ANSI UL 61010-2-061-2015 UL Standard for Safety Requirements for Electrical Equipment for Measurement Control and Laboratory Use C Part 2-061 Particular Requirements for Laboratory.pdf

1、UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL UL 61010-2-061 (IEC 61010-2-061:2015) Safety Requirements for Electrical Equipment for Measurement, Control and Laboratory Use Part 2-061: Particular Requirements for Laboratory Atomic Spectrom

2、eters with Thermal Atomization and IonizationUL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM ULUL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL UL Standard for Safety for Safety Requirem

3、ents for Electrical Equipment for Measurement, Control and Laboratory Use Part 2-061: Particular Requirements for Laboratory Atomic Spectrometers with Thermal Atomization and Ionization, UL 61010-2-061 (IEC 61010-2-061:2015) Third Edition, Dated July 31, 2015 Summary of Topics Adoption of IEC 61010-

4、2-061, Safety Requirements for Electrical Equipment for Measurement, Control and Laboratory Use Part 2-061: Particular Requirements for Laboratory Atomic Spectrometers with Thermal Atomization and Ionization (third edition issued March 2015) as a new IEC-based UL standard, UL 61010-2-061 (IEC 61010-

5、2-061:2015), with no National Differences. Although this is the rst-time publication of this Standard by UL, it is being published as the Third edition in order to align ULs edition number with that of the IEC Standard. As a result, one or more UL edition numbers have been skipped to match that of t

6、he IEC edition number. The new requirements are substantially in accordance with Proposal(s) on this subject dated June 5, 2015. All rights reserved. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form by any means, electronic, mechanical photocopy

7、ing, recording, or otherwise without prior permission of UL. UL provides this Standard as is without warranty of any kind, either expressed or implied, including but not limited to, the implied warranties of merchantability or tness for any purpose. In no event will UL be liable for any special, inc

8、idental, consequential, indirect or similar damages, including loss of prots, lost savings, loss of data, or any other damages arising out of the use of or the inability to use this Standard, even if UL or an authorized UL representative has been advised of the possibility of such damage. In no even

9、t shall ULs liability for any damage ever exceed the price paid for this Standard, regardless of the form of the claim. Users of the electronic versions of ULs Standards for Safety agree to defend, indemnify, and hold UL harmless from and against any loss, expense, liability, damage, claim, or judgm

10、ent (including reasonable attorneys fees) resulting from any error or deviation introduced while purchaser is storing an electronic Standard on the purchasers computer system. The requirements in this Standard are now in effect, except for those paragraphs, sections, tables, gures, and/or other elem

11、ents of the Standard having future effective dates as indicated in the preface. The prior text for requirements that have been revised and that have a future effective date are located after the Standard, and are preceded by a SUPERSEDED REQUIREMENTS notice. JULY 31, 2015 UL 61010-2-061 (IEC 61010-2

12、-061:2015) tr1UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL JULY 31, 2015 UL 61010-2-061 (IEC 61010-2-061:2015) tr2 No Text on This PageUL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM

13、 UL JULY 31, 2015 1 UL 61010-2-061 (IEC 61010-2-061:2015) Safety Requirements for Electrical Equipment for Measurement, Control and Laboratory Use Part 2-061: Particular Requirements for Laboratory Atomic Spectrometers with Thermal Atomization and Ionization Third Edition July 31, 2015 This ANSI/UL

14、Standard for Safety consists of the Third Edition dated July 31, 2015. The most recent designation of ANSI/UL 61010-2-061 (IEC 61010-2-061:2015) as an American National Standard (ANSI) occurred on July 31, 2015. ANSI approval for a standard does not include the Cover Page, Transmittal Pages, Title P

15、age, Preface, or effective date information. The IEC Foreword is also excluded from the ANSI approval of IEC-based standards. Comments or proposals for revisions on any part of the Standard may be submitted to UL at any time. Proposals should be submitted via a Proposal Request in ULs On-Line Collab

16、orative Standards Development System (CSDS) at http:/. ULs Standards for Safety are copyrighted by UL. Neither a printed nor electronic copy of a Standard should be altered in any way. All of ULs Standards and all copyrights, ownerships, and rights regarding those Standards shall remain the sole and

17、 exclusive property of UL. COPYRIGHT 2015 UNDERWRITERS LABORATORIES INC. ANSI/UL 61010-2-061-2015UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL JULY 31, 2015 UL 61010-2-061 (IEC 61010-2-061:2015) 2 No Text on This PageUL COPYRIGHTED MATERIA

18、L NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL CONTENTS Preface (UL) 4 FOREWORD 5 1 Scope and object .8 1.1 Scope .8 2 Normative references 8 3 Terms and denitions 8 4 Tests 9 5 Marking and documentation 9 5.2 Warning markings .10 6 Protection against electric s

19、hock .13 7 Protection against mechanical HAZARDS 14 8 Resistance to mechanical stresses .14 8.1 General 14 9 Protection against the spread of re 14 10 Equipment temperature limits and resistance to heat 14 10.1 Surface temperature limits for protection against burns .14 11 Protection against HAZARDS

20、 from uids 14 11.1 General .14 12 Protection against radiation, including laser sources, and against sonic and ultrasonic pressure .16 13 Protection against liberated gases and substances, explosion and implosion .16 13.1 Poisonous and injurious gases and substances 16 14 Components and subassemblie

21、s .18 15 Protection by interlocks 18 16 HAZARDS resulting from application .18 17 RISK Assessment 19 Annexes Annex F (normative) Routine tests F.101 Gas leakage test 21 Annex H (informative) Index of dened terms Bibliography JULY 31, 2015 UL 61010-2-061 (IEC 61010-2-061:2015) 3UL COPYRIGHTED MATERIA

22、L NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL Preface (UL) This UL Standard is based on IEC Publication 61010-2-061: third edition, Safety Requirements for Electrical Equipment for Measurement, Control and Laboratory Use Part 2-061: Particular Requirements for

23、Laboratory Atomic Spectrometers with Thermal Atomization and Ionization. IEC publication 61010-2-061 is copyrighted by the IEC. Efforts have been made to synchronize the UL edition number with that of the corresponding IEC standard with which this standard is harmonized. As a result, one or more UL

24、edition numbers have been skipped to match that of the IEC edition number. This UL Standard 61010-2-061 Standard for Safety for Safety Requirements for Electrical Equipment for Measurement, Control and Laboratory Use Part 2-061: Particular Requirements for Laboratory Atomic Spectrometers with Therma

25、l Atomization and Ionization, is to be used in conjunction with the third edition of UL 61010-1. The requirements for laboratory equipment for the heating of materials are contained in this Part 2 Standard and UL 61010-2-061. Requirements of this Part 2 Standard, where stated, amend the requirements

26、 of UL 61010-1. Where a particular subclause of UL 61010-1 is not mentioned in UL 61010-2-061, the UL 61010-1 subclause applies. The text, gures and tables of IEC Publication Safety Requirements for Electrical Equipment for Measurement, Control and Laboratory Use Part 2-061: Particular Requirements

27、for Laboratory Atomic Spectrometers with Thermal Atomization and Ionization, IEC 61010-2-061, copyright March, 2015 are used in this Standard with the consent of the IEC and the American National Standards Institute (ANSI). The IEC copyrighted material has been reproduced with permission from ANSI.

28、ANSI should be contacted regarding the reproduction of any portion of the IEC material. The IEC Foreword and Introduction are not a part of the requirements of this Standard but are included for information purposes only. Copies of IEC Publication 61010-2-061 may be purchased from ANSI, 11 West 42nd

29、 Street, New York, New York, 10036, (212) 642-4900. Note Although the intended primary application of this Standard is stated in its Scope, it is important to note that it remains the responsibility of the users of the Standard to judge its suitability for their particular purpose. UL Effective Date

30、 The effective date for UL 61010-2-061 (IEC 61010-2-061:2015), Third edition is July 31, 2015. A UL effective date is one established by Underwriters Laboratories Inc. and is not part of the ANSI approved standard. JULY 31, 2015 UL 61010-2-061 (IEC 61010-2-061:2015) 4UL COPYRIGHTED MATERIAL NOT AUTH

31、ORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL INTERNATIONAL ELECTROTECHNICAL COMMISSION SAFETY REQUIREMENTS FOR ELECTRICAL EQUIPMENT FOR MEASUREMENT, CONTROL AND LABORATORY USE Part 2-061: Particular requirements for laboratory atomic spectrometers with thermal atomizati

32、on and ionization FOREWORD 1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising all national electrotechnical committees (IEC National Committees). The object of IEC is to promote international co-operation on all questions concerning stan

33、dardization in the electrical and electronic elds. To this end and in addition to other activities, IEC publishes International Standards, Technical Specications, Technical Reports, Publicly Available Specications (PAS) and Guides (hereafter referred to as “IEC Publication(s)”). Their preparation is

34、 entrusted to technical committees; any IEC National Committee interested in the subject dealt with may participate in this preparatory work. International, governmental and nongovernmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely with the In

35、ternational Organization for Standardization (ISO) in accordance with conditions determined by agreement between the two organizations. 2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international consensus of opinion on the relevant subjects sin

36、ce each technical committee has representation from all interested IEC National Committees. 3) IEC Publications have the form of recommendations for international use and are accepted by IEC National Committees in that sense. While all reasonable efforts are made to ensure that the technical content

37、 of IEC Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any misinterpretation by any end user. 4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications transparently to the maximum extent possible

38、in their national and regional publications. Any divergence between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in the latter. 5) IEC itself does not provide any attestation of conformity. Independent certication bodies provide conformity ass

39、essment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any services carried out by independent certication bodies. 6) All users should ensure that they have the latest edition of this publication. 7) No liability shall attach to IEC or its directors, emplo

40、yees, servants or agents including individual experts and members of its technical committees and IEC National Committees for any personal injury, property damage or other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and expenses arising out of the

41、 publication, use of, or reliance upon, this IEC Publication or any other IEC Publications. 8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is indispensable for the correct application of this publication. 9) Attention is drawn to the p

42、ossibility that some of the elements of this IEC Publication may be the subject of patent rights. IEC shall not be held responsible for identifying any or all such patent rights. International Standard IEC 61010-2-061 has been prepared by IEC technical committee 66: Safety of measuring, control and

43、laboratory equipment. It has the status of a group safety publication in accordance with IEC Guide 104. JULY 31, 2015 UL 61010-2-061 (IEC 61010-2-061:2015) 5UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL This third edition cancels and repla

44、ces the second edition published in 2003. It constitutes a technical revision and includes the following signicant changes from the second edition, as well as numerous other changes: exclusion of equipment, whose size and weight make unintentional movement unlikely, from the drop test in Clause 8. n

45、otes have been re-phrased according to ISO/IEC Directives. The text of this standard is based on the following documents: FDIS Report on voting 66/553/FDIS 66/568/RVD Full information on the voting for the approval of this standard can be found in the report on voting indicated in the above table. T

46、his publication has been drafted in accordance with the ISO/IEC Directives, Part 2. A list of all parts of the IEC 61010 series, under the general title: Safety requirements for electrical equipment for measurement, control, and laboratory use, may be found on the IEC website. This Part 2-061 is int

47、ended to be used in conjunction with IEC 61010-1. It was established on the basis of the third edition (2010). This Part 2-061 supplements or modies the corresponding clauses in IEC 61010-1 so as to convert that publication into the IEC standard Safety requirements for laboratory atomic spectrometer

48、s with thermal atomization and ionization. Where a particular subclause of Part 1 is not mentioned in this Part 2, that subclause applies as far as is reasonable. Where this part states “addition”, “modication”, “replacement”, or “deletion” the relevant requirement, test specication or note in Part

49、1 should be adapted accordingly. In this standard: 1) the following print types are used: requirements: in roman type; NOTES: in small roman type; conformity and test: in italic type; terms used throughout this standard which have been dened in Clause 3: SMALL ROMAN CAPITALS; 2) subclauses, gures, tables and notes which are additional to those in Part 1 are numbered starting from 101. Additional annexes are lettered starting from AA. The committee has decided that the contents of this publicat