ANSI UL 61010-2-201-2014 UL Standard for Safety Requirements for Electrical Equipment for Measurement Control and Laboratory Use - Part 2-201 Particular Requirements for Control Eq.pdf

1、UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL UL 61010-2-201 Safety Requirements for Electrical Equipment for Measurement, Control, and Laboratory Use Part 2-201: Particular Requirements for Control Equipment STANDARD FOR SAFETYUL COPYRIGH

2、TED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM ULUL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL UL Standard for Safety Requirements for Electrical Equipment for Measurement, Control, and Laborat

3、ory Use Part 2-201: Particular Requirements for Control Equipment, UL 61010-2-201 First Edition, Dated January 24, 2014 Summary of Topics This revision of UL 61010-2-201 was issued to include the following changes: 1. Addition of Requirements for the Durability of Markings for Open Equipment as Clau

4、se 5.3 as a National Difference. Text that has been changed in any manner or impacted by ULs electronic publishing system is marked with a vertical line in the margin. The new requirements are substantially in accordance with Proposal(s) on this subject dated December 30, 2016. All rights reserved.

5、No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form by any means, electronic, mechanical photocopying, recording, or otherwise without prior permission of UL. UL provides this Standard as is without warranty of any kind, either expressed or implied

6、, including but not limited to, the implied warranties of merchantability or tness for any purpose. In no event will UL be liable for any special, incidental, consequential, indirect or similar damages, including loss of prots, lost savings, loss of data, or any other damages arising out of the use

7、of or the inability to use this Standard, even if UL or an authorized UL representative has been advised of the possibility of such damage. In no event shall ULs liability for any damage ever exceed the price paid for this Standard, regardless of the form of the claim. Users of the electronic versio

8、ns of ULs Standards for Safety agree to defend, indemnify, and hold UL harmless from and against any loss, expense, liability, damage, claim, or judgment (including reasonable attorneys fees) resulting from any error or deviation introduced while purchaser is storing an electronic Standard on the pu

9、rchasers computer system. FEBRUARY 20, 2017 UL 61010-2-201 tr1UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL FEBRUARY 20, 2017 UL 61010-2-201 tr2 No Text on This PageUL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIB

10、UTION WITHOUT PERMISSION FROM UL JANUARY 24, 2014 (Title Page Reprinted: February 20, 2017) 1 UL 61010-2-201 Standard for Safety Requirements for Electrical Equipment for Measurement, Control, and Laboratory Use Part 2-201: Particular Requirements for Control Equipment First Edition January 24, 2014

11、 This ANSI/UL Standard for Safety consists of the First Edition including revisions through February 20, 2017. The most recent designation of ANSI/UL 61010-2-201 as an American National Standard (ANSI) occurred on February 20, 2017. ANSI approval for a standard does not include the Cover Page, Trans

12、mittal Pages, Title Page, or Preface. The National Difference Page and IEC Foreword are also excluded from the ANSI approval of IEC-based standards. Comments or proposals for revisions on any part of the Standard may be submitted to UL at any time. Proposals should be submitted via a Proposal Reques

13、t in ULs On-Line Collaborative Standards Development System (CSDS) at https:/. ULs Standards for Safety are copyrighted by UL. Neither a printed nor electronic copy of a Standard should be altered in any way. All of ULs Standards and all copyrights, ownerships, and rights regarding those Standards s

14、hall remain the sole and exclusive property of UL. COPYRIGHT 2017 UNDERWRITERS LABORATORIES INC. ANSI/UL 61010-2-201-2017UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL FEBRUARY 20, 2017 UL 61010-2-201 2 No Text on This PageUL COPYRIGHTED MA

15、TERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL CONTENTS PREFACE 6 NATIONAL DIFFERENCES . 6 FOREWORD 7 INTRODUCTION . 9 1 Scope and object 10 2 Normative references .12 3 Terms and denitions 13 4 Tests .14 4.1 General 14 4.4 Testing in single fault condition

16、 15 5 Marking and documentation .16 6 Protection against electric shock .16 6.10 Connection to the mains supply source and connections between parts of equipment .32 6.11 Disconnection from supply source 32 7 Protection against mechanical hazards .32 7.2 Sharp edges 33 7.7 Expelled parts 34 8 Resist

17、ance to mechanical stresses .34 8.3 Drop test .35 9 Protection against the spread of re 35 9.2 Eliminating or reducing the sources of ignition within the equipment .35 10 Equipment temperature limits and resistance to heat 36 10.1 Surface temperature limits for protection against burns .36 10.3 Othe

18、r temperature measurements 37 11 Protection against hazards from uids .39 11.6 Specially protected equipment .39 12 Protection against radiation, including laser sources, and against sonic and ultrasonic pressure .39 13 Protection against liberated gases and substances, explosion and implosion .40 1

19、3.1 Poisonous and injurious gases and substances 40 14 Components and subassemblies .40 14.101 Components bridging insulation 40 14.102 Switching devices 41 15 Protection by interlocks 41 16 Hazards resulting from application 41 17 Risk assessment .42 Annexes Annex F (normative) Routine tests F.2 Pr

20、otective earth 44 F.3.1 General 44 F.4 Floating circuits 44 FEBRUARY 20, 2017 UL 61010-2-201 3UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL F.101 Supply circuits other than mains and oating circuits .44 Annex L (informative) Index of dened

21、 terms Annex AA (informative) General approach to safety for control equipment AA.1 Personnel 47 AA.1.1 General .47 AA.1.2 Operator 47 AA.1.3 Service personnel 48 AA.2 Operating access areas .48 AA.3 Service access areas .48 AA.4 Equipment types 48 AA.4.1 General .48 AA.4.2 Open equipment .48 AA.4.3

22、 Enclosed equipment 49 Annex BB (informative) System drawing of isolation boundaries BB.1 General .50 BB.2 Installation environment of open control equipment .50 BB.3 Control equipment electrical safety drawing 52 BB.4 Applying the standard to the control equipment electrical safety drawing 54 BB.5

23、Example methodologies for electrical safety and documentation 55 BB.6 Conclusion .58 Annex CC (informative) Historical techniques for secondary circuits CC.1 Secondary circuits background .59 CC.2 Secondary circuits without risk of electrical shock 59 CC.2.1 General .59 CC.2.2 Secondary circuits whi

24、ch do not pose a risk of electrical shock 60 CC.3 Secondary circuits without risk of spread of re 61 CC.3.1 General .61 CC.3.2 Secondary circuits which do not pose a risk of spread of re 62 Annex DD (informative) Cross references between IEC 61010-2-201 and IEC 61010-1:2010 or IEC 61131-2:2007 Bibli

25、ography FEBRUARY 20, 2017 UL 61010-2-201 4UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL FEBRUARY 20, 2017 UL 61010-2-201 5 No Text on This PageUL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSI

26、ON FROM UL PREFACE This UL Standard is based on IEC Publication 61010-2-201: rst edition, Safety Requirements for Electrical Equipment for Measurement, Control, and Laboratory Use Part 2-201: Particular Requirements for Control Equipment. IEC publication 61010-2-201 is copyrighted by the IEC. This U

27、L Standard 61010-2-201 Standard for Safety Requirements for Electrical Equipment for Measurement, Control, and Laboratory use Part 2-201: Particular Requirements for Control Equipment, is to be used in conjunction with the third edition of UL 61010-1. The requirements for control equipment are conta

28、ined in this Part 2 Standard and UL 61010-1. Requirements of this Part 2 Standard, where stated, amend the requirements of UL 61010-1. Where a particular subclause of UL 61010-1 is not mentioned in UL 61010-2-201, the UL 61010-1 subclause applies. These materials are subject to copyright claims of I

29、EC and UL. No part of this publication may be reproduced in any form, including an electronic retrieval system, without the prior written permission of UL. All requests pertaining to the UL 61010-2-201 Standard for Safety Requirements for Electrical Equipment for Measurement, Control, and Laboratory

30、 use Part 2-201: Particular Requirements for Control Equipment Standard should be submitted to UL. Note Although the intended primary application of this Standard is stated in its Scope, it is important to note that it remains the responsibility of the users of the Standard to judge its suitability

31、for their particular purpose. FEBRUARY 20, 2017 UL 61010-2-201 6UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL NATIONAL DIFFERENCES National Differences from the text of International Electrotechnical Commission (IEC) Publication 61010-2-20

32、1, Safety requirements for electrical equipment for measurement, control, and laboratory use Part 2-201: Particular requirements for control equipment copyright 2013 are indicated by notations (differences) and are presented in bold text. There are ve types of National Differences as noted below. Th

33、e difference type is noted on the first line of the National Difference in the standard. The standard may not include all types of these National Differences. DR These are National Differences based on the national regulatory requirements. D1 These are National Differences which are based on basic s

34、afety principles and requirements, elimination of which would compromise safety for consumers and users of products. D2 These are national differences from IEC requirements based on existing safety practices. These requirements reect national safety practices, where empirical substantiation (for the

35、 IEC or national requirement) is not available or the text has not been included in the IEC standard. DC These are National Differences based on the component standards and will not be deleted until a particular component standard is harmonized with the IEC component standard. DE These are National

36、Differences based on editorial comments or corrections. Each national difference contains a description of what the national difference entails. Typically one of the following words is used to explain how the text of the national difference is to be applied to the base IEC text: Addition / Add - An

37、addition entails adding a complete new numbered clause, subclause, table, gure, or annex. Addition is not meant to include adding select words to the base IEC text. Modication / Modify - A modication is an altering of the existing base IEC text such as the addition, replacement or deletion of certai

38、n words or the replacement of an entire clause, subclause, table, gure, or annex of the base IEC text. Deletion / Delete - A deletion entails complete deletion of an entire numbered clause, subclause, table, gure, or annex without any replacement text. FEBRUARY 20, 2017 UL 61010-2-201 6AUL COPYRIGHT

39、ED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL FEBRUARY 20, 2017 UL 61010-2-201 6B No Text on This PageUL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL INTERNATIONAL ELECTROTECHNICAL COMMISSION

40、SAFETY REQUIREMENTS FOR ELECTRICAL EQUIPMENT FOR MEASUREMENT, CONTROL, AND LABORATORY USE Part 2-201: Particular requirements for control equipment FOREWORD 1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising all national electrotechnical

41、 committees (IEC National Committees). The object of IEC is to promote international co-operation on all questions concerning standardization in the electrical and electronic elds. To this end and in addition to other activities, IEC publishes International Standards, Technical Specications, Technic

42、al Reports, Publicly Available Specications (PAS) and Guides (hereafter referred to as “IEC Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with may participate in this preparatory work. International, governmental

43、and nongovernmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely with the International Organization for Standardization (ISO) in accordance with conditions determined by agreement between the two organizations. 2) The formal decisions or agreeme

44、nts of IEC on technical matters express, as nearly as possible, an international consensus of opinion on the relevant subjects since each technical committee has representation from all interested IEC National Committees. 3) IEC Publications have the form of recommendations for international use and

45、 are accepted by IEC National Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any misinterpretation by any end user. 4) In order to promote i

46、nternational uniformity, IEC National Committees undertake to apply IEC Publications transparently to the maximum extent possible in their national and regional publications. Any divergence between any IEC Publication and the corresponding national or regional publication shall be clearly indicated

47、in the latter. 5) IEC itself does not provide any attestation of conformity. Independent certication bodies provide conformity assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any services carried out by independent certication bodies. 6) All user

48、s should ensure that they have the latest edition of this publication. 7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and members of its technical committees and IEC National Committees for any personal injury, property damage or othe

49、r damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC Publications. 8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is indispensable for the correct application of this publication. 9) Attention is drawn to the possibility that some of the elements of this IEC Publication may b