ARMY A-A-52429 A-2009 VALVE SOLENOID OPERATED [Replaced ARMY MIL-V-62381 A CANC NOTICE 1 ARMY MIL-V-62381 A ARMY MIL-V-62381]《电磁控制阀[代替 ARMY MIL-V-62381 A CANC NOTICE 1 ARMY MIL-V-6.pdf

1、Comments, suggestions, or questions on this document should be addressed to U.S. Army Tank-automotive and Armaments Command, ATTN: RDTA-EN/STND/TRANS, MS# 268, 6501 E. 11 Mile Road, Warren, MI 48397-5000 or emailed to DAMI_STANDARDIZATIONconus.army.mil. Since contact information can change, you may

2、want to verify the currency of this address information using the ASSIST Online database at http:/assist.daps.dla.mil. AMSC N/A FSC 4810 INCH-POUND A-A-52429A(AT) September 8, 2009 SUPERSEDES A-A-52429(AT) 15 February 1993 COMMERCIAL ITEM DESCRIPTION VALVE, SOLENOID OPERATED The General Services Adm

3、inistration has authorized the use of this commercial item description (CID) as a replacement for MIL-V-62381A(AT) which is cancelled. 1. SCOPE. This CID establishes the requirements for a direct acting, poppet style, two-way shutoff solenoid operated valve for use on a military ground vehicle elect

4、ronic drive system as an emergency bypass valve. 2. SALIENT CHARACTERISTICS. 2.1 Materials. Materials shall be as specified herein. It shall be free from defects which adversely affect its performance or serviceability. The use of recovered material made in compliance with regulatory requirements is

5、 acceptable providing that all requirements of this CID are met (see 5.5). 2.1.1 Material compatibility. Materials for the solenoid valve shall be compatible with the hydraulic fluid, petroleum or synthetic base, used to inhibit corrosion, improve the low-temperature flow, viscosity characteristics

6、and resistance to oxidation of the valve. 2.1.2 Age-sensitive materials. Age control of the valve assembly should be based on the cure date of the oldest elastomeric component. The maximum age of the elastomeric item at time of acceptance by the Government shall not exceed 32 quarters for hoses and

7、40 quarters for O-rings (see 2.12.1). Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-52429A(AT) 2 2.1.3 Metals. Metals shall be corrosion resistant or suitably treated to prevent corrosion. The use of dissimilar metals, especially brass, copper,

8、 or steel in intimate metal to metal contact, shall be avoided. 2.2 Design and construction. The solenoid valve shall be a direct acting, poppet style shutoff valve, normally closed. The solenoid must be energized for the valve to remain open and allow flow of fluid. The solenoid valve shall conform

9、 to Drawing 12265543 and other applicable drawings, specifications and standards (see 5.2). 2.2.1 Operating fluid. The valve shall operate satisfactorily with hydraulic fluid (see 2.1.1). 2.3 Performance. 2.3.1 Proof pressure. With outlet port plugged, a pressure to the inlet port at a rate of 25,00

10、0 pounds per square inch (psi) per minute is applied until a pressure of 4,500 psi is obtained. The valve shall withstand this pressure for a period of 2 minutes without permanent deformation, rupture, or measurable external leakage. 2.3.2 Burst pressure. With outlet port plugged, a pressure to the

11、inlet port at a rate of 25,000 psi per minute is applied until a pressure of 7,500 psi is obtained. The valve shall withstand this burst pressure for a period of 2 minutes without rupture of internal or external parts. Solenoid valves subjected to this test shall be indelibly marked as damaged and s

12、hall not be delivered as acceptable units. 2.3.3 Pull-in voltage. With the inlet at a maximum operating pressure and with the discharge restricted to maintain rated flow, the valve shall actuate at any voltage applied to the solenoid within a range between 18 and 30 volts direct current (Vdc). 2.3.4

13、 Hold-in voltage. When energized with greater than 24 Vdc at maximum operating pressure and the discharge restricted to maintain flow, the valve shall not release at any voltage to the solenoid greater than 16 Vdc. 2.3.5 Coil current. With solenoid activated, the actuating current shall not exceed 0

14、.625 ampere (A) dc at 30 Vdc and at 77 degrees Fahrenheit (F). 2.3.6 Insulation resistance. With 500 Vdc applied between the coil terminals connected together and the case, there shall be at least 100 megohms of resistance. 2.3.7 Dielectric withstanding voltage. The solenoid valve shall be capable o

15、f initially withstanding 500 V root mean square (rms), 60 Hertz (Hz) for 1 minute between terminals tied together and the case. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-52429A 3 2.3.8 Voltage transient. The valve shall perform as specified

16、 when subjected to transient voltages as specified in MIL-STD-1275. 2.3.9 Rated flow. The flow capacity of the valve shall be not less than 0.25 gallon per minute (gpm), inlet to outlet, with a pressure drop across the valve of 75 psi. 2.3.10 Internal leakage. With the solenoid de-energized and the

17、valve closed, a pressure of 3000 psi shall be applied to the inlet port and held for 2 minutes; the internal leakage at the outlet shall not exceed 0.25 ml after 2 minutes. 2.3.11 External leakage. There shall be no evidence of leakage through external seals. Verification is done by visual examinati

18、ons. 2.3.12 Operating time. The units shall open in not more than 1 second by establishing flow at a rate of 0.25 gpm at 3000 psi after the solenoid shown in drawing 12265543 test circuit has been energized. 2.3.13 Closing time. The units shall close in not more than 1 second by terminating flow aft

19、er the solenoid shown in drawing 12265543 test circuit has been de-energized. 2.4 High temperature. The solenoid valve shall operate when subjected to a high ambient temperature of 140F. The valve unit shall not be damaged nor its performance impaired after storage in a non-operating mode at a high

20、ambient temperature of 158F. 2.5 Low temperature. The solenoid valve shall operate when subjected to a low ambient temperature of minus (-) 26F. The valve unit shall not be damaged nor its performance impaired after storage in a non-operating mode at a low ambient temperature of -65F. 2.6 Hydraulic

21、fluid temperature. The solenoid valve shall operate using hydraulic oil in accordance with 2.1.1 at operating oil temperatures of -26F to 170F with ambient air conditions as specified in 2.4 and 2.5. 2.7 Shock (non-operating). The units shall operate after exposure to a shock impulse of 25 gravity u

22、nits (g) for 11 milliseconds (ms), half-sine wave form. 2.8 Vibration (non-operating). The valve shall meet the performance requirements and show no evidence of failure or damage after performance of a vibration test in accordance with 2.8.1 and 2.8.2. 2.8.1 Low frequency. The valve shall be subject

23、ed to a simple harmonic motion having an amplitude of 0.03 inch (in.) (0.06 in. maximum total excursion) with the frequency being varied uniformly between the approximate limits of 10 to 55 Hertz (Hz). The entire frequency range, Provided by IHSNot for ResaleNo reproduction or networking permitted w

24、ithout license from IHS-,-,-A-A-52429A(AT) 4 10 to 55 Hz and back to 10 Hz, shall be traversed in approximately one minute. This motion shall be applied for 2 hours in each of three mutually perpendicular axes. 2.8.2 High frequency. The valve shall be subjected to a simple harmonic motion having an

25、amplitude varied to maintain a constant peak acceleration of 10gs (peak), the frequency being varied logarithmically between the approximate limits of 55 and 2000 Hz. The entire frequency range of 55 to 2000 Hz (no return sweep) shall be traversed in 35 +/- 5 minutes, except that in the vicinity of

26、what appears to be resonance and in order to facilitate the establishment of a resonant frequency, the above rate may be decreased. Valves shall be vibrated for 5 minutes at each of two resonant frequencies observed. This procedure shall be performed in each of three mutually perpendicular axes. Int

27、erruptions are permitted provided the requirements for rate of change and test duration are met. 2.9 Salt-fog (non-operating). A valve conditioned for 2 hours at 95F, exposed for 48 hours to salt-fog at fallout rate between 0.5 and 3 millimeters per 80 square centimeters (cm2) per hour, then stored

28、in a standard atmosphere for 48 hours for drying, shall operate without evidencing any malfunction or failure. 2.10 Fungus. The solenoid valve shall be constructed of only materials that are fungus non-nutrient, where possible. Fungus growth shall not degrade performance. 2.11 Cleanliness. The valve

29、 shall be precision cleaned (see 5.3). Upon completion of testing a sufficient quantity of fluid shall be retained in the valve to assure proper preservation during extended storage and shipment. Ports shall be covered with suitable plugs. 2.12 Identification and marking. Identification and marking

30、shall be permanent and legible and, unless otherwise specified in Drawing 12265543, shall include the manufacturers identification code (CAGE), the contract number, the engineering drawing part number, and the national stock number (NSN) (see 5.2). 2.12.1 Cure date. The cure date shall be physically

31、 and legibly marked on the exterior of the valve assembly. 2.13 Workmanship. Workmanship shall be in accordance with the manufacture of a high quality solenoid valves. This shall be evidenced by the absence of defects detrimental to its life, serviceability, or appearance. 3. QUALITY ASSURANCE PROVI

32、SIONS. 3.1 Responsibility for inspection. The contractor is responsible for the performance of all inspections (examinations and tests). Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-52429A 5 3.2 Contractor certification. The contractor shall c

33、ertify and maintain substantiating evidence that the product offered meets the salient characteristics of this CID and that the product conforms to the producers own drawings, specifications, standards, and quality assurance practices. Items with known defects shall not be submitted for Government a

34、cceptance. The Government reserves the right to require proof of such conformance prior to the first delivery and thereafter as may be otherwise provided for under the provisions of the contract. 4. PRESERVATION, PACKAGING, PACKING, LABELING, AND MARKING. Preservation, packaging, packing, labeling,

35、and marking for the desired level shall be as specified in the contract (see 5.2). 5. NOTES. (This section contains information of a general or explanatory nature that may be helpful, but is not mandatory.) 5.1 Addresses for obtaining copies of referenced documents. 5.1.1 Government specifications a

36、nd standards. MIL-STD-1275 “Characteristics of 28 Volt DC Electrical Systems in Military Vehicles” is available from the Document Automation and Production Service, Building 4/D, 700 Robbins Avenue, Philadelphia, PA 19111-5094 or website: http:/assist.daps.dla.mil/quicksearch/. 5.1.2 Other Governmen

37、t documents, drawings, and publications. Drawing 12265543 “Valve, Solenoid Operated” is available from the Contracting Officer, U.S. Army Tank-automotive and Armaments Command, 6501 E. 11 Mile Rd, Warren, MI 48397-5000. 5.2 Ordering data. Acquisition documents must specify the following: a. Title, n

38、umber, and date of this CID. b. If required, the specific issue of individual documents referenced (see 5.1.1 and 5.1.2). c. Title, number and revision letter of the applicable engineering drawing and part number (see 2.2 and 2.12). d. Selection of applicable level and packaging requirements (see 4.

39、). 5.3 Precision cleaning. This method is used to achieve a level of product cleanliness greater than the level normally detected by visual means. Articles should be visibly clean prior to precision cleaning. Precision cleaning is performed in a controlled environment, and is intended to remove part

40、icles, films, biological forms, fibers and other forms of contaminants that are usually not visible, but which could degrade the product or process. The level of precision Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-52429A(AT) 6 cleanliness s

41、hould be verified and evidence of inspection and acceptance provided. Precision cleaned articles should be packaged immediately after verification of cleanliness, or suitably protected prior to leaving the controlled environment. 5.3.1 Precision cleaning solutions/fluids. Precision cleaning solution

42、s or material should not react with, combine with, etch, or otherwise cause immediate or latent degradation of the item being cleaned. Precision cleaning fluids should be filtered, and controlled. Their cleanliness level should be verified as being sufficient to achieve the specified product cleanli

43、ness. 5.4 Cross-reference data. Solenoid valves conforming to this CID are interchangeable/ substitutable with solenoid valves conforming to MIL-V-62381A(AT), dated 18 December 1985. 5.5 Regulatory requirements. The offeror/contractor is encouraged to use recovered materials to the maximum extent pr

44、acticable, in accordance with paragraph 23.403 of the Federal Acquisition Regulation (FAR) (see 2.1). 5.6 Metric product. The solenoid operated valves made to metric dimensions will be considered on the following basis: a. Products manufactured to metric dimensions will be considered on an equal bas

45、is with those manufactured using inch-pound units, provided they fall within specified tolerances using conversion tables contained in the latest revision of IEEE/ASTM SI 10, and all other requirements of this CID are met. b. If a product is manufactured to metric dimensions and those dimensions exc

46、eed the tolerances specified in the inch/pound units, a request should be made to the contracting officer to determine if the product is acceptable. c. The contracting officer has the option of accepting or rejecting the product. Custodian: Preparing Activity: Army - AT Army - AT (Project 4810-2009-

47、002) NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at http:/assist.daps.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-