasoline and Gasoline/Ethanol Blends with Nominal Ethanol Concentrations up to 85 Percent (E0 E85) Prior to the rst edition, the requirements for the products covered by

11、this standard were included in the Outline of Investigation for Emergency Breakaway Fittings, Swivel Connectors and Pipe-Connection Fittings for Gasoline and Gasoline/Ethanol Blends with Nominal Ethanol Concentrations up to 85 Percent (E0 E85), UL 567A. First Edition March 5, 2015 This ANSI/UL Stand

12、ard for Safety consists of the First Edition including revisions through June 17, 2015. The most recent designation of ANSI/UL 567A as an American National Standard (ANSI) occurred on June 17, 2015. ANSI approval for a standard does not include the Cover Page, Transmittal Pages, Title Page, or effec

13、tive date information. Comments or proposals for revisions on any part of the Standard may be submitted to UL at any time. Proposals should be submitted via a Proposal Request in ULs On-Line Collaborative Standards Development System (CSDS) at http:/. ULs Standards for Safety are copyrighted by UL.

14、Neither a printed nor electronic copy of a Standard should be altered in any way. All of ULs Standards and all copyrights, ownerships, and rights regarding those Standards shall remain the sole and exclusive property of UL. COPYRIGHT 2015 UNDERWRITERS LABORATORIES INC. ANSI/UL 567A-2015UL COPYRIGHTE

15、D MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL JUNE 17, 2015 UL 567A 2 No Text on This PageUL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL CONTENTS INTRODUCTION 1 Scope 4A 2 General 4B 2.1 Compo

16、nents 4B 2.2 Units of measurement .4B 2.3 Undated references .4B 3 Glossary .5 CONSTRUCTION 4 General 8 5 Materials .8 5.1 Metallic materials .8 5.2 Nonmetallic materials 11 5.3 Casting impregnation materials 13 5.4 Internal parts .13 5.5 Blending options 14 6 Swivel Connectors and Emergency Breakaw

17、ay Fittings .14 7 Pipe-Connecting Fittings 14 8 End Connections 16 9 Hose Assemblies 18 PERFORMANCE 10 General 18 11 Long Term Exposure Test .20 11.1 General .20 11.2 Samples 20 11.3 Method .21 11.4 Results .21 12 Electrical-Continuity Test 22 12.1 General .22 12.2 Electrical continuity measurement

18、22 12.3 Electrical continuity alternate method .22 13 External Leakage Test 22 14 Seat Leakage Test 23 15 Operation Test .23 16 Endurance Test 25 17 Abuse Test 26 18 Drop Test 27 19 Hydrostatic Strength Test 27 20 Pull Test .28 20.1 Pipe-connecting tting 28 20.2 Emergency breakaway tting 28 21 Marki

19、ng Adhesion Test 29 22 Moist Ammonia-Air Stress Cracking Test 29 23 Blending Cycling Test .30 MANUFACTURING AND PRODUCTION JUNE 17, 2015 UL 567A 3UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL 24 General 31 INSTALLATION AND OPERATING INSTRU

20、CTIONS 25 General 31 MARKING 26 General 31 SUPPLEMENT SA - Test Fluids SA.1 Details .SA1 JUNE 17, 2015 UL 567A 4UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL INTRODUCTION 1 Scope 1.1 These requirements cover emergency breakaway ttings, swi

21、vel connectors and pipe-connecting ttings of the threadless compression type. Connectors and ttings covered by these requirements are intended only for the following services. 1.2 A swivel connector is either a hose swivel or joint swivel. The swivel connector will allow radial movement and shall be

22、 constructed for use with the uids shown in 1.4. 1.3 An emergency breakaway tting is used between the outlet of the dispensing device and the hose nozzle valve and separates in the event that the coupling is subjected to an excessive pull force to safeguard against abnormally excessive pull force on

23、 the hose assembly and dispenser and prevent loss of liquid. An emergency breakaway tting shall be constructed for use with the uids shown in 1.4. The ttings shall be of the single-break or reconnectable type. 1.4 Emergency breakaway ttings, swivel connectors, and pipe-connecting ttings are intended

24、 for use with one or more of the following as applicable: a) Gasoline formulated in accordance with the Standard Specication for Automotive Spark- Ignition Fuel, ASTM D4814; b) Gasoline/ethanol blends with nominal ethanol concentrations up to 25 percent ethanol (E25), consisting of gasoline formulat

25、ed in accordance with the Standard Specication for Automotive Spark-Ignition Fuel, ASTM D4814, when blended with denatured fuel ethanol formulated to be consistent with the Standard Specication for Denatured Fuel Ethanol for Blending with Gasolines for Use as Automotive Spark-Ignition Engine Fuel, A

26、STM D4806; or c) Gasoline/ethanol blends with nominal ethanol concentrations above 25 percent formulated in accordance with the Standard Specication in item (b) or formulated in accordance with the Standard Specication for Ethanol Fuel Blends for Flexible-Fuel Automotive Spark-Ignition Engines, ASTM

27、 D5798. 1.5 Requirements for the installation and use of dispensing equipment handling the fuels described in 1.4 are included in the Flammable and Combustible Liquids Code, ANSI/NFPA 30, and the Code for Motor Fuel Dispensing Facilities and Repair Garages, ANSI/NFPA 30A. 1.6 These requirements do n

28、ot cover devices intended for use with diesel, biodiesel, diesel/biodiesel blends, kerosene or fuel oil, which are covered under the Standard for Emergency Breakaway Fittings, Swivel Connectors, and Pipe-Connection Fittings for Diesel Fuel, Biodiesel Fuel, Diesel/Biodiesel Blends with Nominal Biodie

29、sel Concentrations up to 20 Percent (B20), Kerosene, and Fuel Oil, UL 567B. 1.7 These requirements do not cover devices intended for use with anhydrous ammonia or LP-Gas, which as covered under the Standard for Emergency Breakaway Fittings, Swivel Connectors, and Pipe-Connection Fittings for Petrole

30、um Products and LP-Gas, UL 567. JUNE 17, 2015 UL 567A 4AUL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL 1.8 A hose assembly provided with a swivel connector or emergency breakaway tting for use with fuels anticipated by these requirements sh

31、all comply with the applicable requirements in the Standard for Hose and Hose Assemblies for Gasoline and Gasoline/Ethanol Blends with Nominal Ethanol Concentrations up to 85 Percent (E0 E85), UL 330A. 2 General 2.1 Components 2.1.1 Except as indicated in 2.1.2, a component of a product covered by t

32、his standard shall comply with the requirements for that component. 2.1.2 A component is not required to comply with a specic requirement that: a) Involves a feature or characteristic not required in the application of the component in the product covered by this standard, or b) Is superseded by a r

33、equirement in this standard. 2.1.3 A component shall be used in accordance with its rating established for the intended conditions of use. 2.1.4 Specic components are incomplete in construction features or restricted in performance capabilities. Such components are intended for use only under limite

34、d conditions, such as certain temperatures not exceeding specied limits, and shall be used only under those specic conditions. 2.2 Units of measurement 2.2.1 Values stated without parentheses are the requirement. Values in parentheses are explanatory or approximate information. 2.3 Undated reference

35、s 2.3.1 Any undated reference to a code or standard appearing in the requirements of this standard shall be interpreted as referring to the latest edition of that code or standard. JUNE 17, 2015 UL 567A 4BUL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISS

36、ION FROM UL 3 Glossary 3.1 For the purpose of this standard, the following denitions apply. 3.2 BLENDING OPTION Dispensing devices may be provided with an option that blends two specic fuels into one fuel to be dispensed. This blending occurs at the dispenser level and can be in two forms: a) Fixed

37、blending Blending at the dispenser level that blends two specic fuels into one fuel to be dispensed, and that fuel to be dispensed is xed. For example, xed blending includes blend options where gasoline and denatured fuel ethanol can be blended to achieve E85, which is the actual dispensed fuel. b)

38、Variable blending Blending at the dispenser level that blends two specic fuels into the fuel to be dispensed, but the fuel to be dispensed can be any of a number of previously set points. For example, variable blending includes blend options where gasoline and E85 can be blended to achieve E40, E60,

39、 and E85 as the actual dispensed fuel. 3.3 FITTING, PIPE-CONNECTING A tting of the threadless compression seal-ring type for use in the assembly of dispensing devices to facilitate connection of piping or tubing. These ttings shall be made in the straight coupling style, as well as in the tee, ell,

40、reducer, adapter, and other styles. JUNE 17, 2015 UL 567A 5UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL JUNE 17, 2015 UL 567A 6 No Text on This PageUL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PE

41、RMISSION FROM UL 3.4 FITTING, RECONNECTABLE TYPE An emergency breakaway tting designed such that upon separation it is intended to be reconnected and reused when it is not damaged. 3.5 FITTING, SINGLE-BREAK TYPE An emergency breakaway tting that, upon separation, is not intended to be reconnected an

42、d reused. 3.6 GASOLINE/ETHANOL BLENDS Blended fuels composed of a gasoline component and an ethanol component. The numerical value corresponding to the ethanol component determines the blend rating (such as E85 for 85% ethanol, 15% gasoline). 3.7 HOSE SWIVEL A swivel connector with one end attached

43、to a hose and the other end to an appurtenance. The hose swivel will allow radial movement of the hose and/or appurtenance to prevent the hose from twisting or having torsional stress. 3.8 PRESSURE INDICATING DEVICE As used herein, the pressure indicating device means one of the following: a) An ana

44、log gauge having a pressure range such that the test pressure is between 30 and 70 percent of the maximum scale reading of the gauge; b) A digital pressure transducer, or other digital gauge, that is calibrated over a range of pressure that includes the test pressure; or c) Other device that is equi

45、valent to the devices in (a) or (b). 3.9 SEALS, DYNAMIC A seal that is subject to mechanical movement or other applied forces that result in movement or exing of the seal under normal use conditions. 3.10 SEALS, STATIC A seal that is not subject to mechanical movement or other applied forces other t

46、han compressing forces that are applied during installation, after which, the seal is held in place during normal use conditions. 3.11 SWIVEL CONNECTOR A type of swivel categorized as either a hose swivel or swivel joint. 3.12 SWIVEL JOINT A swivel connector installed in a piping system with at leas

47、t one end attached to a rigid pipe or other appurtenance that is rmly affixed. The swivel joint will allow radial movement of the pipe or other appurtenance attached to the swivel to prevent torsional stress. MARCH 5, 2015 UL 567A 7UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR D

48、ISTRIBUTION WITHOUT PERMISSION FROM UL CONSTRUCTION 4 General 4.1 A connector or tting shall be constructed for an operating pressure of not less than 50 pounds per square inch gauge (psig) (340 kPa) for the uid conning portion of the device and 0.5 psig (3.45 kPa) for the vapor conning portion of t

49、he device, when provided, and an ultimate rupture pressure of not less than ve times the design pressure. 4.2 An emergency breakaway tting shall be constructed to separate in the event that the coupling is subjected to a pull force not less than 100 pounds (445 N), and not to exceed 350 pounds (1557 N). 5 Materials 5.1 Metallic materials 5.1.1 General 5.1.1.1 A metallic part, in contact with the fuels anticipated by these requirements, shall be resistant to th