ANSI UL 62841-3-9-2016 UL Standard for Safety Electric Motor-Operated Hand-Held Tools Transportable Tools And Lawn And Garden Machinery C Safety C Part 3-9 Particular Requirements .pdf

1、UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL UL 62841-3-9 Electric Motor-Operated Hand-Held Tools, Transportable Tools And Lawn And Garden Machinery Safety Part 3-9: Particular Requirements For Transportable Mitre Saws STANDARD FOR SAFETY

2、UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM ULUL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL UL Standard for Safety for Electric Motor-Operated Hand-Held Tools, Transportable Tools

3、 And Lawn And Garden Machinery Safety Part 3-9: Particular Requirements For Transportable Mitre SawsUL 62841-3-9 First Edition, Dated January 13, 2016 Summary of Topics The revision pages dated April 28, 2017 are being issued to incorporate the following and to reect the latest ANSI approval date. 1

4、. Addition Of Clause 1DV To Modify The Scope Of The Standard By Specifying A 400 mm Saw Blade Diameter 2. Revision To Table 4, Required Performance Levels, And Deletion Of Table 4DV To Align With Changes In IEC Corrigendum 1 Of IEC 62841-3-9 3. Revision To The Marking Requirements in Clause 8.3 To A

5、lign With Changes In IEC Corrigendum 2 Of IEC 62841-3-9 Please note that the national difference document incorporates all of the U.S. national differences for UL 60745-3-9 including the changes to national differences itemized above. This standard is an adoption of IEC UL 62841-3-9, Edition 1 publi

6、shed by the IEC August 2014. The new requirements are substantially in accordance with Proposal(s) on this subject dated January 27, 2017. All rights reserved. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form by any means, electronic, mechanical

7、 photocopying, recording, or otherwise without prior permission of UL. UL provides this Standard as is without warranty of any kind, either expressed or implied, including but not limited to, the implied warranties of merchantability or tness for any purpose. In no event will UL be liable for any sp

8、ecial, incidental, consequential, indirect or similar damages, including loss of prots, lost savings, loss of data, or any other damages arising out of the use of or the inability to use this Standard, even if UL or an authorized UL representative has been advised of the possibility of such damage.

9、In no event shall ULs liability for any damage ever exceed the price paid for this Standard, regardless of the form of the claim. Users of the electronic versions of ULs Standards for Safety agree to defend, indemnify, and hold UL harmless from and against any loss, expense, liability, damage, claim

10、, or judgment (including reasonable attorneys fees) resulting from any error or deviation introduced while purchaser is storing an electronic Standard on the purchasers computer system. APRIL 28, 2017 UL 62841-3-9 tr1UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WIT

11、HOUT PERMISSION FROM UL APRIL 28, 2017 UL 62841-3-9 tr2 No Text on This PageUL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL CSA Group CAN/CSA-C22.2 No. 62841-3-9:16 First Edition (IEC 62841-3-9:2014, MOD) Underwriters Laboratories Inc. UL 62

12、841-3-9 First Edition Electric Motor-Operated Hand-Held Tools, Transportable Tools And Lawn And Garden Machinery Safety Part 3-9: Particular Requirements For Transportable Mitre Saws January 13, 2016 (Title Page Reprinted: April 28, 2017) This national standard is based on publication IEC 62841-3-9,

13、 First Edition (2014). ANSI/UL 62841-3-9-2017 Approved byUL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL Commitment for Amendments This standard is issued jointly by the Canadian Standards Association (operating as “CSA Group”), and Underwri

14、ters Laboratories Inc. (UL). Comments or proposals for revisions on any part of the standard may be submitted to CSA Group, or UL at anytime. Revisions to this standard will be made only after processing according to the standards development procedures of CSA Group and UL. CSA Group and UL will iss

15、ue revisions to this standard by means of a new edition or revised or additional pages bearing their date of issue. ISBN 978-1-4883-0036-3 2016 CSA Group All rights reserved. No part of this publication may be reproduced in any form whatsoever without the prior permission of the publisher. This Stan

16、dard is subject to review ve years from the date of publication, and suggestions for its improvement will be referred to the appropriate committee. To submit a proposal for change, please send the following information to inquirescsagroup.org and include Proposal for change in the subject line: Stan

17、dard designation (number); relevant clause, table, and/or gure number; wording of the proposed change; and rationale for the change. To purchase CSA Group Standards and related publications, visit CSA Groups Online Store at shop.csa.ca or call toll-free 1-800-463-6727 or 416-747-4044. Copyright 2017

18、 Underwriters Laboratories Inc. ULs Standards for Safety are copyrighted by UL. Neither a printed nor electronic copy of a Standard should be altered in any way. All of ULs Standards and all copyrights, ownerships, and rights regarding those Standards shall remain the sole and exclusive property of

19、UL. This ANSI/UL Standard for Safety consists of the First Edition including revisions through April 28, 2017. The most recent designation of ANSI/UL 62841-3-9 as an American National Standard (ANSI) occurred on April 28, 2017. ANSI approval for a standard does not include the Cover Page, Transmitta

20、l Pages, Title Page (front and back), or the Preface. The National Difference Page and IEC Foreword are also excluded from the ANSI approval of IEC-based standards. Comments or proposals for revisions on any part of the Standard may be submitted to UL at any time. Proposals should be submitted via a

21、 Proposal Request in ULs On-Line Collaborative Standards Development System (CSDS) at https:/. To purchase UL Standards, visit Comm 2000 at http:/m- or call toll-free 1-888-853-3503.UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL CONTENTS Pr

22、eface . 5 NATIONAL DIFFERENCES . 7 FOREWORD 8 1 Scope .10A 2 Normative references .10A 3 Terms and denitions .10B 4 General requirements 13 5 General conditions for the tests 13 6 Radiation, toxicity and similar hazards 14 7 Classication 14 8 Marking and instructions 14 9 Protection against access t

23、o live parts 18 10 Starting 18 11 Input and current .18 12 Heating 19 13 Resistance to heat and re 19 14 Moisture resistance .19 15 Resistance to rusting 19 16 Overload protection of transformers and associated circuits 19 17 Endurance .19 18 Abnormal operation .19 19 Mechanical hazards .20 19.101 S

24、aw blade guards 20 20 Mechanical strength .25 21 Construction .26 21.101 Construction to facilitate cutting tool installations .28 21.102 Table top .28 21.103 Table fence .29 21.104 Mitre saws 31 21.105 Spindle and anges 31 22 Internal wiring 32 23 Components .32 24 Supply connection and external ex

25、ible cables and cords 32 25 Terminals for external conductors .32 26 Provision for earthing 32 27 Screws and connections .32 28 Creepage distances, clearances and distances through insulation 32 Annexes Annex I (informative) Measurement of noise and vibration emissions I.2 Noise test code (grade 2)

26、44 I.2.4 Installation and mounting conditions of the power tools during noise tests .44 I.2.5 Operating conditions 44 APRIL 28, 2017 CAN/CSA-C22.2 NO. 62841-3-9:16 UL 62841-3-9 3UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL I.3 Vibration .

27、44 Annex K (normative) Battery tools and battery packs Annex L (normative) Battery tools and battery packs provided with mains connection or non-isolated sources Bibliography JANUARY 13, 2016 CAN/CSA-C22.2 NO. 62841-3-9:16 UL 62841-3-9 4UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION

28、 OR DISTRIBUTION WITHOUT PERMISSION FROM UL Preface This is the harmonized CSA Group and UL Standard for Motor-Operated Hand-Held Tools, Transportable Tools And Lawn And Garden Machinery Safety Part 3-9: Particular Requirements For Transportable Mitre Saws. It is the First edition of CAN/CSA-C22.2 N

29、o. 62841-3-9 and the First edition of UL 62841-3-9. This harmonized Standard has been jointly revised on April 28, 2017. For this purpose, CSA Group and UL are issuing revision pages dated April 28, 2017. This harmonized standard is based on IEC Publication 62841-3-9: edition 1, Motor-Operated Hand-

30、Held Tools, Transportable Tools And Lawn And Garden Machinery Safety Part 3-9: Particular Requirements For Transportable Mitre Saws issued 8-2014. IEC publication 62841-3-9 is copyrighted by the IEC. This harmonized standard was prepared by CSA Group and Underwriters Laboratories Inc. (UL). The effo

31、rts and support of the International Harmonization Committee adoption of the IEC series of standards for Hand-Held, Motor-Operated, and Transportable Tools and Lawn and Garden Machinery are gratefully acknowledged. This standard is considered suitable for use for conformity assessment within the sta

32、ted scope of the standard. This standard was reviewed by the CSA Subcommittee on Safety of Hand-Held Motor-Operated Electric Tools, under the jurisdiction of the CSA Technical Committee on Consumer and Commercial Products and the CSA Strategic Steering Committee on Requirements for Electrical Safety

33、, and has been formally approved by the CSA Technical Committee. This standard has been approved as a National Standard of Canada by the Standards Council of Canada (SCC). This standard has been approved by the American National Standards Institute (ANSI) as an American National Standard. Applicatio

34、n of Standard Where reference is made to a specic number of samples to be tested, the specied number is to be considered a minimum quantity. Note: Although the intended primary application of this standard is stated in its scope, it is important to note that it remains the responsibility of the user

35、s of the standard to judge its suitability for their particular purpose. This CAN/CSA-C22.2 No. 62841-3-9 Standard for Safety for Motor-Operated Hand-Held Tools, Transportable Tools And Lawn And Garden Machinery Safety Part 3-9: Particular Requirements For Transportable Mitre Saws is to be used in c

36、onjunction with the First edition of CAN/CSA-C22.2 No. 62841-1. The requirements for transportable mitre saws are contained in this Part 3 Standard and CAN/CSA-C22.2 No. 62841-1. Requirements of this Part 3 Standard, where stated, amend the requirements of CAN/CSA-C22.2 No. 62841-1. Where a particul

37、ar subclause of CAN/CSA-C22.2 No. 62841-1 is not mentioned in CAN/CSA-C22.2 No. 62841-3-9, the CAN/CSA-C22.2 No. 62841-1 subclause applies. This UL Standard 62841-3-9 Standard for Safety for Standard for Safety for Motor-Operated Hand-Held Tools, Transportable Tools And Lawn And Garden Machinery Saf

38、ety Part 3-9: Particular Requirements For Transportable Mitre Saws, is to be used in conjunction with the First edition of UL APRIL 28, 2017 CAN/CSA-C22.2 NO. 62841-3-9:16 UL 62841-3-9 5UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL 62841-1

39、. The requirements for transportable mitre saws are contained in this Part 3 Standard and UL 62841-1. Requirements of this Part 3 Standard, where stated, amend the requirements of UL 62841-1. Where a particular subclause of UL 62841-1 is not mentioned in UL 62841-3-9, the UL 62841-1 subclause applie

40、s. Level of Harmonization This standard adopts the IEC text with national differences. This standard is published as an equivalent standard for CSA Group and UL. An equivalent standard is a standard that is substantially the same in technical content, except as follows: Technical national difference

41、s are allowed for codes and governmental regulations as well as those recognized as being in accordance with NAFTA Article 905, for example, because of fundamental climatic, geographical, technological, or infrastructural factors, scientic justication, or the level of protection that the country con

42、siders appropriate. Presentation is word for word except for editorial changes. All national differences from the IEC text are included in the CSA Group and UL versions of the standard. While the technical content is the same in each organizations version, the format and presentation may differ. Rea

43、sons for Differences From IEC National differences from the IEC are being added in order to address safety and regulatory situations present in the US and Canada. Interpretations The interpretation by the standards development organization of an identical or equivalent standard is based on the liter

44、al text to determine compliance with the standard in accordance with the procedural rules of the standards development organization. If more than one interpretation of the literal text has been identied, a revision is to be proposed as soon as possible to each of the standards development organizati

45、ons to more accurately reect the intent. IEC Copyright For CSA Group, the text, gures, and tables of International Electrotechnical Commission Publication IEC 62841-3-9, Motor-Operated Hand-Held Tools, Transportable Tools And Lawn And Garden Machinery Safety Part 3-9: Particular Requirements For Tra

46、nsportable Mitre Saws, copyright 2014, are used in this standard with the consent of the International Electrotechnical Commission. The IEC Foreword is not a part of the requirements of this standard but is included for information purposes only. For UL, the text, gures and tables of IEC publication

47、 IEC 62841-3-9, Motor-Operated Hand-Held Tools, Transportable Tools And Lawn And Garden Machinery Safety Part 3-9: Particular Requirements For Transportable Mitre Saws, copyright 2014 are used in this standard with the consent of the IEC and the American National Standards Institute (ANSI). The IEC

48、copyrighted material has been reproduced with permission from ANSI. ANSI should be contacted regarding the reproduction of any portion of the IEC material. The IEC Foreword and Introduction are not a part of the requirements of this standard but are included for information purposes only. Copies of

49、IEC Publication IEC 62841-3-9 may be purchased from ANSI, 25 West 43rd Street, 4th Floor, New York, New York, 10036, (212) 642- 4900. APRIL 28, 2017 CAN/CSA-C22.2 NO. 62841-3-9:16 UL 62841-3-9 6UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL NATIONAL DIFFERENCES National Differences from the text of the International Electrotechnical Commission (IEC) publication 62841-3-9 (Motor-Operated