ARMY A-A-52074-1990 CLOTH SATIN LINING MATERIAL《里子材料有光缎纹细呢》.pdf

1、I A-A-5207Ll 83 7777774 0056334 b W 3 A-A-52074 July 2, 1990 COMMERCIAL ITEM DESCRIPTION CLOTH, SATIN, LINING MATERIAL The General Service Administration has authorized the use of this commercial item description in preference to Military Specification MIL-C-43525. 1. CLASSIFICATION 1.1 Classificati

2、on. This commercial item description covers satin, woven, lining material in the following types as specified (see 5.2). Type I - Rayon face and cotton or rayon back Type II - Acetate face and rayon back 2. SALIENT CHARACTERISTICS 2.1 General description, The cloth shall be a 5 or 8 harness satin we

3、ave such that the face warp yarns for the type I shall be multifilament rayon and the type II shall be multifilament acetate. The back filling yarns for the type I shall be either combed cotton spun into singles or multifilament rayon, and the type II shall use multifilament rayon yarns. The width s

4、hall be as specified (see 5.2) and shall be the minimum acceptable width inclusive of the selvage when fly-shuttle looms or shuttleless looms with tuck-in selvages are used; For all other shuttleless looms the width measurement shall be made between the last warp yarn on each side excluding the prot

5、ruding fringe(s), The cloth shall be finished so as to provide a lustrous finished face and a napped back, The color of the finished cloth (face side), shall be as specified (see 5.21, and shall match the standard sample when viewed under filtered tungsten lamps that approximate artificial daylight

6、and that have a correlated color temperature of 7500 + 200K, with illumination of 100 - + 20 foot candles, and shall be a good match to the standard sample under incandescent lamplight at 2300 - + 200K. Beneficial comments, recommendations, additions, deletions, clarifications, etc., and any other d

7、ata which may improve this document should be sent by letter to: Commander, U.S. Army Natick Research, Development, and Engineering Center, ATTN: STRNC-ES, Natick, MA 01760-5014. AMSC N/A FSC 8305 DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited. 4D- Provided by IHSNo

8、t for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-52074 83 9999974 0056335 m A-A-5 2074 2.2 Physical requirements. The finished cloth shall conform to the requirements listed in table I. TABLE I. Physical requirements Characteristic Type I Type II Test Method l/ Ya

9、rn identification Colorfastness to: Gas fading Perspiration Wet drycleaning Dry crocking (min) Wet crocking (min) (Black or dark blue colors) Weight, oz./sq.yd. (min) Yarns, per inch (min) : Warp Fi 11 ing Breaking strength, lbs. (min): Warp Fi 11 ing Thickness, in. (min) Shrinkage, percent (max): W

10、arp Fi 11 ing Rayon and Cotton Good Good Good 2.5 z/ - 1.5 - 4/ 8.2 3.5 4/ 190 48 140 80 0.020 4.0 2.0 Acetate and Rayon Good Good Good 2.5 q/ - 1.5 - 4/ 6.5 3.5 4/ 194 46 120 75 O. 015 4. O 2. o - 2/ 3/ 5 680 5622 565 1 565 1 565 1 5041 5050 5050 5100 5100 5030 5580 5580 - l/ The test methods indic

11、ated,from FED-STD-191 Textile Test Methods, have * been found acceptable to determine if the cloth meets the stated requirements. If the Government requires proof that the cloth meets the stated requirements, the test methods indicated shall be used. - 2/ A certificate of compliance shall be submitt

12、ed and will be acceptable for the stated requirements. - 3/ Refers to AATCC Method Number 164 “Colorfastness to Oxides of Nitrogen in the Atmosphere Under High Humidities“. 1 4/ Refers to AATCC Chromatic Transference Scale ratings. 2 Provided by IHSNot for ResaleNo reproduction or networking permitt

13、ed without license from IHS-,-,-b A-A-5207L1 83 7777774 0056336 T W A-A-5 207 4 2.3 Length and put-up. For Government procurements only, unless otherwise specified (see 5.2), the cloth shall be furnished in continuous lengths of not less than 50 yards. The cloth shall be put-up full width on rolls a

14、s specified in 4.1. 3. QUALITY ASSURANCE 3.1 Certification. The contractor shall certify, and maintain substantiating evidence, that the product offered meets the salient characteristics and requirements of this Commercial Item Description, and that the product conforms to the producers own drawings

15、, specifications, standards, and quality assurance practices. The Government reserves the right to require proof of such conformance prior to first delivery and thereafter as may be otherwise provided or under the provisions of the contract. 3.2 Visual examination. Lots of cloth shall be inspected i

16、n accordance with MIL-STD-105. The inspection level shall be II and the acceptable quality level (AQL), expressed in terms of defects per hundred units, shall be 6.5. The lot size shall be expressed in units of yards. The sample unit shall be one linear yard. The cloth shall be examined for the foll

17、owing defects: hole, cut, tear, missing end or pick, thick or thin areas, permanent crease, slubs, slugs or gout, shade bar, streaks, spots, stains or uneven dying. 3.3 Length examination. During the yard-by-yard examination, each roll in the sample shall be examined for length. Any length found to

18、be less than the minimum specified or more than 2 yards less than the length marked on the roll ticket shall be considered a length defect. If two or more rolls in the sample are defective with respect to length or if the total of the actual lengths of rolls in the sample is less than the total of l

19、engths marked on the roll tickets, the lot shall be rejected. 3.4 Regulatory requirements. The offeror/contractor is encouraged to use recovered material in accordance with Public Law 04-580 to maximum extent practicable. 4. PACKAGING 4.1 Packaging. The cloth shall be rolled on a convolute or spiral

20、-wound chipboard tube. The tube shall have a smooth finish surface that will prevent the fibers of the chipboard from transferring to the cloth. Each roll of cloth, put-up as specified, shall be wrapped with 60-pound minimum basis weight kraft paper in such a way that the roll shall be wrapped so th

21、at the paper shall encircle the roll at least once with a minimum overlap of 3 inches, and the width of the paper shall be sufficient to fold over and protect the ends of the roll. Gummed paper tape, with a minimum width of 2-1/2 inches shall be applied to the overlap seam the full length of the rol

22、l and across each end. 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-E A-A-5207Y 83 = 7777774 0056337 II A-A-52074 4.2 Packing. Each wrapped roll shall be enclosed in a close-fitting polyethylene film tube with a minimum thickness of 0.004 inches

23、 or each wrapped roll shall be enclosed in a bias-sewn tubing made from woven polypropylene cloth. The tube shall be secured by heat-sealing, by means of a mechanical tie, or by plastic ties with lock-end. Alternately, a maximum of 325 pounds of rolls of kraft-wrapped cloth shall be packed in a snug

24、-fitting double-walled fiberboard container known as a double cover, and shall consist of a body or joined liner and two covers. Corrugated fiberboard with a minimum bursting strength of 500 pounds shall be used, The container shall be strapped with metallic straps not less than 1/2 by 0.020 inch or

25、 non-metallic straps not less than 7/16 by 0.030 inch. 4.3 Marking. In addition to any special markings required by the contract or purchase order, rolls and shipping containers shall be marked in accordance with MIL-STD-129. Each roll shall have a piece ticket (identification tag) affixed with a 5-

26、ply minimum cotton string or a plastic tag hanger. The tag shall have u reinforced eyelet and shall be legibly printed, using water insoluble ink, with the following information: Procurement Agency National Stock Number Item Description Contractor Width Fiber Content Contract or Purchase Finish or G

27、reige Mil Roll Number Lot Number Piece Number Yardage Order Number 5. NOTES 5.1 Intended use. The type I cloth is intended for use as a lining in the mans and womanss overcoat. The type II cloth is intended for use only as sleeve lining on the removable lining for the mans and womans all-weather coa

28、t. 5.2 Acquisition requirements. Acquisition documents must specify the following: _ . a. Title, humber and date f this document b. Type of cloth required (see 1.1). c. Width of cloth required (see 2.1). d. Color of cloth required (see 2.1). e. Length and put-up if other than specified (see 2.3). 5.

29、3 Sources of documents. 5.3.1 Sources of nongovernment association documents. AATCC Chromatic Transference Scale Rating and AATCC Test Method Number 164,are available from: 4 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-52074 83-W 7777774 0056

30、338 3 & A-A-5 2 O 7 4 American Association of TextilqChemists and Colorists (AATCC) PO Box 12215 Research Triangle Park, NC 27709-2215 5.3.2 Source of government documents. Copies of Military and Federal documents are available from: Standardization Document Order Desk Building 4D 700 Robbins Avenue

31、 Philadelphia, PA 19111-5094 MILITARY INTERESTS: - Custodians Army - GL Navy - NU Air Force - 11 Review activities Army - MD CIVIL AGENCY COORDINATING ACTIVITY: GSA - FSS PREPARING ACTIVITY: Army - GL Project 8305-0345 Navy - CG Air Force - 82, 99 (I) DLA - CT 5 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-