ANSI UL 60745-2-2-2004 UL Standard for Safety Hand-Held Motor-Operated Electric Tools - Safety - Part 2-2 Particular Requirements for Screwdrivers and Impact Wrenches (Second Editi.pdf

1、UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL UL 60745-2-2 Hand-Held Motor-Operated Electric Tools Safety Part 2-2: Particular Requirements for Screwdrivers and Impact WrenchesUL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION

2、 OR DISTRIBUTION WITHOUT PERMISSION FROM ULUL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL UL Standard for Safety for Hand-Held Motor-Operated Electric Tools Safety Part 2-2: Particular Requirements for Screwdrivers and Impact Wrenches, UL 6

3、0745-2-2 Second Edition, Dated March 26, 2004 Summary of Topics The revisions dated October 31, 2014 are being issued to incorporate the following proposals and to reect the latest ANSI approval date for UL 60745-2-2. 1. Addition Of National Difference Clauses To Specify Ratchet Drivers In The Scope

4、 Of The Standard And To Clarify Test Requirements As They Apply To Ratchet Drivers Note: Annex 2.DVL was originally provided as supplemental information and was considered editorial, Type DE. The annex is now considered no longer necessary, and has been deleted. Text that has been changed in any man

5、ner or impacted by ULs electronic publishing system is marked with a vertical line in the margin. All rights reserved. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form by any means, electronic, mechanical photocopying, recording, or otherwise wi

6、thout prior permission of UL. UL provides this Standard as is without warranty of any kind, either expressed or implied, including but not limited to, the implied warranties of merchantability or tness for any purpose. In no event will UL be liable for any special, incidental, consequential, indirec

7、t or similar damages, including loss of prots, lost savings, loss of data, or any other damages arising out of the use of or the inability to use this Standard, even if UL or an authorized UL representative has been advised of the possibility of such damage. In no event shall ULs liability for any d

8、amage ever exceed the price paid for this Standard, regardless of the form of the claim. Users of the electronic versions of ULs Standards for Safety agree to defend, indemnify, and hold UL harmless from and against any loss, expense, liability, damage, claim, or judgment (including reasonable attor

9、neys fees) resulting from any error or deviation introduced while purchaser is storing an electronic Standard on the purchasers computer system. The requirements in this Standard are now in effect, except for those paragraphs, sections, tables, gures, and/or other elements of the Standard having fut

10、ure effective dates as indicated in the preface. The prior text for requirements that have been revised and that have a future effective date are located after the Standard, and are preceded by a SUPERSEDED REQUIREMENTS notice. OCTOBER 31, 2014 UL 60745-2-2 tr1UL COPYRIGHTED MATERIAL NOT AUTHORIZED

11、FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL OCTOBER 31, 2014 UL 60745-2-2 tr2 No Text on This PageUL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL CSA Group CAN/CSA-C22.2 No. 60745-2-2-04 Second Edition (IEC 60745-2-2:

12、2003, MOD) Underwriters Laboratories Inc. UL 60745-2-2 Second Edition Hand-Held Motor-Operated Electric Tools Safety Part 2-2: Particular Requirements for Screwdrivers and Impact Wrenches March 26, 2004 (Title Page Reprinted: October 31, 2014) This national standard is based on publication IEC 60745

13、-2-2, Second Edition (2003). This amendment is an adoption of IEC Amendment 1(2008) to publication IEC 60745-2-2, Second Edition (2005). ANSI/UL 60745-2-2-2014 Approved byUL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL Commitment for Amendme

14、nts This standard is issued jointly by the Canadian Standards Association (operating as “CSA Group”) and Underwriters Laboratories Inc. (UL). Comments or proposals for revisions on any part of the standard may be submitted to CSA Group or UL at anytime. Revisions to this standard will be made only a

15、fter processing according to the standards development procedures of CSA Group and UL. CSA Group and UL will issue revisions to this standard by means of a new edition or revised or additional pages bearing their date of issue. ISBN 1-55397-464-6 2004 CSA Group All rights reserved. No part of this p

16、ublication may be reproduced in any form whatsoever without the prior permission of the publisher. Copyright 2014 Underwriters Laboratories Inc. Comments or proposals for revisions on any part of the Standard may be submitted to UL at any time. Proposals should be submitted via a Proposal Request in

17、 ULs On-Line Collaborative Standards Development System (CSDS) at http:/. The most recent designation of ANSI/UL 60745-2-2 as a Reaffirmed American National Standard (ANS) occurred on October 31, 2014. The ANSI approval for this standard does not include the Cover Page, Transmittal Pages, Title Page

18、, Preface Page, National Difference Page or IEC Foreword. Comments or proposals for revisions on any part of the Standard may be submitted to UL at any time. Proposals should be submitted via a Proposal Request in ULs On-Line Collaborative Standards Development System (CSDS) at http:/. ULs Standards

19、 for Safety are copyrighted by UL. Neither a printed nor electronic copy of a Standard should be altered in any way. All of ULs Standards and all copyrights, ownerships, and rights regarding those Standards shall remain the sole and exclusive property of UL.UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR

20、 FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL CONTENTS Preface .5 FOREWORD 8 1 Scope 11 2 Normative references .11 3 Terms and Denitions 11 4 General requirements 11 5 General conditions for the tests 11 6 Void 12 7 Classication 12 8 Marking and instructions 12 9 Protection agains

21、t access to live parts 12 10 Starting 12 11 Input and current .12 12 Heating 12 13 Leakage current 13 14 Moisture resistance .13 15 Electric strength 13 16 Overload protection of transformers and associated circuits 13 17 Endurance .14 18 Abnormal operation 14A 19 Mechanical hazards .14A 20 Mechanic

22、al strength .14A 21 Construction 14A 22 Internal wiring .14A 23 Components 14B 24 Supply connection and external exible cords .14B 25 Terminals for external conductors .14B 26 Provision for earthing 14B 27 Screws and connections .14B 28 Creepage distances, clearances and distances through insulation

23、 .14B 29 Resistance to heat, re and tracking .14B 30 Resistance to rusting 14B 31 Radiation, toxicity and similar hazards .14B OCTOBER 31, 2014 CAN/CSA-C22.2 NO. 60745-2-2-04 UL 60745-2-2 3UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL Anne

24、xes Annex K Battery Tool and Battery Packs Annex L Battery Tools and Battery Packs Provided with Mains Connection or Non-Isolated Sources Annex 2.DVL List of National Differences Bibliography MARCH 26, 2004 CAN/CSA-C22.2 NO. 60745-2-2-04 UL 60745-2-2 4UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTH

25、ER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL Preface This is the common CSA and UL standard for hand-held motor-operated electric tools. It is the second edition of CAN/CSA-C22.2 No. 60745-2-2 and the second edition of UL 60745-2-2. This standard is based on IEC 60745-2-2, second editi

26、on. The rst edition of this standard was designated CAN/CSA-C22.2 No. 745-2-2/UL 745-2-2. This Standard CAN/CSA-C22.2 No. 60745-2-2/UL 60745-2-2, second edition, supersedes: a) the rst edition CAN/CSA-C22.2 No. 745-2-2/UL 745-2-2 published in 1995; and b) CAN/CSA-C22.2 No. 745-4-2/UL 745-4-2, (requi

27、rements for battery tools and battery packs are now incorporated into the requirements of CAN/CSA-C22.2 No. 60745-2-2, second edition, and UL 60745-2-2, second edition). The standard number has been aligned to correspond with the equivalent IEC 60745-2-2 standard. This common standard was prepared b

28、y the Canadian Standards Association (CSA) and Underwriters Laboratories Inc. (UL). This standard was reviewed by the CSA Subcommittee on Portable Electric Tools, under the jurisdiction of the CSA Technical Committee on Consumer and Commercial Products and the CSA Strategic Steering Committee on Req

29、uirements for Electrical Safety, and has been formally approved by the CSA Technical Committee. This standard has been approved as a National Standard of Canada by the Standards Council of Canada and has been approved by the American National Standards Institute (ANSI) as an American National Standa

30、rd. Note: Although the intended primary application of this standard is stated in its scope, it is important to note that it remains the responsibility of the users of the standard to judge its suitability for their particular purpose. A UL standard is current only if it incorporates the most recent

31、ly adopted revisions, all of which are itemized on the transmittal notice that accompanies the latest set of revised requirements. Where reference is made to a specic number of samples to be tested, the specied number shall be considered a minimum quantity. Level of harmonization This standard adopt

32、s the IEC text with national differences. This standard is published as an equivalent standard for CSA and UL. An equivalent standard is a standard that is substantially the same in technical content, except as follows: Technical national differences are allowed for codes and governmental regulation

33、s as well as those recognized as being in accordance with NAFTA Article 905, for example because of fundamental climatic, geographical, technological, or infrastructural factors, scientic justication, or the level of protection that the country considers appropriate. Presentation is word for word ex

34、cept for editorial changes. MARCH 26, 2004 CAN/CSA-C22.2 NO. 60745-2-2-04 UL 60745-2-2 5UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL Interpretations The interpretation by the standards development organization of an identical or equivalen

35、t standard is based on the literal text to determine compliance with the standard in accordance with the procedural rules of the standards development organization. If more than one literal interpretation has been identied, a revision is to be proposed as soon as possible to each of the standards de

36、velopment organizations to more accurately reect the intent. CSA effective date The effective date for CSA International will be announced through CSA Informs or a CSA certication notice. UL effective date UL 60745-2-2, second edition, was effective on October 31, 2012. A UL effective date is one es

37、tablished by Underwriters Laboratories Inc. and is not part of the ANSI approved standard. General The previous version of CAN CSA C22.2 No. 60745-2-2-04/UL 60745-2-2 included a national difference to IEC Clause 8.12.1. The national difference was deleted in this version of CAN CSA C22.2 No. 60745-2

38、-2-04/UL 60745-2-2. Annex 2.DVL was originally provided as supplemental information and was considered editorial, Type DE. The annex is now considered no longer necessary, and has been deleted. There are ve types of National Differences as noted below. The difference type is noted on the rst line of

39、 the National Difference in the standard. The standard may not include all types of these National Differences. National Differences from the text of the International Electrotechnical Commission (IEC) publication 60745-2-2 (Hand-Held Motor-Operated Electric Tools Safety Part 2-2: Particular Require

40、ments for Screwdrivers and Impact Wrenches) are indicated by the following notation: DR These are National Differences based on the national regulatory requirements. D1 These are National Differences which are based on basic safety principles and requirements, elimination of which would compromise s

41、afety for consumers and users of products. D2 These are national differences from IEC requirements based on existing safety practices. These requirements reect national safety practices, where empirical substantiation (for the IEC or national requirement) is not available or the text has not been in

42、cluded in the IEC standard. DC These are National Differences based on the component standards and will not be deleted until a particular component standard is harmonized with the IEC component standard. OCTOBER 31, 2014 CAN/CSA-C22.2 NO. 60745-2-2-04 UL 60745-2-2 6UL COPYRIGHTED MATERIAL NOT AUTHOR

43、IZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL DE These are National Differences based on editorial comments or corrections. JANUARY 23, 2009 CAN/CSA-C22.2 NO. 60745-2-2-04 UL 60745-2-2 7UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT

44、 PERMISSION FROM UL INTERNATIONAL ELECTROTECHNICAL COMMISSION HAND-HELD MOTOR-OPERATED ELECTRIC TOOLS SAFETY PART 2-2: PARTICULAR REQUIREMENTS FOR SCREWDRIVERS AND IMPACT WRENCHES FOREWORD 1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprisi

45、ng all national electrotechnical committees (IEC National Committees). The object of IEC is to promote international co-operation on all questions concerning standardization in the electrical and electronic elds. To this end and in addition to other activities, IEC publishes International Standards,

46、 Technical Specications, Technical Reports, Publicly Available Specications (PAS) and Guides (hereafter referred to as “IEC Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with may participate in this preparatory wo

47、rk. International, governmental and nongovernmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely with the International Organization for Standardization (ISO) in accordance with conditions determined by agreement between the two organizations. 2)

48、 The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international consensus of opinion on the relevant subjects since each technical committee has representation from all interested IEC National Committees. 3) IEC Publications have the form of recommend

49、ations for international use and are accepted by IEC National Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any misinterpretation by any end user. 4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications transparently to the maximum extent possibl