ANSI UL 810-1995 UL Standard for Safety Capacitors (Fifth Edition Reprint with Revisions Through and Including August 18 2014).pdf

1、UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL UL 810 CapacitorsUL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM ULUL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DIS

2、TRIBUTION WITHOUT PERMISSION FROM UL UL Standard for Safety for Capacitors, UL 810 Fifth Edition, Dated May 4, 1995 Summary of Topics These revisions to ANSI/UL 810 include the following changes in requirements: 1. Revision to Dielectric Voltage-Withstand Test. 2. Revision to Sample Preparation. Tex

3、t that has been changed in any manner or impacted by ULs electronic publishing system is marked with a vertical line in the margin. Changes in requirements are marked with a vertical line in the margin and are followed by an effective date note indicating the date of publication or the date on which

4、 the changed requirement becomes effective. The new and revised requirements are substantially in accordance with Proposal(s) on this subject dated June 13, 2014. All rights reserved. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form by any means

5、, electronic, mechanical photocopying, recording, or otherwise without prior permission of UL. UL provides this Standard as is without warranty of any kind, either expressed or implied, including but not limited to, the implied warranties of merchantability or tness for any purpose. In no event will

6、 UL be liable for any special, incidental, consequential, indirect or similar damages, including loss of prots, lost savings, loss of data, or any other damages arising out of the use of or the inability to use this Standard, even if UL or an authorized UL representative has been advised of the poss

7、ibility of such damage. In no event shall ULs liability for any damage ever exceed the price paid for this Standard, regardless of the form of the claim. Users of the electronic versions of ULs Standards for Safety agree to defend, indemnify, and hold UL harmless from and against any loss, expense,

8、liability, damage, claim, or judgment (including reasonable attorneys fees) resulting from any error or deviation introduced while purchaser is storing an electronic Standard on the purchasers computer system. The requirements in this Standard are now in effect, except for those paragraphs, sections

9、, tables, gures, and/or other elements of the Standard having future effective dates as indicated in the note following the affected item. The prior text for requirements that have been revised and that have a future effective date are located after the Standard, and are preceded by a SUPERSEDED REQ

10、UIREMENTS notice. AUGUST 18, 2014 UL 810 tr1UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL AUGUST 18, 2014 UL 810 tr2 No Text on This PageUL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FRO

11、M UL MAY 4, 1995 (Title Page Reprinted: August 18, 2014) 1 UL 810 Standard for Capacitors First Edition November, 1953 Second Edition May, 1973 Third Edition June, 1976 Fourth Edition September, 1981 Fifth Edition May 4, 1995 This ANSI/UL Standard for Safety consists of the Fifth Edition including r

12、evisions through August 18, 2014. The most recent designation of ANSI/UL 810 as an American National Standard (ANSI) occurred on August 18, 2014. ANSI approval for a standard does not include the Cover Page, Transmittal Pages, Title Page, or effective date information. Comments or proposals for revi

13、sions on any part of the Standard may be submitted to UL at any time. Proposals should be submitted via a Proposal Request in ULs On-Line Collaborative Standards Development System (CSDS) at http:/. ULs Standards for Safety are copyrighted by UL. Neither a printed nor electronic copy of a Standard s

14、hould be altered in any way. All of ULs Standards and all copyrights, ownerships, and rights regarding those Standards shall remain the sole and exclusive property of UL. COPYRIGHT 2014 UNDERWRITERS LABORATORIES INC. ANSI/UL 810-2014UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR

15、DISTRIBUTION WITHOUT PERMISSION FROM UL JULY 26, 2012 CAPACITORS - UL 810 2 No Text on This PageUL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL CONTENTS INTRODUCTION 1 Scope .5 2 Glossary .6 3 General 7 3.1 Components .7 3.2 Units of measure

16、ment .7 3.3 Undated references .7 PART I CAPACITORS CONSTRUCTION 4 Enclosure 8 4.1 General .8 4.2 Metallic 8 4.3 Nonmetallic 8 5 Internal Protection Bridge 9 6 Insulating Material .9 7 Leads, Terminals and Internal Wiring .11 8 Spacings 12A PERFORMANCE 9 Pull-Out Test .12B 9A Conductor Insulation Te

17、st 12B 9B Mold Stress Relief Test (Terminals Blocks/Terminal Connectors) .12C 10 Fault-Current Test .12C 10.1 General 12C 10.2 Sample preparation .14 10.3 Test method .15 10.3A Test method 15 10.4 Restrike test (expansion type protection only) 18 11 Dielectric Voltage-Withstand Test .18 11A Dielectr

18、ic Voltage-Withstand Test 18 MANUFACTURING AND PRODUCTION TESTS 12 Dielectric Voltage-Withstand Test 18A MARKINGS 13 General 18B JULY 26, 2012 CAPACITORS - UL 810 2AUL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL PART II POWER-FACTOR CORRECT

19、ION UNITS GENERAL 14 Terminology 18C CONSTRUCTION 15 Frame and Enclosure 18C 16 Accessibility of Uninsulated Live Parts, Moving Parts, and Film-Coated Wire .22 17 Protection Against Risks of Electric Shock and Injury to Persons .24 17.1 General .24 17.2 Live parts .24 17.3 Moving parts .24A 17.4 Mec

20、hanical servicing 25 17.5 Electrical servicing 25 18 Assembly 25 19 Protection Against Corrosion .26 20 Supply Connections .26 21 Wiring Terminals and Leads .28 21A Wire Bending Space .30 22 Current-Carrying Parts .30A 23 Internal Wiring 30B 23.1 General 30B 23.2 Protection of wiring .31 23.3 Electr

21、ical connections .31 24 Separation of Circuits .32 24.1 General .32 24.2 Separation barriers .32 24.3 Field wiring 33 25 Insulating Materials .33 26 Switches and Controls .34 27 Overload-Protective Devices .35 28 Fuses and Fuseholders 35 29 Printed Wiring 35 30 Spacings 36 30.1 General .36 30.2 Alte

22、rnative spacings 38 30.3 Insulating liners or barriers for the reduction of spacings 38 30.4 Spacings for controlled environment applications .39 31 Secondary Circuits 40 31A Secondary Circuits 40 31A.1 General 40 31A.2 Limited power sources .41 32 Grounding Connections 42A 33 Bonding of Internal Pa

23、rts .42C PERFORMANCE 34 General 44 35 Power Input Test .45 36 Draining of Charge Test .45 37 Open-Circuit Potential Test 45 JULY 26, 2012 CAPACITORS - UL 810 2BUL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL 37A Secondary Circuit Evaluations

24、 45 37A.1 SELV determination .45 37A.2 Limited power determination 46 38 Temperature Test .46 39 Dielectric Voltage-Withstand Test .47 40 Compression Test 47 41 Deection Test .48 42 Tightening Torque Test 48 43 Static Load Test 49 MANUFACTURING AND PRODUCTION TESTS 44 Dielectric Voltage-Withstand Te

25、st .49 RATINGS 45 Details .51 MARKINGS 46 General 51 47 Installation Instructions 53 OUTDOOR-USE UNITS 48 General 53 49 Construction .53 49.1 General .53 49.2 Corrosion protection 54 50 Rain Test 56 51 Gasket Tests .59 52 Metallic Coating Thickness Test 59 53 Markings .61 SUPPLEMENT SA - Electrolyti

26、c Capacitors SA1 Scope SA1 SA2 Glossary SA1 SA3 General SA1 SA4 Construction SA1 SA4.1 Enclosure SA1 SA4.2 Internal protection bridge .SA1 SA4.3 Insulating material .SA1 SA4.4 Electrolyte SA2 SA4.5 Leads and terminals .SA2 SA4.6 Spacings .SA2 SA5 Performance SA2 SA5.1 General SA2 SA5.2 Pull-out test

27、 SA3 SA5.3 Torque test (screw terminals) .SA3 SA5.4 Heating (sealing) test SA3 JULY 26, 2012 CAPACITORS - UL 810 2CUL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL SA5.5 Reverse polarity test .SA4 SA5.6 Pressure relief test SA4 SA5.7 Dielectr

28、ic voltage-withstand test .SA4 SA6 Markings .SA5 SA6.1 General SA5 SA6.2 Instructions .SA6 APPENDIX A Standards for ComponentsA1 JULY 26, 2012 CAPACITORS - UL 810 2DUL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL MARCH 3, 2008 CAPACITORS - U

29、L 810 3 No Text on This PageUL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL This page intentionally left blank. MARCH 3, 2008 CAPACITORS - UL 810 4UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMIS

30、SION FROM UL INTRODUCTION 1 Scope 1.1 The requirements in Part I of this Standard apply to enclosed capacitors with integral protection intended to reduce the risk of rupture and venting of the capacitor enclosure under internal fault conditions. These requirements apply to capacitors with expansion

31、 type protection rated 5 kilovolts or less, and capacitors with segmented lm type protection rated 2 kilovolts or less that are intended for use with appliances, lighting equipment, air conditioning and refrigeration equipment, motors, and the like, that comply with the requirements for such applian

32、ces and equipment. 1.1 revised July 26, 2012 1.1.1 The requirements of Part I may also be used to evaluate the construction only of these types of capacitors with ratings greater than the values noted in 1.1 but no greater than 7.2 kilovolts. Capacitors employing polymeric enclosures or capacitors e

33、mploying a partial metallic enclosure (i.e. remainder of enclosure such as the cap/cover which is not crimped to the case) that are not provided with internal protection and intended to be located in circuits not requiring fault current protection may be evaluated using only the construction require

34、ments of Part I. 1.1.1 revised July 26, 2012 1.2 The requirements in Part II of this standard apply to general-use power-factor-correction units consisting of one or more capacitors with or without protective fusing or overloads, with or without a switch or other disconnect device all within a prote

35、ctive enclosure; rated 600 volts maximum and intended for power-factor correction of circuits in accordance with the National Electrical Code, ANSI/NFPA 70. This equipment is intended for installation in ordinary locations, in accordance with the National Electrical Code, ANSI/NFPA 70, where the amb

36、ient temperature does not exceed 40C (104F) maximum. Exception: The requirements of Part II of this standard do not apply to power factor correction units containing automatic or other circuit monitoring/conditioning controls or automatic systems of multiple connected power factor correction units.

37、Power factor correction units with these additional features shall be evaluated to the Standard for Industrial Control Panels, UL 508A as an industrial control panel. Revised 1.2 effective May 21, 2012 1.2.1 A component capacitor used in a power factor correction unit as described in Part II of this

38、 Standard has been evaluated for across-the-line applications in accordance with Part I of this Standard and has been evaluated for a minimum fault current rating of 10K AFC. 1.2.1 revised March 3, 2008 1.2.2 The requirements of Supplement SA apply to electrolytic capacitors for motor start or simil

39、ar applications including dc circuits rated 600 V or less. 1.2.2 added March 3, 2008 1.3 A capacitor that complies with the requirements in Part I of this standard is intended to be mounted within an appliance or within equipment for which an acceptable outer enclosure is provided. 1.4 The requireme

40、nts in Part I and Part II do not apply to capacitors covered by the Standard for Across-the-Line, Antenna Coupling, and Line-by-Pass Capacitors for Radio- and Television-Type Appliances, UL 1414. JULY 26, 2012 CAPACITORS - UL 810 5UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DI

41、STRIBUTION WITHOUT PERMISSION FROM UL 1.5 Other types of capacitors may be investigated to establish compliance with these requirements, and with such additional test criteria as may be found necessary. 1.6 A product that contains features, characteristics, components, materials, or systems new or d

42、ifferent from those covered by the requirements in this standard, and that involves a risk of re or of electric shock or injury to persons shall be evaluated using appropriate additional component and end-product requirements to maintain the level of safety as originally anticipated by the intent of

43、 this standard. A product whose features, characteristics, components, materials, or systems conict with specic requirements or provisions of this standard does not comply with this standard. Revision of requirements shall be proposed and adopted in conformance with the methods employed for developm

44、ent, revision, and implementation of this standard. 1.6 revised March 3, 2008 2 Glossary 2.1 For the purpose of this standard the following denitions apply. 2.2 CAPACITOR ROLL The layered and rolled interior windings of a capacitor, which is also known as the element. 2.2.0 CLASS 2 CIRCUIT A circuit

45、 supplied by a Class 2 source in accordance with Article 725 of the National Electrical Code (NEC). 2.2.0 added March 3, 2008 2.2.1 COMPONENT CAPACITOR Refers to a capacitor evaluated to Part I of the Standard. A component capacitor is also referred to as capacitor. 2.2.1 added August 24, 1998 2.3 C

46、ONTROLLED ENVIRONMENT An environment that is relatively free of conductive contaminants, such as carbon dust and the like, that may result from the end-use equipment in which a capacitor or power-factor correction unit is installed or due to the location of the end-use equipment, and that is provide

47、d with protection against humidity and the formation of condensation. 2.3.1 DRY TYPE CAPACITOR A capacitor that contains no liquid and utilizes a solid dielectric medium other than wax. 2.3.1 added March 3, 2008 2.3.2 ELECTRODE, FOIL TYPE Capacitor plates consisting of thin metal or “foil” separated

48、 by a dielectric. 2.3.2 added March 3, 2008 2.3.3 ELECTRODE, METALLIZED Capacitor plates consisting of dielectric material covered with metallic deposits such as aluminum on the surface. This type of electrode has a tendency to self restore or re-heal after local breakdown of the dielectric. 2.3.3 a

49、dded March 3, 2008 2.3.4 ELECTROLYTE Current conducting solution (liquid, gel, or solid) between two electrodes or plates of an electrolytic capacitor at least one of which is covered by a dielectric lm. 2.3.4 added March 3, 2008 MARCH 3, 2008 CAPACITORS - UL 810 6UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL 2.3.5 ELECTROLYTIC CAPACITOR A capacitor consisting of two conducting electrodes whose anode has a metal oxide lm. Th